Dodge Dakota Fuel Pump Replacement (2001-2004)

  Рет қаралды 110,566

Tony The Truck Guy

Tony The Truck Guy

Күн бұрын

Пікірлер: 272
@fastman6148
@fastman6148 9 ай бұрын
I have been working on vehicles for well over 50 years. I always thought that the older vehicles were way easier to work on but that is probably only my imagination. Anyway, I have an '02 Dakota quadcab which is a daily driver in our family. The fuel pump quit on it. I got new parts to repair it and I got to looking at how to do this. While there really is no mystery, it is a huge help to see someone who knows the little tricks for hoses, electrical connectors, fuel filler spout and tank straps actually show us how in a video. I know it is going to save me breaking something when I do this job on our truck! Thanx so much for making the video, explaining as you went and posting it!
@TonyTheTruckGuy
@TonyTheTruckGuy 9 ай бұрын
I appreciate it! Some people prefer to pull the bed, but I found this way to be better for me. Good luck!
@fastman6148
@fastman6148 8 ай бұрын
@@TonyTheTruckGuy On a quad cab though, the fuel pump is under the cab, so, removing the bed will not get access to the fuel pump and you'll still be underneath the truck removing the tank anyway, By the way, due to my working out of town a lot recently, I only got this fuel pump changed this past weekend, which, in Canada, where I live, was a long weekend (Queen Victoria's birthday). I never did find the correct hardware for the fuel tank straps due to most places being closed.... I used two pieces of 3/8" NC by 3 1/4" long "all thread" which I double nutted up in the crossmembers and aligned the hexes while tightening them. I was easily able to hold them from turning with an open end wrench. Anyway, it is all back together and running. It starts. now, on about the first crank of the engine. Like I said a few weeks ago - thanx again for posting this video. I looked at a few others as well - yours was, I must say, the most to the point, coherent and easy to follow.
@TonyTheTruckGuy
@TonyTheTruckGuy 8 ай бұрын
@@fastman6148 Haha yeah I had forgotten that the different cab configurations change where the pump is accessed. Thanks for the update and the positive feedback! Glad you got time to get it done!
@someguyintexas1053
@someguyintexas1053 2 жыл бұрын
This is a perfect example of what every "How To" video should be. SINCERE THANKS. 🙂
@cmanofthewoodscentralus3217
@cmanofthewoodscentralus3217 2 ай бұрын
Enjoyed your video with a lot of good information. I did notice when you were installing the bolts for the filler neck debris bouncing inside the filler tube. Might be a good idea to have slipped a bag over the filler neck while positioning tank in place to prevent debris from falling in. Thank You for your detailed video.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 ай бұрын
@@cmanofthewoodscentralus3217 Yeah that bag idea would have been good. Thankfully there’s at least the filter sock on the bottom of the pump to catch the debris. Sadly this truck was crushed a few years back but I’m glad the information is still helpful!
@theturianguy4542
@theturianguy4542 3 жыл бұрын
Really appreciate the video, i always second guess myself on what to do with these kinds of things. I'm glad i live in such a dry climate so i don't have to deal with all that rust. this seems much easier than lifting the bed off lol.
@jimfisher8990
@jimfisher8990 Жыл бұрын
So I just got done replacing my fuel pump after watching your video and it was very helpful but I wanted to add a couple points that I came across when I did mine. first of all I have a 99 Dakota sport 5.2 L. when I tried to drop the tank, I couldn’t do that without disconnecting the fuel inlet and vacuum line because it hit the frame. The bolts for removing the straps holding the tank up were longer than I could find any socket to fit so it was all box and wrench on loosening, which took forever. That ring that holds the pump in was got awful tight and I thought I was going to break something with all the pounding. I did to get that loose. Once I got the ring off and started to remove the pump, I found that it was full of at least a quart of gas which I tried to pour back in the tank, gassing everywhere. But all in all it was something I wouldn’t want to do again, but I succeeded.
@fastman6148
@fastman6148 9 ай бұрын
Thanx for posting your comment. My guess is that the fuel pump on the earlier (97-00) trucks may be different than the truck that was shown in this video. I also watched a video showing this job done on a late '90s truck and the fuel pump has a large tub surrounding the fuel pump, so I guess that is what you must have been dealing with... Anyway, thanx again for you sharing your experience.
@66thru68veteran
@66thru68veteran 3 жыл бұрын
Incredibly concise video ! Great camera work , and no UHHHS or UHHMMMS .
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
Haha thanks. I try to cut as many of those out as I can 🤣
@solarflare4259
@solarflare4259 Жыл бұрын
Excellent, detailed, video.. My truck has about 210K and even if the fuel pump still works great ,I plan to install a new one... Thank you for posting!
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
Thank you, glad I could help!
@xxxdpgxxxx1389
@xxxdpgxxxx1389 Жыл бұрын
Mine just hit 150k runs like new
@DavidSmith-db1mk
@DavidSmith-db1mk Жыл бұрын
great video ! um do you mind trying one more time on my Dakota ?
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
🤣
@benfell2984
@benfell2984 29 күн бұрын
Right!?!? 😂
@cordarin7
@cordarin7 2 жыл бұрын
fuel tank strap bolts are 15mm fyi
@bubbasmith382
@bubbasmith382 4 жыл бұрын
Thank you for showing in detail how to undo all the stupid clips!! that is a huge help for me!
@JohnMW43
@JohnMW43 4 жыл бұрын
This video is saving my life right now. Thanks a million!
@michaelthelastwarrior
@michaelthelastwarrior 3 жыл бұрын
Thanks for the video; very helpful for my fuel pump replacement. That joke of a filter on bottom of pump, was laying at bottom of tank.
@johnstone8760
@johnstone8760 3 жыл бұрын
But, I would say that this video is very educational if someone didn't know the process of this. Great 👍
@Rockfishreseller2022
@Rockfishreseller2022 Жыл бұрын
Thanks, man! This is EXACTLY what i needed!
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
Glad I could help!
