Thanks very much. Goss bless u . Best Training , clear , slowly and instructive.
@user-gt4qc9yr4w5 ай бұрын
Useful lecture sir thank you very much
@AlfDot3 ай бұрын
Most welcome
@mohammadomar1558 Жыл бұрын
nice tutorial
@rezamagham44952 жыл бұрын
Good
@tarnumlordemmanuel82002 жыл бұрын
Can we control the speed using him instead of potentiometer?
@jobsinpakandgulf621 Жыл бұрын
nice to see can you tell me input 16 register hex no whr mention? undrestood output
@shridharnaidu66572 жыл бұрын
6RA80 ON PROFIBUS communicate ok but when start to download backup project shows error on BOP 33 & A01420. Pls help us.
@nelsonpantaleon77512 жыл бұрын
About network 4 drive speed did you scale analog input for 0 to 10 volt signal for iw 64
@AlfDot2 жыл бұрын
In this video no we haven't if you need any help how to do scaling contact me through mail
@nelsonpantaleon77512 жыл бұрын
@@AlfDot whats your email
@nelsonpantaleon77512 жыл бұрын
Its means just connect the potentiometer to the analog input 0-10 volts then select and thats it im right no need to scale so theres no limit the over/under shoot
@AlfDot2 жыл бұрын
Automationliftthefuture@gmail.com
@tarnumlordemmanuel82002 жыл бұрын
This hexa code are they same on all drive like eg altivar, g120
@AlfDot2 жыл бұрын
Same for siemens
@tarnumlordemmanuel82002 жыл бұрын
@@AlfDot sorry I mean I can use the hexa code to control altivar? Please can you also make videos on how to control altivar in tia portal using standard telegram, thank you
@huntersblue2 жыл бұрын
Why not use sina speed block?
@AlfDot2 жыл бұрын
In video we are showing in traditional way
@saadfuns Жыл бұрын
bro where i find the proper telegram with control word adress details
@AlfDot2 ай бұрын
images.app.goo.gl/7TbCQup3BgR3BpAj6
@abhishekgiri6907 Жыл бұрын
For the commissioning of drive first we use the starter of simotion software for allocate the PZD ...you only shared the half and incompleted information due to this many people will be distrub
@AlfDot Жыл бұрын
Here in this video we are giving how to communicate plc with drive and run the motor...pls check title if you want we will help you to do parameterisation by using manual...but you need "starter"or "IOP" or atleast BOP
@AlfDot Жыл бұрын
Plz check this video kzbin.info/www/bejne/pKDEmpieosijmtk
@surajharekar79283 жыл бұрын
How to start stop drive through profinet
@AlfDot3 жыл бұрын
images.app.goo.gl/pke5RfRmX9YfURNG7
@AlfDot3 жыл бұрын
Plz check with hexa decimal codes
@surajharekar79283 жыл бұрын
Need help
@AlfDot3 жыл бұрын
Contact me through the email
@saadfuns Жыл бұрын
send me your email id
@abhishekgiri6907 Жыл бұрын
Without drive starter software how can you run the motor
@AlfDot Жыл бұрын
Can you elaborate the question
@abhishekgiri6907 Жыл бұрын
Without optimization how are you running the motor And without drive software how will possible the optimization
@abhishekgiri6907 Жыл бұрын
If don't mind May i know your experience bandwidth?