Doing a valve job on a budget with few special tools on this 1978 Tecumseh HS40 off of a Toro 421 snowblower Briggs & Stratton Valve Compressor: amzn.to/3vA2J7c Gasket Kit: www.ebay.com/itm/154367555322...
Пікірлер: 59
@Rein_Ciarfella Жыл бұрын
Doug, an easy way to cut a hole in the piece of sandpaper is to fold it into quarters and cut that inside corner off. Easy peasey! 😉👍🔧
@horserider95786 ай бұрын
Love the way things don't go exactly right things knocked over ect just the way it happens to me keep making them videos .
@johnbelliveau47043 жыл бұрын
Cousin Taryl ROCKS!! & there's your dinner !!
@HB-yq8gy2 жыл бұрын
You might be an amateur poor man but you’re rich at heart.
@myles52762 ай бұрын
This has given me some insight on my 1945 wisconsin so thank you very much.
@Adam-en4zm3 ай бұрын
Thanks for the video, this is gonna help me fix a snapped valve in my Onan 6.5kW marine genset. Luckily it has adjustable tappets, so it's a bit easier to get tuned up just right. I enjoy your videos, you got a sense of humor, and you speak to a fellow poor man mechanic, haha.
@philliphall5198 Жыл бұрын
That’s a good way to grind the stems Beats using a bench grinder for sure Good job 👏
@wannawin953 жыл бұрын
Last time I was this early, Tecumseh was still making engines
@shawngoldsberry7473 жыл бұрын
Was an engine
@stevemorris2493Ай бұрын
Good stuff! Keep it up! Update often!🎉
@outdoorsmansgarage3 жыл бұрын
Dang you sure are taking your time on it.... 😁🤘
@davidausburn15522 жыл бұрын
Hey bud, next time your lapping a under size valve just go grab one of the kids nerf darts. Works great
@DougvCarburetor2 жыл бұрын
WOW... That is an amazing tip. Wish I had thought of it. thank you!
@sccarguy82423 жыл бұрын
Another chunk of iron kept from the scrapyard. She loves to thump another day !
@marshallborder90893 жыл бұрын
Good job . Thanks for showing how too use the value spring compressior tool , I've done a lot of value jobs but only too use a screwdriver. I got valve spring tool given too me . ( yes the hard way I know) I'll comeback too your-video when I use it next time - for the first time .
@stanleyshults64275 ай бұрын
U never tried seat face in block,such a waste,also u need to update spring compressor,,can be done with one hand,spring remover,in less than 30 seconds
@dfields9511Ай бұрын
gr8 vid,, I think I am going to have to do this on a Briggs quantum 190cc on a lawnmower. It seems to loose compression when hot and will not start
@jesserousseau2481 Жыл бұрын
This is a great video.
@1stzjtruck7063 жыл бұрын
Very nice job
@JorgeVonVogler2 жыл бұрын
Sweet dude want to do this on a old Tecumseh eager 1
@kmweek2 жыл бұрын
That is really poor man dude, good video though. Good job.
@frankdavidson9675 Жыл бұрын
he got it running thats big
@eddymumford40863 ай бұрын
and there's your dinner 😁
@paulk53112 жыл бұрын
never saw anyone do a valve seat with sand paper. i have a small tub of valve grinding compound i have had for over 30 years and i have used not much at all. i just put a little on my finger and spread it around the valve seat then install the valve and spin it a few times then clean everything off real well and i am done. i bought a pinto back in 1986 that had a miss due to a valve leak. that is when i bought the grinding compound. i have done maybe a dozen engines over the years, mostly small ones like a motorcycle or atv or such. i have never had any issues with any of the engines i did. i have never used the rubber tool you twist the valves with either. all engines were overhead valve engines so i just took a drill and chucked the stem in it and spun it that way. now with a valve in the block engine obviously that would not work but i have yet to do any.
@kenbell95643 жыл бұрын
Wow, Where are your tools! Keep up the good vids! Ken
@suttonbogedain5874 Жыл бұрын
Thanks. Helpful.
@Kim-lc2uq Жыл бұрын
Usually find myself without the right fixit stuff or tools, glad I am not alone! Good tips on gittin er done, enjoyed the video, moved along nicely.