@gavinhoush8127
@gavinhoush8127 4 жыл бұрын
Hi Tony, thank you for the great video! I have a 98 Dakota with the 3.9L V6 engine. I was looking at KZbin videos to see how hard it is to replace the fuel filter. My truck stumbles at idle when it's in gear, say at a stop light for instance. After watching your video and seeing that the filter on the bottom of the pump looks literally like a piece of fabric somehow attached to the bottom of the pump, I'm almost ready to just sell the thing. What a joke! I'm kicking myself still after 22 years for not buying another make!
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
22 years is a pretty long service life for a vehicle though, I'd say you got your money's worth. But yeah, the filters are just cheap. Your pump or regulator may be bad, but if the 98 is like my 02, then the pump, regulator, and filter are all 1 assembly.
@volinski
@volinski 4 жыл бұрын
I have a 98 as well and though I don't have to do the pump I am doing the filler neck and hoses, and im sooo happy to see that it has hoseclamps on the tank side, cuz I was told it was quick connects
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
@@volinski Yeah, those are a pain haha
@c2protect
@c2protect 3 жыл бұрын
22 years and you're complaining about a little filter...?
@jeffnajmowicz5634
@jeffnajmowicz5634 2 жыл бұрын
Awesome job, one of the better how to videos I've seen in a while. Thanks!!!
@zzz7zzz9
@zzz7zzz9 3 жыл бұрын
coulda just waited an extra day or two, and those straps mighta rusted clean through and dropped the tank themselves. this was a great vid on this job.
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
Yeah, they were getting a little anemic haha
@zzz7zzz9
@zzz7zzz9 3 жыл бұрын
@@TonyTheTruckGuy i thought mind was getting rusty, but it's looking pretty darn good now.
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
@@zzz7zzz9 😂
@swav5280
@swav5280 2 жыл бұрын
Your video was excellent, helped me out quite a bit. Note the electric coupler has two plastic nubs that hold it to the top of the frame making it very difficult to disconnect. I broke those off out of frustration and found that they are on the new part, so no problem. Also, despite a new fuel pump, still crank no start, so back to the drawing board with other options...
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Can you hear the pump run when you key the ignition on?
@swav5280
@swav5280 2 жыл бұрын
@@TonyTheTruckGuy loud and clear, yes
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
@@swav5280 Any codes?
@swav5280
@swav5280 2 жыл бұрын
@@TonyTheTruckGuy no I don’t have a reader, will be doing that this week and let you know how it goes
@gregoryiightkep3102
@gregoryiightkep3102 2 ай бұрын
Awesome video, very informative and easy to follow
@TonyTheTruckGuy
@TonyTheTruckGuy 2 ай бұрын
@@gregoryiightkep3102 Thank you! Glad I could help.
@alpersichino1486
@alpersichino1486 10 ай бұрын
😮😮😮 usually when my fuel pumps go out I have a full tank of gas!!!😮😮😮😮😮😮😮😮
@TonyTheTruckGuy
@TonyTheTruckGuy 10 ай бұрын
Pretty typical 😂
@claudiotobar184
@claudiotobar184 4 жыл бұрын
Wow You have a huge rust problem there! Thanks for the throughly video anyway. Very useful with every detail
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Yeah....it should be a felony to use salt on the roads in the winter. Destroys everyone’s vehicles very quickly. Every time I see a plow truck, all I can think about is Johnny Depp in Pirates when he yells “stop blowing holes in my ship”! 😂
@claudiotobar184
@claudiotobar184 4 жыл бұрын
@@TonyTheTruckGuy hahaha
@lisasmith2016
@lisasmith2016 11 ай бұрын
Mine is a 2002 RT with the 5.9 liter and 16 gallon tank. SoCal truck, 139k., I understand tilting the bed and accessing from the top is the way to go, and you should replace the vac lines and wires running through while you are at it. Basically do all that stuff proactively so you don't have to do it again for another 20 years. Any suggestions on what specific parts should be replaced while i have the bed lifted? Getting ready to do my parts search now.
@TonyTheTruckGuy
@TonyTheTruckGuy 11 ай бұрын
Sadly, this truck has succumb to Midwest salty winter and went to the scrapyard a few years back, so no more 20 years for me lol. Awesome that yours is in that good of shape still. I’d say anything going to the fuel tank should be replaced. Straps, pump, filter, breather, the plastic EVAP lines and hoses. Only other thing that’s really under there besides the frame should be wiring harness and parking brake cable.
@glenwhitestofer6420
@glenwhitestofer6420 10 ай бұрын
Can't be done on the quad cab
@cadeltarat
@cadeltarat 2 жыл бұрын
Good video and informative. Man I really do fell for everyone that lives in back East or anywhere that they use salt on the roads.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Hell, I’m in the Midwest and they sure love salt here too lol
@cadeltarat
@cadeltarat 2 жыл бұрын
CALIFORNIA AND NEVADA NO CAR CANCER HERE
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
@@cadeltarat It’s just so damn hot 🥵
@raulterrazasreza1635
@raulterrazasreza1635 2 жыл бұрын
Very pleased for this video. well explanined. just what i needed. Thanks a lot.
@redtailhawk289
@redtailhawk289 7 ай бұрын
Great video why didn't dodge put a Schrader value on the gas line so that we could check the pump pressure ?
@TonyTheTruckGuy
@TonyTheTruckGuy 7 ай бұрын
@@redtailhawk289 I asked myself the same question lol
@ericandrew4063
@ericandrew4063 2 жыл бұрын
Nice video! Thanks for the clear detailed instructions.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Glad I could help!
@barryloftin4159
@barryloftin4159 2 жыл бұрын
That’s a great video dude very professional thanks
@jimfisher8990
@jimfisher8990 Жыл бұрын
First of all, I want to say for as clean as the outside of that truck is the underside is got awful bad rust wow
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
Yeah, she went to the scrapper a few years back. Good old road salt to thank for that.
@jacotacomorocco
@jacotacomorocco 11 ай бұрын
Looks like a Midwest truck frame lol I get it tho, they use a ton of road salt in wisco
@Swampyankeehomestead
@Swampyankeehomestead 2 жыл бұрын
Now would be a good time to get to that brake line. Seriously good video all I wanted to see was if I needed a special tool to remove the fuel line. Those connections can be a bear, spray with break clean and shop air is my only pointer.
