Possible reasons why your Stabilitrak light is on in your GM

[@davidwashington8584]

Thanks for the awesome video my guy. Saved me some $$$ on my 2007 GMC Sierra now the inside of my truck doesn't look like a x-mas tree.

[@krismcraney5916]

This video just saved me such a headache, I shut my car off, pumped my breaks several times then restarted the car. All fixed, thank you very much

[@BlackWhite-ru8gm]

How did you reset your car?

[@scottieb483]

My light is still on

[@willsteele9249]

Thank you just happen on my 2007 Chevy Trailblazer I will update you tomorrow

[@brianlemere8596]

Thanks for the video Clay. I didn't complete the video and the brake pedal sensor was not the issue although it led me to my specific issue. Since I went to check the brake lights it led me to my issue. My issues were first start up of the morning the service stabilitrack would come on after about 500' out of the driveway and stay on until I turn the van off, Oh (2012 express 2500) and not any other times. I had this issue for about the last month. I also noticed in this time my right turn signal had an increased rate of operation. I found upon checking the brake lights that my rear left turn signal was out. Replaced and solved my issue.

[@sharpcarco]

That’s really cool thanks for sharing with us Brian I knew that it wasn’t the only reason for these lights to come on when I posted the video and I was hoping people like you would post the resolutions that they found so other people could be helped thank you very much have a great day

[@tstryker03]

My 08 silverado does the same thing but I don't have any lights out. Any guesses?

[@dave-o3674]

@@tstryker03 My mom just came to me with this same problem,... STABILITRAK I told her it sounds like traction control or maybe a differential problem.. Took my camera phone under her car looking for worn extremely rusty cracked or broken problems around the wheels Her brake fluid was low We filled it before checking under the SUV I totally know the video we just watched has to with his brakes, the brake pedal doesn't have enough pressure in the brake lines I think it was my old jeep with was a master cylinder problem years ago THE BRAKE LIGHTS STAYED ON EVEN WHEN PARKED... it might have air in it or leaking... but with my mom's Chevy Suburban I looked around underneath of it around the front wheels and a bolt was totally broke underneath The bushing and bolt broke off, It appeared supposed to be connected to the frame underneath closest to the ground.. I don't know what she ran over... But I said that's probably why..And told her to show the video to the mechanic.. The next day, a GM mechanic (GOODYEAR MECHANIC) said that was probably why the brakes squealed, she had been bringing it in her car asking why her brakes squealed at least twice before he said brake dust, today he said because the bolt was broken and it swayed so much, that pressure like the car leaning so much caused the brakes to loose fluid and also SQUEAL... AND HE CHARGED TO PUT IN NEW STABILITRAK SENSOR Yes he said he did put in a new sensor.. I SAID WHAT A NON WORKING BROKE SENSOR So today I started making a KZbin video since he charged to fix it and charged for a " new sensor" I told my mom, I didn't think anything was wrong with her old sensor, since that sensor let her know there was a serious problem, it even shut off her car when going down a hill with a curve at the buttom... So I guess the GM GOODYEAR mechanic just reset the sensor THEY JUST TELL THE COMPUTER TO IGNORE THE PROBLEM.. it's like that it even computer systems, they will run with a problem not being repaired at all, they just tell it to ignore that problem, IT MIGHT COME BACK ON LATER... But nothing appeared repaired It was fall break she had been driving the kids around WINTER IS COMING AND WELL HE CHARGED TO FIX IT YET DID NOT so I'm going to be posting a video about it in maybe a week, I hope the video can be about getting her money back

[@davechupp7922]

@@dave-o3674 This is how Big O Tires treat their customers. Shame on these people. This is an example why mechanics have such a bad reputation.

[@sharpcarco]

@dave not the 2nd I have no idea about big O , Well first off there is a dozen different things with your description please do not make any KZbin videos you were absolutely incorrect they cannot tell the computer to ignore something without paying $100 and having a tech to or maybe like an HP tuner . Or several other types of scanning devices that allow you to reprogram the ECM port to do that. (I will point out they can clear codes but they will come back within fivekey cycles) this is why I ask you not to make any KZbin videos because of what you said. I’m not trying to sound like a jerk. And if you would’ve sent me this message privately I would pretty much say the same thing and I would describe you what is wrong with all of your statements. I will however take in consideration that you are correct on a couple of different things but for the most part some of your statements make no sense. If you do choose to make a KZbin video, you do sound like the type of person that may inform yourself on both sides of the matter before doing that. Most mechanics make determinations based off of what the customer is telling them. And what the customer is willing to pay. If a customer walks into a store and says he can you take a look at my vehicle I’m happy to pay what it cost. More than likely they will do a thorough job If a customer comes in and ask how much does it cost to take a look at my vehicle. Most shops are going to see an hours worth of labor time . and they may find several things wrong and then tell the customer from the most important to the least important things to repair first. (In the situation they’re trying to be compassionate about the customers pocketbook not because they don’t want to do the work they just want their prices to be reasonable ) I am definitely not trying to throw shade at you. And I recommend you take your vehicle to another shop

