Plumbing Rough In (Venting) The Building Expert 2021

Plumbing Venting Rough In Time-lapse (EP1) - The Building Expert - 2021
Here is a video of Plumbing Venting Rough in as per NPC of Canada.
If you have any question, comment or suggestion for a video please comment below.
Subscribe to our channel and be the first to know about new uploads.
Enjoy!
#TheBuildingExpert #RadiantHeating #Plumbing #Heating
AFFILIATE Links to tools used in the video:
Milwaukee Fuel Super Hawg: amzn.to/4bVuex2
Milwaukee 7 pc. Big Hawg with Carbide: amzn.to/4aYrM7v
Empire Level 12” Magnetic: amzn.to/4ciiJzh
Stanley Tape Measure 25’ amzn.to/4aZgQqo
Milwaukee Hackzall: amzn.to/4aZgSP2
Lenox Reciprocating Saw Blades, 25-Pack, 8” 18TPI amzn.to/3VErbmV
Milwaukee M18 REDLITHIUM HIGH OUTPUT XC 6 Ah Lithium-Ion Battery amzn.to/3XgRkcV
Milwaukee 2 Pack: amzn.to/3XgRuB3
Concept: Manvir Badyal
© Copyright 2021 The Building Expert (Manvir Badyal). All rights reserved.

[@TheBuildingExpert]

AFFILIATE Links to tools used in the video: Milwaukee Fuel Super Hawg: amzn.to/4bVuex2 Milwaukee 7 pc. Big Hawg with Carbide: amzn.to/4aYrM7v Empire Level 12” Magnetic: amzn.to/4ciiJzh Stanley Tape Measure 25’ amzn.to/4aZgQqo Milwaukee Hackzall: amzn.to/4aZgSP2 Lenox Reciprocating Saw Blades, 25-Pack, 8” 18TPI amzn.to/3VErbmV Milwaukee M18 REDLITHIUM HIGH OUTPUT XC 6 Ah Lithium-Ion Battery amzn.to/3XgRkcV Milwaukee 2 Pack: amzn.to/3XgRuB3

[@jasonjohn2355]

I had to leave you a comment/compliment here, the workmanship is obvious. Your drilling through the structure is very clean and precise. Nice work!

[@shaundonovan2193]

Nice work. Looks clean and neat.

[@TheBuildingExpert]

Thank you!

[@equaxion7597]

Very nice and awesome work! BTW what size drill bit do you use for the 2" vent pipe?

[@TheBuildingExpert]

We use Lenox 2-9/16’’ Self feed bit. Thanks for your feedback.

[@KhurramShahzad-s5s]

Nice to see I need to challenge red seal plumbing exam could you guide me for study material

[@gagenb4146]

Great work guys! You should buy a pair of 4" pipe cutters. It'll change your life!

[@TheBuildingExpert]

We have M18 Milwaukee Hackzall. Thanks for your feedback.

[@gavinbimbra7896]

@@TheBuildingExpert lol

[@adeadbodyman420]

A wheel does make nice cuts and straight in those tight spots that needs to be perfect. There is also no burrs or mess lol. I do use a sawzall too though.

[@TheBuildingExpert]

I agree, however hackzall is my go to when doing plumbing rough in!

[@charlesbucholz8079]

I don't use pipe cutters on PVC because it leaves a raised edge around the edge of pipe that has to be grazed off. Hacksaw or sawzall with hacksaw blade is best tool for the job.

[@rexdenemo5235]

Hi Folks, My eyes do not see so well, but vent pipes still get graded, and yes, they still get reamed before you chemically weld the joints. I could not tell if that got done. And do not forget the fire stopping. (On another video?) Respectfully, R.

[@Gerard1to]

Fire stopping is only when crossing between two or more different dwellings or units.. in the same room there is no need. Also, reaming doesn't matter for a vent.

[@JERRY_ONG]

Can you use wet vent? Save a lot of pipes.

[@TheBuildingExpert]

Yes for sure. In this video one of the sink drain is wet venting toilet & one is wet venting shower drain. Thanks

[@faucetmeaning6107]

Great job. Thanks

[@TheBuildingExpert]

Thanks. Glad you liked.

[@danielhoran4749]

never seen anyone pip from the bottom up lol. I was so confused on how the pipes were just sitting in the holes without falling down. Not even thinking about the possibility of someone piping from the bottom up haha. Wonder how well it works though.

[@charlesbucholz8079]

I couldn't even imagine piping from top down.

[@SheilaMaoMao]

Code not allow San tee on horizontal run. Use wye +45 degree turn on vent horizontal run instead

[@steventhury8366]

I believe a T is okay for vent.

[@Joe-jb9qu]

Question? Does the 2” dry vent pipe go all the way out the roof or can it be reduced to 1 1/4 or 1 1/2 per UPC? Trying to add a bathroom to my house but plumbing was the only trade I never learned 😅. Thanks

[@TheBuildingExpert]

Hi Jose Vent pipe shall extend undiminished in size above the roof. I Hope this helps.

[@Joe-jb9qu]

@@TheBuildingExpert Thank you !

[@charlesbucholz8079]

In Omaha, NE it must size up from 2" ...to 4" ...12" below roofline and 12" above roofline.

[@steventhury8366]

Must be at least 3" thru the roof.

[@WSRWSRWSRWSR]

Clean!

[@dan1417]

Somone needs to buy these guys a sawzall for real. nice work tho

[@ajsingh4406]

👍

[@Plumbgod1]

Bad singh

[@aldovaldovinos1465]

So many holes , you could easily connect them on top of all the 2x4

[@TheBuildingExpert]

We could but… A. If you look carefully @6:00 - 6:07 you can see a truss running parallel on top of the 2*4 wall. There is not enough space for a hole. B. Even if we had enough space we still had to make 4 holes in the double plates to run each vent into the attic space which in my opinion is the same thing. C. The wall is not load bearing so rather than running each vent pipe to the trusses, making holes in the studs saved us a lot of material. D. It’s less time consuming working in the studs than attic. Thanks for your feedback.

[@leach713]

Nice clean but I wouldn’t have drill through all those studs I would have revent two of them and then take them straight up and tie all of them to get in the crawl space or attic space , would have save you them time and fittings

[@gen.arnavpoe4633]

No slope....fail !!!!

[@richiecapuccino9853]

Vent pipe looks sloped to me

[@windywindy]

get your eyes checked

[@Californians_go_home]

A 2 inch pipe perfectly level has 2 inches of slope. A 4 inch pipe perfectly level has 4 inches of slope.