@joeshumo9457
@joeshumo9457 Жыл бұрын
I don’t reuse those Fuel line clips. I have a ground switch on the dash to the fuel pump relay on a programmable timer switch in case of a loss of prime due to a leak, bad regulator or to put a yellow service line hose on the fuel rail schrader valve to pump some gas out. Using 6 ton jack stands under the rear axle with the driveshaft disconnected after removing the riveted in frame rail on the quad cab / extra cab and replacing them with bolts , helps a bunch. The factory straps I’ve modified by welding two sets for straps together to make it so the straps bolt in on both sides instead of the silly puzzle fitting ends that the factory uses on the drivers side. Lastly, the pump assembly can be made to be serviced separately if you take a little time and patience to modify it. The pump and regulator are available separately. You can plumb in a stand alone regulator on the fuel system as well and just ignore the regulator that failed and leave it. Remember to check for leaks, including injectors when the symptoms of a bad regulator appear as they can be very similar. I had the tiniest leak in my fuel line that you could imagine that haunted me for three tank removal processes in a row once. Treat rust early and often. Rust never sleeps.
@beancrane9595
@beancrane9595 2 жыл бұрын
hey what o2 sensor codes did you have that gives you an idea your fuel pump is bad?
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
None lol. I’ve never seen any O2 sensor codes trigger from a bad fuel pump. The regulator is build into the pump and the regulator went bad because it was cranking for a long time before it would start, that’s why I changed mine.
@beancrane9595
@beancrane9595 2 жыл бұрын
@@TonyTheTruckGuy there is only one filter located in the pump though right? I think I just need new filter but if it's In the pump might as well just change it
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
@@beancrane9595 Yeah it’s literally just the little sock style filter the clips to the bottom of the pump
@RJ6AV6
@RJ6AV6 3 жыл бұрын
perfect video man! thanks a bunch, gonna tackle this on my 02 4.7L QC 😩😅
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
It’s not too bad if the tank is low on fuel. I’d check your straps I’m advance and order them to change out if they’re rusty like mine. And make sure the pump seal doesn’t push into the tank when you install the pump. I didn’t catch mine pushed in slightly in 1 spot, you can actually see it happen around 11:29. So if I filled my tank over 3/4, it leaked lol.
@RJ6AV6
@RJ6AV6 3 жыл бұрын
@@TonyTheTruckGuy cool man I appreciate the reply! I'm in San Diego so there's no rust and like you I'm going to switch it out and probably sell it. Been a great truck never any major issues had it since 04 and she's at 192K. Thanks again and I'll definitely subscribe 👍👍
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
@@RJ6AV6 Thanks, and good luck!
@shaneneuy5019
@shaneneuy5019 2 жыл бұрын
Could I get mine out by taking bed off??crew cab 02 as well..tank full!!!
@sstevenson9293
@sstevenson9293 4 ай бұрын
Thank you so much for this video! We have the same vehicle, but unlike in your video our truck has a metal cross member from the left to right side of the frame below the gas tank. Did you have to take one out or bust the rivets? Because we can’t drop the front end like you did. This will be my 16 year olds daily driver to and from school, and we’re trying to make it as cost effective as possible to fix it up. And after dropping cash on replacing the whole front suspension, and back brakes, we’re going to hopefully get this done ourselves. Any advice would be so appreciated!
@TonyTheTruckGuy
@TonyTheTruckGuy 4 ай бұрын
@@sstevenson9293 No crossmember was on mine. You’ll probably have to grind and knock the rivets out and use bolts to reinstall it.
@sstevenson9293
@sstevenson9293 4 ай бұрын
@@TonyTheTruckGuythanks a ton. I know it was some time ago, but about how long do you think it took you from start to finish. I do have some experience changing fuel pumps, just not on a truck that is such a pain in the butt. Trying to decide if it’s worth the $900 to have done, or if it’s something I can complete in a few hours and save $600 bucks.
@TonyTheTruckGuy
@TonyTheTruckGuy 4 ай бұрын
@@sstevenson9293 Honestly I can’t remember with it being so long ago plus I was filming which adds time and then of course coming up for a fix on the strap bolts. If you didn’t have to mess with sucking the tank out and everything goes smoothly I’d say a couple hours.
@05council87
@05council87 9 ай бұрын
will it still prime if i didn't connect the fuel line to it? i'm trying to make sure it throws gas throw the port that leads to the engine
@TonyTheTruckGuy
@TonyTheTruckGuy 9 ай бұрын
If you key the ignition on with the pump plugged in and the fuel line disconnected, it will shoot fuel out of the line up at the tail where you have it disconnected. I would just leave the line connected and cycle the key a few times to prime it.
@AZOffRoadster
@AZOffRoadster 2 жыл бұрын
Glad I live in AZ. No rust at all on my 2002. Same with my '70 Challenger.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
I’d love to live in a state with less humidity and no road salt, but I’m not built for that desert heat haha.
@AZOffRoadster
@AZOffRoadster 2 жыл бұрын
@@TonyTheTruckGuy I suspect that in the near future, it might be too hot and dry to sustain ANY human life here. Relocation is crossing my mind. Somewhere with water would be nice.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
@@AZOffRoadster Is it really too much to ask for 60-80° year round with low humidity? 😂
@joeshumo9457
@joeshumo9457 Жыл бұрын
Kihei, Maui Hawaii.
@robertiiams2702
@robertiiams2702 2 жыл бұрын
Thank you for the video is there a reason why the fuel pump won't turn on after you hook it up is there any other relays that actually keep the power away from the fuel pump cuz mine doesn't turn on
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
First make sure you have the fuel pump connector fully engaged, then make sure the truck battery is good. There is likely a fuel pump relay in the fuse box under the hood, or the one above the drivers foot area, but I’m not sure which specific location it is.
@ericp3573
@ericp3573 Жыл бұрын
what engineer thought it would be good to have high pressure going through a metal line and have the end made of plastic?