[@gordonwoodard9153]

had some problems with the cruise control not working right .and abs light and traction control light was coming on and off on my 2010 chevy .when lights were on the 4 wheel drive would not work so i changed the brake light switch like you should and every thing works great thanks for the info and video

[@MrNuthed]

On my '11 Silverado it was the brake light switch. Dash was lit up like a Christmas tree, wouldn't go into gear and my mechanic told me that when I did manage to get it in gear that cruise control wouldn't have worked. I was thinking it was gonna be a wheel speed sensor. On a side note it crazy how much all that traction control, Stabilitrac and any other so called nanny features affect us. I spun out on a slightly damp road and went in the ditch when that switch went out.

[@techauto85]

As a fellow tech alot a people came into my shop with problems like this. Your video here was very helpful. . Thanks Clay.

[@sharpcarco]

Well then you obviously know that this is not the only reason that that light can be on and at the time that I made this video I thought it was one of the few reasons but I’ve learned over the course of a couple years . That it is several several reasons. So I’ve made a couple other videos on possible reasons why dislike can come on and I bet you I could write a book on them

[@techauto85]

@@sharpcarco on a 2017 model needed breaks but yes totally

[@techauto85]

Sorry buddy had to fix the typo.. talk to text sucks and I really didn't notice it.

[@davechupp7922]

I have a 2011 Buick Regal. Oddly, about the only time this Stabilitrak warning appears on my screen is when I'm leaving our local Walmart. There is about a 2 block drive from the parking area to the main road, with a stop sign in between. The warning goes off about the same place every time, yet rarely anywhere else. I will see if it goes off right after I take off from the stop sign. If so, I will stop the car and then see if the break lights are still on. If so, perhaps a little WD40 could help the problem? I am so grateful for this video. I had no clue before. Indeed, I hit Subscribe and a thumbs up.

[@tubekazo]

Buying too much stuff there :), try to leave empty

[@Thrallmack]

Clay I just fixed my heater hose. So I started driving the vehicle. It's a 2007 Yukon. The stabilitrak light came on

[@jrgroe332]

Thanks for the video but I've got a 2009 Buick Lacrosse 3.8L and for over a year my traction control and ABS lights have been on so they haven't been working. My friend (who's a mechanic) and I have been trying to figure out what is going on and replacing parts. The codes are C0090 & C0095. There was another code for the front left speed sensor and we took care of that with a new bearing. We also installed a new bearing on the right rear but that didn't fix it. While replacing that bearing he noticed the wires going into the plug from the loom was bad (not enough to splice) so I got a new loom that takes care of both rear wheels. As before that didn't clear the codes. We both decided to more research so I went home, lights on. When I got home I parked the car and then got the idea to start and see if the lights were on, they weren't. I went down the driveway (icy) and they ABS worked great and so did the traction control. But by the time I got parked back in the garage they were back on. He thinks since the ABS Control Module hasn't been working for so long the solenoid for that wheel may be stuck. What do you think? And any idea how to loosen it so it works? I've also read online that flushing the brake lines and putting in new brake fluid may work, again what do you think?

[@LH81633]

Jr Groe frade wire!!? Dirty abs sensor! Sensor didn’t get shimmed properly after brake job!! Dirty abs ring!! These are easy no cost solutions!!! Try them! It is said that replacing hubs to replace harness also and to replace in pairs!!

[@steve210sa]

Wheel speed sensor seems to be my problem also I own a 2010 Chevrolet Impala LT and constantly getting the Stabilitrac error along with a few other errors I can't recall at the moment.

[@robperkool28]

This might help someone, i have an 07 Silverado and the stability trac and traction control would flash on and say service soon then go away..... my fix was replacing the MAF sensor and the air filter, i also replaced the spark plugs. Believe it or not, the MAF sensor does infact have something to do with the stability trac issue.