@philliphall5198 Жыл бұрын
Take a string and wrap around stem and work it back and forth It’s better than finger turning it
@robertgrauman86023 жыл бұрын
I remember when I lapped the valves on my 5.2 rebuild I watched a video where the guy described it just like you did but with the lapping tool. Only difference was he said to going until you hear the pitch change as you're lapping. Once you here the pitch change you stop and check the valve and seat. Repeat if necessary. Then again this could be the procedure for hardened seats.
@timzyaboi37843 жыл бұрын
Yea, that is a good rule of thumb when you have the speed of the lapping tool on your side. I do not think there is any issue with how Doug did it here though.
@robertgrauman86023 жыл бұрын
@@timzyaboi3784 I agree, I just don't know if the same rules apply to small engines and valve seats that aren't hardened.
@davidnadeau9460 Жыл бұрын
You should gap valves closer to the maximum tolerances 8 thousand inch rather than close to the minimum spec. The fact is it don't much matter if it clap a little, but matter much if the valves wouldn't close tight. And the other fact specially in exhaust valve is they expand with heat. And last on these tecumseh it's between 8 to 12 thousands an inch in the specs for both intake and exhause. 2 thousands is too tight maybe it's not the same engine specs but i would go closer to 8 thousand anyway since valve seat will use a little and get closer and closer, it will last longer at 8 thousand.
@frankdavidson9675 Жыл бұрын
never did use the wooden valve grinder sand paper is a no no need to grind valve and seat at same time with compound and wooden grindert ween both hands
@eddymumford40863 ай бұрын
i don't like the new head gaskets ... you can't take it back off
@kober211828 күн бұрын
What about the valve guides?
@lukek6492 Жыл бұрын
Hi. I have a very similar engine ... basically same one but newer I did a valve job on it. And now i am getting alot of oil coming out of the valve cover... Alot more then before any idea why thats happening.????
@solidjockey29633 жыл бұрын
Gotta make sure they are SGT spec! SGT = Standard German Torque = Gutentite.
@zanebeasley62468 ай бұрын
Enjoy the video
@RandomQualityGaming4 ай бұрын
I have one of these engines and it idles but it stalls when I accelerate. could the valves have something to do with it?
@eddymumford40863 ай бұрын
fire it up ... fire it up
@balanionut88632 жыл бұрын
Hii, are those mesure blades in mm? Could you tell me in comment what size should be the gap? Thanks a lot
@kmweek2 жыл бұрын
They are both metric and imperial equivalent feeler gauges
How much valve clearance for intake and exhaust valve
@jeffreyyoung41049 ай бұрын
I use .008 on intake, and .013 exhaust. The stems don't stretch, but the face and seat wear and the gap gets smaller.
@ethanshelton2763 Жыл бұрын
Get ya sone duck tape and cut ya a strip off ball it up with the sticky side make it about goofball size and you’re good to go works better then and hand valve
@adammosher58183 жыл бұрын
Can you do this with out shaving the valve
@J.E.Taylor3 жыл бұрын
No.
@adammosher58183 жыл бұрын
@@J.E.Taylor ok thanks for the info on it
@frankdavidson9675 Жыл бұрын
the valve and seat have form an air tight seal no leaks remember no compression with a leaky valve need take a comprssion check after you pu tthe head on to see if any leaks anything below 100psi is a leak prob.
@TheUltimate65 Жыл бұрын
Ohhh my gad,,whay not use the valvesanding tool...🙃
@squirrel1179 Жыл бұрын
You ever find yourself in that position again try a wooden dowl an some hot glue.
@brianp9115 Жыл бұрын
A “real” video
@kmweek2 жыл бұрын
Time to clean up that work counter of your 1 x 30 sander.
@robertbain26532 жыл бұрын
Why do you keep throwing things big turn off
@frankdavidson9675 Жыл бұрын
hes in a hurry to get thru with it .
@moderndaycowgirl92192 жыл бұрын
Not wd40
@rpiercebutler Жыл бұрын
my fathe rused to lap valves. All he accomplished is ruining valves and valve seats. Onan specificilly states in the manual "NEVER LAP VALVES" all it does is wear the valve seat and creates too wide a margin on the valve sealing surface.