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
It’s not really “high” pressure, but yeah engineers just love to F with people lol
@JamesSilcox-n5e
@JamesSilcox-n5e 6 ай бұрын
Thanks for the video!
@TonyTheTruckGuy
@TonyTheTruckGuy 6 ай бұрын
@@JamesSilcox-n5e Very welcome, good luck!
@HopCity22
@HopCity22 3 жыл бұрын
Great video! Thank you sir, I’m sure you made it look easier then it will be for me. haha but thank you.
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
Just make sure the seal between the pump and tank doesn’t fall in haha, I got mine all together and it leaks gas if you fill over 3/4 tank because the seal got messed up.
@HopCity22
@HopCity22 3 жыл бұрын
@@TonyTheTruckGuy haha noted! Thanks 👍
@ebay2291
@ebay2291 4 жыл бұрын
Thank you for posting this video helped me a lot
@devonabraham3588
@devonabraham3588 3 жыл бұрын
a tip: watch movies on Flixzone. Been using it for watching loads of movies recently.
@lennoxtravis9487
@lennoxtravis9487 3 жыл бұрын
@Devon Abraham yup, been using Flixzone for since december myself :)
@mcsew2k
@mcsew2k 7 ай бұрын
Safety first! Disconnect the negative clamp on the battery!
@TonyTheTruckGuy
@TonyTheTruckGuy 7 ай бұрын
Yeah I suppose if you plan on intentionally creating a short circuit over an open tank lol
@JECHOE
@JECHOE 6 ай бұрын
What other vehicles have the same fuel pump ? !!!!
@TonyTheTruckGuy
@TonyTheTruckGuy 6 ай бұрын
@@JECHOE Not sure. Could Google the part number or on Amazon and see what other vehicles it’s listed for.
@carsonfarlow9998
@carsonfarlow9998 3 жыл бұрын
I have a quick question. I think I bought the same pump and I compared it the original and the original is a couple inched longer. Does this mean I won’t be able to get gas from the bottom of the tank? How did yours work out over a longer period of time?
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
I sold this truck not long after replacing the pump, so I’m not positive how well it has held up. The precision brand pump that I got had 3 little feet o. The bottom of it that sat against the floor of the tank. I guess I never actually measured it and compared it to the original pump. But if it’s off by a few inches as you say, then yea I’d be a little concerned on if the new pump will be able to pick up fuel that’s low in the tank.
@james-taylornewton703
@james-taylornewton703 2 жыл бұрын
What type of pump should I buy. I don't want to get new one and have same problem you had
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
OEM is probably your best bet
@JECHOE
@JECHOE 6 ай бұрын
Also need too know what fuel pump it is
@TonyTheTruckGuy
@TonyTheTruckGuy 6 ай бұрын
@@JECHOE Links in video description.
@JC-kk6hr
@JC-kk6hr 4 жыл бұрын
This is what I needed..my 2002 is trying to start, and we put some gas into to the carb..it tried to kick it but soon died. Im thinking this is the solution. nicely done on the vid..
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Thanks and good luck!
@danielelkins247
@danielelkins247 4 жыл бұрын
2002 with a carburetor? wut
@PajamaSenpai
@PajamaSenpai 4 жыл бұрын
My fuel pump is fine but I may need to drop the tank due to EVAP codes. This video is super helpful. Is this a rust belt truck? The rust on you truck is insane.
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Haha, unfortunately, yes. Minnesota.
@Idontanswerquestionz
@Idontanswerquestionz 4 жыл бұрын
Before dropping the tank check the power to your evap solenoid. If it doesn't modulate and is just steady power it might be a bad ecu. Replaced the whole evap system only to finally check the electrical side. Should have known after all the work to fix the damn no bus issue on that ecu. Stupid ass jtec garbage.
@killamilla9027
@killamilla9027 Жыл бұрын
is this a 24 gallon tank?
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
I believe it was a 23 or 24 yeah
@strange9673
@strange9673 3 жыл бұрын
Great video thanks for the help my friend🤟🏽
@TheTesemahb
@TheTesemahb 3 жыл бұрын
Vary informative and helpful, thanks
@THEBIBLEWAY238
@THEBIBLEWAY238 2 жыл бұрын
Where is the fuel filter located???
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
It may vary by year, but this one didn’t have a legit fuel filter, just the small “sock” or “screen” style filter that clips onto the bottom of the pump in the tank.
@burittohoper
@burittohoper 2 жыл бұрын
Question. Can you tilt the bed like on Chevy Silverado‘s?
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Tilt? I’d remove the bed completely or slide it back if anything but that seems like more work to me.
@joshwalters3148
@joshwalters3148 Жыл бұрын
@@TonyTheTruckGuy from what I can see the pump is blocked by half the cab in a quad cab. Any tips on getting straps back in place? I'm about ready to Jerry rig some brackets lol
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
@@joshwalters3148 Another reason I just pulled the tank haha. It’s been so long since I did this job, but I think I had the stink fairly empty and had another buddy help start the straps as I lifted the tank or used a jack to hold it up.
@joshwalters3148
@joshwalters3148 Жыл бұрын
@@TonyTheTruckGuy ended up ordering new straps.....tried shaping the old ones, and one broke, they come in pairs so both it is lol.....truck runs great, transmission needs a rebuild though, prolly gonna sell it cheap lol
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
@@joshwalters3148 There ya go haha
@kathleenantonich3431
@kathleenantonich3431 2 жыл бұрын
Hi Tony. I have a 2004 Dodge Dakota 6 Cylinder truck with an error code of P0310, a misfire in the 10th cylinder. I know a list of quick cheap fixes to hopefully conquer my problem. Yay for me (said sarcastically with a giggle). I'm confused why this error code is about a tenth cylinder when I only have six. Please explain???
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Yeah something is goofy there lol, I’ve never run into that. Almost sounds like the ECM has some internal issues going on. They’re pretty cheap to find used online though if you do end up needing one.
@chantron6946
@chantron6946 4 жыл бұрын
So fun fact for people that have a 98 and dont have torx bits, you dont have to disconnect the fuel hose, it can separate from the tank its self but if you have a full tank I wouldnt do it my way, mine is at about 3/4 so it wont be that bad
@agustinecamargo6723
@agustinecamargo6723 4 жыл бұрын
today my truck didnt move the fuel gauge do you think is a bad fuel pump and i need to replace it?