[@wiskyd]

Dirty maf will cause a lean fuel condition which causes a misfire, anytime you have a misfire it disables traction control

[@brianrogers3489]

CLay, I've changed the brake sensor, ground wire from firewall to block. Stabilitrak and traction control off light still being displayed on my 2009 Silverado, really need another avenue before turning my 16 year old son loose in this truck.

[@tlcferguson8243]

Thank you I feel better now about my light thing lol coming on thank you.very informative

[@letsfly7562]

1:44 minutes of nonsense before you get to the point. People know to subscribe if they want to. We don’t need to be sold every video. Just get to the point of the issue. Good info just to long of bla bla bla

[@sharpcarco]

Yep but it’s a free video. I took the time make it. Please take the time to watch it. Sorry you did not like it. But thank you for the advise. God bless have a great day

[@tylergilbert2540]

Amen thank you well said almost 2 mins of bullshit

[@douglascheston1601]

Cut off the light on a 2008 Chevy Suburban stability light.

[@sharpcarco]

Well I honestly thought I had changed it I don’t know why I didn’t take it off of there but I’d appreciate it if you wouldn’t swear on my channel. Go somewhere else and watch another free video there’s thousands of theme I’m not the only show in town from what I’ve heard

[@jonathanmenjivar949]

I mean hes trying to help us out you know dont give him crap about it :/

[@tlcferguson8243]

Thank you fixed my problem, but didn't have to take out the switch.

[@bobbycanterro1685]

So what did you do exactly

[@masayagrigley9726]

So what did you do exactly

[@sharpcarco]

She watched the video I’m guessing.

[@tlcferguson8243]

Well I cant remember exactly because it was a couple of years ago, but as I was in the car waiting for my daughter to come out of a building, I KZbind it and up came clays vid about my Chevy, and just like that even I could do it. I think it was a fuse, or something small like that. Saved me a ton. Can't thank him enough.

[@codyroberts7993]

Good lookin out! Helped me a ton

[@estebahnrandolph8724]

There's going come a day where I'm going to RIP out all this crazy shit out my 2008 4x4 Silverado and put 400 in there and put mechanical kit on transmission and rewire this whole truck !

[@danishkhan-ob9ct]

I have jus restarted my truck and its gone😀😀. I felt relief .

[@michaelnewman89]

One wire on the mass airflow sensors plug was damaged on my 2010 Silverado. This was dangerous due to the fact that it completely disabled traction control and also my truck has the g80 locker that automatically locks . So let’s say it’s wet out and I’m accelerating on a interstate ramp. The truck will loose control because gm wanted to save money and use a outdated automatic locking diff instead of a selectable locker. Then found out oh shit this isn’t the safest thing so now let’s dump millions into developing a traction control system that keeps this from happening. And they still use it today.

[@claybartley7331]

There is a Service Stabiltrac message also its the enging ruff running and flasing engine lite..

[@LifeJourneyaboveandbeneath]

Great video

[@kilroy294]

My 2005 Z71 4X4 Tahoe has service stability and service brake on and most of the time it locks the brakes up. I can loosen the brake fluid lines on the front and the code goes away and I can then safely drive the vehicle. But now it will not go away

[@scottsigala2284]

Hello this is Scott sigala I’m trying to get a little help from you guys

[@flmcotriplet]

Steering wheel position sensor another possibility. Was down that road before..

[@mohamedelamin2595]

Very helpful , same problem and just noticed that the break lights are On Thanks

[@jeremysimmons2908]

Thanks Clay....

[@samtamo6428]

I got it fixed, in my case after engine change, they forgot (smh)to connect back the front right ABS cable, code cleared

[@jeffosborn60438]

I was wondering why this happened after I replaced my brake booster pump. I might have that switch in the right position

[@titts2408]

Thank you. Subscribed & look forward to more.

[@chrisjohnson-bw7mv]

my service stabiltrak an service traction control an my abs light comes an i replaced the steering wheel position senor an worked for couple days an its back on so it must be the part your talking about.

