PLC to Drive (VFD) Communication & Control with Standard Telegram

Siemens S7 1200 PLC to G120 AC Drive communication with standard telegram using Profinet/ Industrial Ethernet cable.
How to Control VFD Drive from PLC ?
كيفية التحكم فد من المجلس التشريعي الفلسطيني
Cómo controlar VFD desde PLC
如何从PLC控制VFD
Sådan styres VFD fra PLC
Comment contrôler VFD depuis l'automate
Wie kontrolliere ich VFD von der SPS
Πώς να ελέγξετε το VFD από το PLC
Come controllare VFD dal PLC
Как управлять VFD от PLC
For any more details please visit our below links.
1. Facebook : / automationrev
2.Twitter: / automationrevo1

[@dariodalmolin3862]

Thank you for this example!

[@Brian_Banda.]

thank you sir. i learnt so much from this video

[@pauln6130]

Great job on this presentation, got me out of trouble, thanks

[@AutomationRevolution]

+Paul Neurohr Thanks

[@vladislavkovachev6974]

Well done! Very useful tutorials. Thank you very much!

[@AutomationRevolution]

Thank you so much. please share as much as.

[@abdulkadher7455]

Thank you sir, very useful tutorials.

[@sureshg4196]

thanks lot sir, your helping many people getting knowledge about plc automation. good job. keep helping👏👏👏

[@svde1605]

Thanks... Can you elaborate which telegram for which vfd or based on user requirements

[@fernandocadena_]

Nice video!

[@rajasekarkrishnan1138]

Thanks you so much for this wonderful video. This video was very useful for me.

[@AutomationRevolution]

Thanks for your comments. Please share and subscribe

[@electeyes1698]

Thanks a lot blessings to you

[@user-ch1ep4hi7q]

thx

[@adembingol3387]

Thank you very much. it will be better also to make a connection with s7-1500 plc.

[@rajeshmandal6267]

Hello sir, What will happen, if we first run in forward direction and without stop it run in reverse direction?

[@sadeceibrahim3317]

this video is realy usefull !

[@AutomationRevolution]

Thanks. Kindly share & subscribe channel.

[@kiranchoudhari4717]

Sir please explain when we increase speed in HMI how PLC and drive communicate with HMI I mean in WinCC

[@farshadeissazadeh]

tanx

[@mohammadalhamali7321]

THANKS BUT FROM WHERE YOU KNOW THE SEQUENCE FOR WQ64 WQ66. THANKS

[@triminh8160]

Tks so much . you can do clip out profibus communication between s7-1500 ( or s7 1200 ) and inverter ... Tks !

[@theemployeedengineer9944]

Sir i want to communicate 6ra80 dc drive via ethernet cable , is that possible kindly guide me.

[@mohammadmobin6971]

Can you please share the complete control word list as you shown in telegram....

[@quench5424]

can i have excel-Table?

[@anshulkumar-kl4pr]

Sir please make a individual plc software and drive software after hiw to connect in pc and CPU through profinet or profibus then how to communicate please make video and share

[@pratik9057]

as i understand this is only control word in that exel can anyone tell me where can i find the status word i need that for run feedback

[@786Zachy]

Does the setting in the vfd and logic remain exactly the same... if I enter speed through hmi instead of physical Potentiometer ?

[@AutomationRevolution]

Yes, Only Speed factor will change rest of all logic will be same.

[@786Zachy]

@@AutomationRevolution Thanks. Appreciate it. But where is the speed factor setting ?

[@ajitkumarmohanty9533]

Sir in telegram current is not showing on monitor mode

[@sadeceibrahim3317]

I am curious about why you choose standart telegram pzd 1/1. Why you didn't pick other ones? Is there any hardware about telegram or its just as software?

[@AutomationRevolution]

It's just software package 1/1 means there are two tags will be used one as an Input and one as an output. Telegram is selected based on No of required IO.

[@GeneralKiller1337]

Hello, I am working with a Sinamics DCP CC-CC converter, using a S7-1500 with free tekegram. The only value I can set in the QWs is FFFFF, but I can set another value to the QW. How is it possible to change the value of a QW?

[@GeneralKiller1337]

Nevermind, i figured it out

[@NehalAhmedme]

can your please tell how do we know that qw 64 will point to the control work and qw 66 will point to the frequency command?

[@AutomationRevolution]

You can assign any of two word address for control or Frequency.

[@sharadtawade4027]

Sir, please upload the procedure for profibus communication between 6RA80 DC drive and s7-1200 plc. How they configure ??? Much needed.

[@AutomationRevolution]

Please check our video on DC drive configuration. we have already uploaded that video.

[@sharadtawade4027]

@@AutomationRevolution Sir, this video is with STARTER software I want to configure drive in TIA PORTAL with S7-1200 PLC. please help

[@ahmedrajput9351]

I will wait for your reply i have a sftware tia portal v 14

[@kohwenyi4130]

hi, how do i read data such as power consumption, current, voltage frm the vfd to siemens plc?

[@AutomationRevolution]

There are some parameters numbers which you can read or write with PLC. It's called Telegram.

[@kohwenyi4130]

@@AutomationRevolution Hi, I had read some documents. Is it by using the PCD or PZD parameter set at the VFD?

[@TT_S90]

When I double click on telegram I is not adding with my hardware system? How to get rid of this?

[@alpeshkumar8174]

i am facing off1 enable missing and speed controller inhibited

[@AutomationRevolution]

Check telegrame code property. watch video carefully and still you have problems , you can mail us.

[@DanIrooni]

I'm sorry, I have some problem understanding your dialect. What is Telegram (1)?

[@AutomationRevolution]

Telegram is one Facility provided by Siemens to communicate between PLC and VFD bidirectionally. You need to configure telegram as per control status word to control the VFD from PLC.

[@ahmedrajput9351]

Wao your videos are very good can you please prepare a video of analouge inputs and output using pressure transmitter 4-20ma or 0 t0 10 voltage and to control bit by arethematical instructions

[@AutomationRevolution]

+Ahmed rajput I have already made video on analog IO interface. Please watch PI tutorials.

[@ahmedrajput9351]

Sir if i am going to troubleshoot in any other industry and if i try to connect s7 1200 model so what is the procedure

[@kishorkumar401]

how can i give setpoint to the drive

[@AutomationRevolution]

Please watch video for that drive setpoint configuration. We have separately made that video.

[@youssefalaoui6894]

hello friend, i applied your methode carfully but i don't know why the motor doesn't run, would you enlighten me to solve this issue

[@AutomationRevolution]

Sir you need to configure drive first , Kindly watch basic configuration of Drive on this channel.

[@youssefalaoui6894]

@@AutomationRevolution hello sir, thank you for the response, concerning the drive configuration i just tried to move into automatic control by pushing the hand/auto, and the editing of those adresses that you mentionned in your video, if there is anything else please tel me,

[@youssefalaoui6894]

@@AutomationRevolution i don't configure the p700, is this can be the source of the problem, because it's value is 0, should i fix it at 6 as you did in the video??