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
If the truck runs then the pump is good but the sending unit might be bad which is part of the pump so you’d have to replace the whole pump. That’s assuming the wiring to the pump is good
@agustinecamargo6723
@agustinecamargo6723 4 жыл бұрын
@@TonyTheTruckGuy great thanks for you help and this video is goin to help me replace the pump
@Fkidd702
@Fkidd702 4 жыл бұрын
Same. It just cranks. Shows the no gas sign and says " no bus" and check engine light is on too
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
You probably have different issues. Yours sounds like possible engine ECM failure or wiring/power/ground issue to the ECM. The "bus" is the communication line that your electronics use to communicate. I'm guessing the truck just cranks because the ECM isn't providing spark to the plugs or signal to the injectors.
@b38n8
@b38n8 2 жыл бұрын
How do I know which fuel pump I need to get?
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
I usually go on the O’reilly website and look up by year/make/model
@KevinTorres-xc2sv
@KevinTorres-xc2sv Жыл бұрын
Fuel gauge moving up and down , replacing it fixes that issue?
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
I guess maybe if it’s excessive bouncing but a little may be normal
@davidking4779
@davidking4779 19 күн бұрын
I had two bad pumps. Why do I have a rivited in cross member under my tank?
@TonyTheTruckGuy
@TonyTheTruckGuy 19 күн бұрын
@@davidking4779 Spare tire holder maybe?
@erty7012
@erty7012 3 жыл бұрын
If you have a short bed, the other option is slide the bed back about a foot. Easy access from there. Leave the tank where it is.
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
I probably my would have done that if I thought the bed bolts would come out without snapping haha
@erty7012
@erty7012 3 жыл бұрын
@@TonyTheTruckGuy Dodge trucks do have a notorious rust issue. No doubt about it.
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
@@erty7012 I’m sure 20 years in Minnesota winters hasn’t helped haha
@w00derice
@w00derice 3 жыл бұрын
I'll keep that in mind for mine whenever the time comes. 04 single cab 5 speed with truetrac, woot!
@sixfoursoul2538
@sixfoursoul2538 Жыл бұрын
nice truck!! , are those 31 tires?
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
Yeah they were 31x10.5 on 15x8 black rock wheels
@dariusdise
@dariusdise 4 жыл бұрын
With the tank down, is it possible to get to the topside of tire winch to replace it? I have a 2000 dodge dakota with 91K miles and for a while I've heard the whining noise from the pump. And the cable wire in the the tire winch snapped some time back. To kill two birds with one stone I wanted to tilt the bed and remedy both. But if there's enough room and leverage to gain access to the topside of the winch with the tank down then it may be best to remove the fuel tank rather than lift the bed, maybe? I currently have my spare in the back of the cab
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Honestly I don’t think the spare tire winch was directly above the fuel tank, but I can’t remember for sure and unfortunately, I no longer own the truck. I think the spare tire is further back than the tank, you’ll have to check. If it is, you may have to remove the bed or the crossmember that the spare tire winch is in.
@TheVjoenito5
@TheVjoenito5 4 жыл бұрын
Is it possible to fix the plastic where the filler neck connects to on the tank? its right above the pump. I have a bunch of cracks on mine where i believe fumes are coming from. I used JB Weld once but it seems to still be coming out. Been thinking of replacing the whole tank xD
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
You mean the white plastic part @ 7:56 where the fill neck hose connects to the tank?
@WillyBouy
@WillyBouy 3 жыл бұрын
Dont know for sure the exact location of the tank, re main truck body on this video but I have a Dakota extended cab. Just 4 bolts holding the pickup bed on so loosen the rear bolts where it bolts to the frame and take the two front bolts off, and presto, lift the bed up, prop it with a 2x4 and work from the top. The bed is much lighter than I thought and was very light. No disconnecting lights or tank etc: The pump is on the top of the tank. Whole process was about an hour. :-)
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
Mine was pretty rusty so I didn’t want to risk snapping off the bed bolts haha. And we didn’t have the man power or a lift to pick up the bed unfortunately.
@glenwhitestofer6420
@glenwhitestofer6420 10 ай бұрын
cab gets in the way on a quad cab,extended cab is fine
@JamesDvorak
@JamesDvorak 2 жыл бұрын
Great job!
@irideshortbus2845
@irideshortbus2845 4 жыл бұрын
How did you bring the 2 belts up to hold the tank in place again? It is extremely difficult to align the holes and get the stud back in
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Might require a second body to help lift up on the tank. I just went Hulk mode on it since the tank was pretty empty and pushed up real hard on the tank then grab the tank straps and shove them up into the hole. You might have to “massage” the straps by working out any slack in them from the frame side and then run your hands toward the end with the studs. You can tell if the tank and straps are positioned correctly if the curvature of the strap lines up with the tank. Otherwise you could try supporting the tank with a jack and then with 2 free hands, you should be able to get the straps started.
@irideshortbus2845
@irideshortbus2845 4 жыл бұрын
@@TonyTheTruckGuy thanks! Got it done. It took some serious strength to push that belt all the way up
@colingraham1464
@colingraham1464 4 жыл бұрын
Could you put on the video the gas tank straps info and what size your gas tank is. I have 03 and it has a 24 gallon tank trying to find the rite straps for it thanks and great video
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
I believe mine was also 24 gallon. I would just try RockAuto.com and select your year, make, model, and trim. I think I saw some on there at one point.
@colingraham1464
@colingraham1464 4 жыл бұрын
@@TonyTheTruckGuy thanks Tony thats where I was looking and what do you mean by trim ?
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
@@colingraham1464 Sport, SLT, etc. Sometimes they ask what trim and cab configuration you have
@colingraham1464
@colingraham1464 4 жыл бұрын
@@TonyTheTruckGuy thanks again Tony
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
@@colingraham1464 No problem!