[@theemanofgodalexmartineziv5802]

I did tune up,new brakes,all new sensors,and new hub on one side I thought might be bad,checked all fuses and good still have stabil track and abs light with no check engine light.any ideas for me? Have a 19 GMC canyon with 67 k miles

[@dave-o3674]

My mom just came to me with this same problem,... STABILITRAK I told her it sounds like traction control or maybe a differential problem.. Took my camera phone under her car looking for worn extremely rusty cracked or broken problems around the wheels Her brake fluid was low We filled it before checking under the SUV I totally know the video we just watched has to with his brakes, the brake pedal doesn't have enough pressure in the brake lines I think it was my old jeep with was a master cylinder problem years ago THE BRAKE LIGHTS STAYED ON EVEN WHEN PARKED... it might have air in it or leaking... but with my mom's Chevy Suburban I looked around underneath of it around the front wheels and a bolt was totally broke underneath The bushing and bolt broke off, It appeared supposed to be connected to the frame underneath closest to the ground.. I don't know what she ran over... But I said that's probably why..And told her to show the video to the mechanic.. The next day, a GM mechanic (GOODYEAR MECHANIC) said that was probably why the brakes squealed, she had been bringing it in her car asking why her brakes squealed at least twice before he said brake dust, today he said because the bolt was broken and it swayed so much, that pressure like the car leaning so much caused the brakes to loose fluid and also SQUEAL... AND HE CHARGED TO PUT IN NEW STABILITRAK SENSOR Yes he said he did put in a new sensor.. I SAID WHAT A NON WORKING BROKE SENSOR So today I started making a KZbin video since he charged to fix it and charged for a " new sensor" I told my mom, I didn't think anything was wrong with her old sensor, since that sensor let her know there was a serious problem, it even shut off her car when going down a hill with a curve at the buttom... So I guess the GM GOODYEAR mechanic just reset the sensor THEY JUST TELL THE COMPUTER TO IGNORE THE PROBLEM.. it's like that it even computer systems, they will run with a problem not being repaired at all, they just tell it to ignore that problem, IT MIGHT COME BACK ON LATER... But nothing appeared repaired It was fall break she had been driving the kids around WINTER IS COMING AND WELL HE CHARGED TO FIX IT YET DID NOT so I'm going to be posting a video about it in maybe a week, I hope the video can be about getting her money back Here is the link to the problem i found I don't plan on fixing it myself, I do plan on having it fixed before winter time, AND I DO HOPE TO GET MY MOM A REFUND OF SOME SORT.. kzbin.info/www/bejne/l5OaqneZZ5iWnpI

[@LH81633]

Johnny on Dope if your brake lights are staying on!!! It’s the brake switch!!!! That’s the key diagnosing this problem

[@vettedon1]

Is stable link light also connected to compression in one cylinder? Two vehicles are doing this

[@valentinsanchez960]

my buick lacrosse 2012 has its annoying and very dangerous idk who design that way it should give drivers some time to find a parking before shutting down on it own

[@gnmozzzi]

Thanks for the great video Clay. It really sheds some light on my problems with my 2008 Chev. Equinox. I plug in my Actron scan tool and never see any fault codes when the stabilitrac light comes on. Do you think this brake light switch could be my problem also? What about the steering wheel sensor, as I have also seen video's about Chevy having problems with these also? Thanks for any help you can provide Clay. Have a good one.

[@lioness88amandaross82]

Also it doesn't matter if the road is wet or dry the traction control light and Stabilitrak still comes on

[@Native_love]

Actual video starts at 1:45, the rest is advertising.

[@mckevderby421]

Would this include 2008 Suburban?

[@claybartley7331]

Hey Clay ...this is Clay Bartley i have a 2 prong problem....i have a 2009 chevy tahoe which has stablitrac problem with a engine warning light ..The engine is running a little ruff...am just wondering if it may be a bad spark plugs or or bad plug wire ...or tire sensor..?

[@gladmarchatlein8164]

Hi The Clay Way... So was it this switch that realy causing the stabiliti Track,ABS and parking-Brake warning lights to come on in your truck ? I have a Captiva sport 2009 that's given me this problem.. I had a bad Rear Left-wheel sensor and tought this was my problem... I replaced all 4 sensors with bearing and still have the same problem with the Stabiliti Traction Control, ABS and parking-BRAKE ligth. Thankssssssss I'll have a look tomorow by replacing this switch and see if it will solve my problem. Thanks sir ! Regards.

[@SnowAmbassodors]

I put a lift kit on my truck and it tripped this issue wanted to know if you knew anything about what it triggered

[@darrenmann723]

My 2009 duramax 2500 has a stabilitrak error Code reader shows p07080 error transmission sensor a. I loose shift indicator light and it stays in whatever gear I am in when error surfaces. No cruise control. It has been resetting if you let it sit turned off but it's getting bad enough now I can't drive it. Error even occurs parked and idling. I'm frustrated nothing I've tried has worked

[@TomCrowellJr]

I had a bad mass airflow sensor.