@konasan
@konasan 2 ай бұрын
The original strap bolt(s) may have "U nuts". They rust out and the bolt just spins. I was able to reach up sith a cabide bladed sawzall and cut the bolt above the strap.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 ай бұрын
@@konasan Exactly haha
@konasan
@konasan 2 ай бұрын
@@TonyTheTruckGuy The Auto Parts store were useless for getting new U Nuts. But Ace Hardware had them. The nuts said they are M10 but galvanized 3/8" bolt fit so I used those for the reinstall in the hopes that the galvanizing might make the U Nuts last longer.
@stevenwalters8557
@stevenwalters8557 3 ай бұрын
Mine might be an 03 but i think its an 02 mine has a bracket goin from one frame rail to the other towards the front of the tank its nothin like this one. I had to take the drive shaft out to lower the tank but the tank wont come all the way down or out. I dont know why mine has the bracket but it isnt an easy job for sure hopefully mine will be running again tomorrow
@TonyTheTruckGuy
@TonyTheTruckGuy 3 ай бұрын
@@stevenwalters8557 sorry to hear that I’m curious why yours would be different being the same body style and all. Very interesting…
@shaneneuy5019
@shaneneuy5019 2 жыл бұрын
Can I get the fuel pump out if I take the bed off of a 2002 extended cab Dakota?? Looks like it won't without dropping tank at all??
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
You probably could, so long as you have a means to remove the bed.
@glenwhitestofer6420
@glenwhitestofer6420 10 ай бұрын
yes
@glenwhitestofer6420
@glenwhitestofer6420 10 ай бұрын
Glad I live in Victoria BC, no rust on mine
@darlingonzalez7693
@darlingonzalez7693 Жыл бұрын
I have a Dakota sport 2002 . The front driveshaft wasn't installed and I don't know how to do it right. I tried but I started to hearing a noise then I put it out again. There's no mark to guide my self.
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
The actual drive shaft going from the transfer case to the front differential? Is the shaft round on both ends?
@ezboyrc553
@ezboyrc553 3 жыл бұрын
I'm about to change a fuel pump on a Dodge just like it the fuel pump in it works but it just cranks over a ton in the mornings like it has no prime and after it sits for about an hour it loses all fuel pressure it has to crank over a bunch to start again. Does that sound like a few pump issue?
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
Likely the fuel pressure regulator, which is built into the pumps on these trucks.
@ezboyrc553
@ezboyrc553 3 жыл бұрын
That's what I was figuring. thank you for your time and Quick response. great video by the way
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
@@ezboyrc553 You’re welcome, good luck!
@sucsuc4dorra431
@sucsuc4dorra431 Жыл бұрын
Does anyone know if the filter is built into the pump
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
Yes the only filter it has is the little sock that goes on the bottom of the pump.
@donaldcook6997
@donaldcook6997 2 жыл бұрын
there are two lines on tank and an arrow on pump.. arrow has to be lined up to be between those line for fuel gauge to read right.. but you can take the huge housing off and replace the filter and pump,re assemble housing then reinstall and save over $100.. but hey maybe you're in a hurry and have more money than time.. so do it his way
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Yeah I usually just do the entire assembly so I don’t have to worry about possible faulty wiring going to the pump from the new pump to the hat of the assembly
@sethzimpleman4661
@sethzimpleman4661 3 жыл бұрын
I have an 04 qc with the 24 gallon tank. It’s saying these pumps are only for up to 03. Can’t seem to find any for an 04 24 gallon tank
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
I swear my 02 was also 24 gallons so I’m not sure what they would have changed to be honest
@sethzimpleman4661
@sethzimpleman4661 3 жыл бұрын
@@TonyTheTruckGuy I figured it out, they call it “crew cab” not quad cab
@meatsquadren
@meatsquadren 2 жыл бұрын
thank you
@meatsquadren
@meatsquadren 2 жыл бұрын
thanks to you i swapped out my old fuel pump in record time ! i wanna do heater core next any suggestions besides cap it and make some kinda custom electric?
@didsombodysayskip
@didsombodysayskip 4 жыл бұрын
Smart using gloves, no fingerprints for future endeavours. How does it sound with the cherry bomb?
@JAG77productions
@JAG77productions 2 жыл бұрын
If you back to your video you will see you pinched the gasket it didn't make a complete seal. Fyi also looks like you need an input shaft seal on the yolk to rear end.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Lmao yeah, the tank would leak if I filled it above 3/4, then I rewatched the video and saw the gasket got pinched 🤦‍♂️ And the yoke seal did eventually get done, but now the truck has gone to the scrapyard due to cancer.
@jett1277
@jett1277 10 ай бұрын
Would taking off the bed be better ?
@TonyTheTruckGuy
@TonyTheTruckGuy 10 ай бұрын
Depends how easy your bed mounting bolts come out and if you have a way to slide the bed back or lift it off without damaging it. If the straps are rusty and need replacement anyways then I’d drop the tank.
@eliezerrivera8764
@eliezerrivera8764 4 жыл бұрын
Thanks 👍👍👍
@danbranch5798
@danbranch5798 3 жыл бұрын
Just a thought. Wouldn’t it be easier to take the bed off? To change the fuel pump.
@lyricsforlife5090
@lyricsforlife5090 3 жыл бұрын
Not how the pump sits on this cab and bed style. Pump doesn't sit far enough back to just cut hole in bed/take bed off. Sits right under back seats so you have to drop tank
@danbranch5798
@danbranch5798 3 жыл бұрын
@@lyricsforlife5090 It does not sit under the backseat.
@lyricsforlife5090
@lyricsforlife5090 3 жыл бұрын
@@danbranch5798 yes it does, I should know. I just replaced mine on the 2001 quad cab. The fuel lines that go into the tank sit in the gap between the bed box and the cab. The actual fuel pump however, sits towards the front if the vehicle about 1 foot from the fuel IN lines, under the back seats.
@danbranch5798
@danbranch5798 3 жыл бұрын
@@lyricsforlife5090 Argree to disagree. A real plumber uses copper. Any two bit no papers guy can do plastic pipe. It takes skill to run copper. And its better quality.
@lyricsforlife5090
@lyricsforlife5090 3 жыл бұрын
@@danbranch5798 huh? Copper? What?
@bullockmike84
@bullockmike84 Жыл бұрын
I confusedon which pump I use
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
I recommend factory pump if you can afford it and plan to keep the vehicle, otherwise just get whatever your got parts store has on hand.
@rcmc1256
@rcmc1256 4 жыл бұрын
I have the same color set up Dakota with the same tow mirrors😂😂 I just have a few more stuff on it but nice video man👌🏼👌🏼👌🏼👌🏼
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Haha, nice style 😋 Thanks man!
@rcmc1256
@rcmc1256 4 жыл бұрын
Tony The Truck Guy I JUST REALIZED YOURE THE ONE I WATCHED TO PUT MY TOW MIRROS ON 😂😂😂 I commented and everything lol definitely subscribing you got good content my friend👌🏼👌🏼
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Lmao, I kinda thought your name looked familiar, but with so many comments it’s hard to keep track. Thanks man, appreciate it! I have a decent amount of videos for repairs, upgrades, tips on the Dakota.
@rcmc1256
@rcmc1256 4 жыл бұрын
Tony The Truck Guy definitely be checking those thanks brother stay safe.!
@Fkidd702
@Fkidd702 4 жыл бұрын
@@rcmc1256 where'd you guys get those mirrors?
@kylecardillo8552
@kylecardillo8552 3 жыл бұрын
Ever remove the bed? Bolt Count?
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
I have not. 4 main bolts for sure coming from the top inside the bed. Don’t think you have to remove any back by the bumper but there may be some electrical connectors or hoses attached to the bed.
@justinburchett6756
@justinburchett6756 4 жыл бұрын
Can’t get mine to even start now after a brand new pump and new starter
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Does it crank and just not start?
@justinburchett6756
@justinburchett6756 4 жыл бұрын
Tony The Truck Guy so honestly I’m new to this shit, and it kinda starts then looses it. Took the twist cap off the top when I dropped it a second time cause I noticed my buddy put it on cock eye. I could here it priming, battery was fine on voltage, put the new starter in after old one crapped out when we dropped the tank the first time. Im gonna re connect it today or tomorrow with some help and make sure everything is well connected. I just can’t figure out why the hell it won’t start and stay up. I can see voltage drop When trying to turn it over
@user-tm9xx5xs1o
@user-tm9xx5xs1o 3 жыл бұрын
Mine has a plate attached to the frame on the front side of the tank and seems like it’s not supposed to come off
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
Is it maybe just a skid plate?
@user-tm9xx5xs1o
@user-tm9xx5xs1o 3 жыл бұрын
@@TonyTheTruckGuy possibly. I’ll send you pictures tomorrow. Did yours have one the first time? You changed yours and you didn’t put it back on or?
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
@@user-tm9xx5xs1o Mine never had any plate, just the real thin tin piece that’s basically a heat shield to protect the tank from the exhaust which you can see in a few clips here. But your truck may have come with some skid plate package
@user-tm9xx5xs1o
@user-tm9xx5xs1o 3 жыл бұрын
I can’t add a photo so I’m just gonna try to go with it. It’s hanging down far enough now. Thank you so much!
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
@@user-tm9xx5xs1o Good luck!
@parrishmooneyham6095
@parrishmooneyham6095 4 жыл бұрын
Hey gents, quick question, at about 11:29 in the video, when you pushed the pump into the tank, the gasket went into hole by your left hand. Is the gasket supposed to set over the lip of the hole between the lip of the pump and lip of the hole? Or is it supposed to sink in between the body of the pump and wall of the tank? Was just curious if you have any vacuum/pressure issues due to that gasket sliding in with the pump as you put it in. Thanks in advance.
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
That’s DEFINITELY why has leaked out if I filled the tank over 3/4 after I did this 😂🤣 I didn’t notice that while doing this in person. The seal should be pinched between the lip of the tank and the pump collar, NOT pushed into the tank as you saw.
@parrishmooneyham6095
@parrishmooneyham6095 4 жыл бұрын
@@TonyTheTruckGuy Thanks dude, I thought so, my daughter has a 1997 Dodge Dakota extended cab, I'm sure it's similar in nature to yours. but wanted to verify.. Thanks for the clarification... and sorry you had that issue.. hahaha (sorry I'm not really laughing... ahahahah ops sorry).. ;)
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
@@parrishmooneyham6095 It’s funny thought because I never actually noticed that and I was wondering why it leaked lmao. Never pulled the tank back down to check, just didn’t fill it beyond 3/4 😂
@parrishmooneyham6095
@parrishmooneyham6095 4 жыл бұрын
@@TonyTheTruckGuy ya, i'd probably do the same, but being this is my daughters first vehicle. It was a farm truck and it LOOKS like it but hey, can't beat it for 300 bucks. ;).. BUT I'D have to pull it off again and fix cause I KNOW she wouldn't remember to only fill 3/4 tank.. hahahahaha But seriously the video is VERY informative and appreciate that.
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
@@parrishmooneyham6095 Best of luck!
@chadbrunson4792
@chadbrunson4792 4 жыл бұрын
Mechanic just quoted me $700 for this job fuel pump and two straps , I want to do the job the only problem is removing the straps the bolts are hard-to-get get at severely rusted on not sure wiser just to have the mechanic deal with it and have the parts warranty in case the fuel pump fails and have to change again
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
Yeah, it's a toss up. You could get a new pump with new straps for probably $300 if you to the work yourself. So I guess it depends how big of a deal $400 is to you haha
@keymctvreactz23
@keymctvreactz23 4 жыл бұрын
Where did you get your rear view mirrors on the truck from?????
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
You mean the tow mirrors?
@keymctvreactz23
@keymctvreactz23 4 жыл бұрын
@@TonyTheTruckGuy yes 🙌
@TonyTheTruckGuy
@TonyTheTruckGuy 4 жыл бұрын
@@keymctvreactz23 They require modifications to the door to make them work, but I have an install video here with product link in the video description - kzbin.info/www/bejne/gHrXiHZ7gdF6i8k
@keymctvreactz23
@keymctvreactz23 4 жыл бұрын
@@TonyTheTruckGuy thanks
@konasan
@konasan 2 ай бұрын
Well, the repair on the EVAP lines was easy enough. I cut the lines at the mouse holes and sleeved with rubber fuel hose and clamps. But the idiot engineers made the connection to the vent fitting out of unobtanium (a hose with different sizes at each end) so I had to Macgyver them out of stray hose and tubing parts. The sad part is once I got the tank back in (it was easy) I have no power to the fuel pump. I'm not gonna drop the tank again. Once I did it I realized that it would have save a lot of time and cussing if I had just lifted the bed.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 ай бұрын
@@konasan Yeah sadly it’s a double edged sword. Pulling the bed can go wrong too if there’s rust or if you don’t have a lift or some other guys to help lift or slide the bed. All comes down to preference and condition of the truck I suppose lol
@konasan
@konasan Ай бұрын
@@TonyTheTruckGuy You were correct. The bed was easy enough to raise with only 8 bolts and overhead beams with a chain hoist. And disconnect the filler pipe at the bed. But being a quad cab I couldn't get to the fuel pump (duh). So I dropped the tank. It was quick & easy the second time (no learning curve). The electrical connector at the fuel pump had been stretch and the ground pin had pulled out a bit. A pair of needle nose pliers fixed it.
@TonyTheTruckGuy
@TonyTheTruckGuy Ай бұрын
@@konasan UGH! Someone else did tell me the cab is in the way on the quad cabs and I totally forgot 🤦‍♂️ Glad you got it figured out lol
@crazeguy26
@crazeguy26 2 жыл бұрын
what he did to test the pump don't do that it hurts the pump as it running dry.
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Cycling the key? What else are you going to do?
@smid2550
@smid2550 3 жыл бұрын
The new pump should outlast the rust...
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
You would have thought, but it didn’t 😂
@smid2550
@smid2550 3 жыл бұрын
@@TonyTheTruckGuy Oh no! I'm in the same boat with my mom's '04 Dakota and I'm leaning toward the Bosch 67744
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
@@smid2550 Yeah, Bosch is probably a good choice.
@markboling162
@markboling162 2 жыл бұрын
Open a Dodge Dakota 1987 97
@Billfoote1959
@Billfoote1959 2 жыл бұрын
I got 2005
@TonyTheTruckGuy
@TonyTheTruckGuy 2 жыл бұрын
Different body style, so the fastener sizes and pump will likely be different, but I'm betting steps are similar.
@Desiludido79
@Desiludido79 Жыл бұрын
Aí nos estados unidos as dakotas são todas enferrujadas!
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
Los estados que se enfrían en el invierno y usan sal para carreteras para derretir la nieve y el hielo son las principales áreas de vehículos oxidados. Los estados más cálidos y secos son mucho mejores para los vehículos
@RobertlBradyJr-nl9er
@RobertlBradyJr-nl9er 10 ай бұрын
P😅
@calebhall7691
@calebhall7691 3 жыл бұрын
Why in the fuck is it that I type in my specific make, model, and fucking year of my Dodge Dakota and get every other fucking year. Rant over. Sorry guys
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
Because Google searches for the closest match haha. What year do you have?
@kevinlewis9151
@kevinlewis9151 Жыл бұрын
Your frame is junk my friend
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
Well, it’s been in the junkyard for a year now 🤷‍♂️
@kevinlewis9151
@kevinlewis9151 Жыл бұрын
@@TonyTheTruckGuy that explains a little bit lol you can come change mine for your next video lol
@TonyTheTruckGuy
@TonyTheTruckGuy Жыл бұрын
@@kevinlewis9151 Funny thing is the frame never failed, the front end just needed to be replaced for the 4th time and the cab mount collapsed due to rust. Still had some life in her but not safe and trustworthy as a daily driver.
@danbranch5798
@danbranch5798 3 жыл бұрын
Just a thought. Wouldn’t it be easier to take the bed off? To change the fuel pump
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
It depends. If the truck is clean and not rusty, and you have a means to lift the bed off, then maybe. This truck is pretty rusty and didn’t want to risk snapping the bed bolts and also didn’t have a way to lift the bed off, so just pulled the straps.
@danbranch5798
@danbranch5798 3 жыл бұрын
@@TonyTheTruckGuy My 2003 dodge Dakota It’s a California truck. No rust. I am going to try to lift one side of the bed. And hold it up with Jack stands. I am doing this by myself. I think it would be easier then dropping the gas tank by myself.
@TonyTheTruckGuy
@TonyTheTruckGuy 3 жыл бұрын
@@danbranch5798 It’s not too bad if the tank is close to empty, but if it’s full and truck is rust free then yeah you might be better off that way.
97-04 Dodge Dakota How to Replace Fuel Pump Assembly
25:55
martinbuilt
Рет қаралды 98 М.
How To Replace Fuel Pump 1997-2004 Dodge Dakota
11:50
Don’t Choose The Wrong Box 😱
00:41
Topper Guild
Рет қаралды 62 МЛН
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 23 МЛН
It’s all not real
00:15
V.A. show / Магика
Рет қаралды 20 МЛН
DODGE DAKOTA HEADLIGHT REMOVAL REPLACEMENT
9:04
BoostedMotorsports
Рет қаралды 137 М.
Top 5 Problems Dodge Dakota Truck 2nd Generation 1997-2004
7:37
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 699 М.
EXPOSED! My Customer JUST Bought This Dakota R/T and it's DOA!
18:30
How to Replace Power Steering Pump on a Dodge Dakota & Durango
15:34
Please DO NOT Buy a Dodge (Unless It Has This Engine)
10:26
Scotty Kilmer
Рет қаралды 879 М.
How To Replace Water Pump 1997-2004 Dodge Dakota
17:02
2001 dodge Ram fuel pump replacement
14:38
Jamey Willis
Рет қаралды 147 М.
100k Mile Service Dodge Dakota Truck 2nd Generation 1997-04
8:23
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 65 М.
Fuel Pump Upgrade | Dodge - Dakota - RAM - Durango | AEM 340lph
27:48
BoostedMotorsports
Рет қаралды 37 М.