[@TomCrowellJr]

2007 Yukon Denali

[@sharpcarco]

Yeah, after doing this video, I realized it could be a couple dozen different things that turn that stupid light on freaking General Motors

[@TomCrowellJr]

@@sharpcarco It was helpful. My cruise control worked wen they would go off so I knew it wasn't the brake switch.

[@troyglover9599]

sweet MATCO s6 box

[@sharpcarco]

Thank you only true gearheads appreciate something as beautiful as that toolbox !!!!🤪

[@troyglover9599]

I have Matco4s triple Bay in black with hutch and two lime green side cabinets. I think Matco has the best looking boxes out there !

[@preetsmoudgil4335]

start the video from 1.47

[@jamesbobreski9353]

Acadia Stablilink is this a poor design on GMC ?

[@georgechristian124]

How can I service the stabili trak for a 2012 gmc terrain

[@Bluegrassresale]

2010 camaro SS SERVICE STABLI Track comes on. Then goes off. Had it check said multi miss fire #3 cyclinder. Replaced #3coil all 8 spark plugs and #3 injector. But it’s still going it. Any ideas??

[@sharpcarco]

Good afternoon blue. Sorry to hear that . what size engine is in it. More than likely it’s probably the AFM valves are not working that would be my best guess right off the top of my head

[@Bluegrassresale]

6.2 L AUTOMATIC 64,oooMiles. It seem to mostly do it when turning and give it a good bit throttle. It will miss fore a little and the service stabi trak light will come on

[@sharpcarco]

Well why don’t you check out the throttle plate. And the air filter and make sure it’s not all gummed up. I know it seems silly and more than likely is not the problem. But heck it’s worth a try

[@Bluegrassresale]

I have cleaned the throttle body and MAF sensor . And replaced the air filter

[@staycalmandrelaxed5724]

I have a 2006 Denali that this light comes on almost half the time i leave the house and it will go off after i turn the car off and back on i wander if its the light or the car.

[@teritrahan4528]

My stabiliTrak light on and parking assistance. My car had sensor changed and it's still bad. Now it says po207 code

[@donaldjprescott886]

How do you know if the bright light switch is bad

[@LarsonFishing]

I have a 14 silverado and my abs and service stabilitrak just came on out of nowhere. All my brake system parts have been replaced and are new. Could me hard wiring in a 3rd brake light to my trailer package behind the bumper cause this if water, salt and other contaminants made it in to the soldiered connections? Thanks in advance!

[@sharpcarco]

Hey Steve the stability track light can come on for many different reasons I don’t think that is one of them what you need to do is have a shop look at the live data from your ABS system and they will be able to diagnose that problem really quickly Sorry I couldn’t be of more help

[@LarsonFishing]

@@sharpcarco First off thanks for the reply! Second - they are charging me $67 to read it on there scanner. Is it sophisticated enough to really pin point out where the issue is? Say if it's a ground somewhere. Will it be direct in the area of issue? I'm just trying to justify the money. Thanks again!

[@LarsonFishing]

@@sharpcarco ps Subscribed ! 💪

[@LH81633]

Steve L most of the time when those two lights are on together it’s the wheel hub,, always replace in pairs!!!!!! And it’s suggested you replace wire harness too! Moog comes with harness, however way to diagnose is if when driving it roars sounds like you have on 4by4, or lift of ground with jack turn wheel by hand listen for light grinding, shake wheel to look for any give!

[@LarsonFishing]

@@LH81633 thank you for the reply! These are both new hubs, roughly 5 months old. Replaced together. I am running 33s and these hubs are from the company Master Pro. Not reallycheap at $88 each. That's my confusion. Wonder if you strongly believe this, if I need higher end wheel bearing hubs? Again, thanks for replying 💪

[@dawsoncullinan635]

I domt know if you'll see this but have you ever came cross 4wd, stabilitrak and traction control going out all at the same time. My initial thoughts was wiring or actuator. Second opinion would be awsome.

[@sharpcarco]

Good morning Dawson, more than likely that’s just a bad wheel speed sensor. You just need to have it scanned and then you’ll know which sensor to replace that’s actually generally a pretty cheap repair

[@dawsoncullinan635]

@@sharpcarco thank you for the quick reply i will give that a try. You deserve your subscribers.

[@jasonhyde4081]

I have a question would that light cause my brakes not to work because at times I'll have great brakes so I know my brakes are good I just had a mechanic do my brakes my question is now that that light is on why is it at random times does it feel like I have no brakes at all

[@JoseMartinez-qx4je]

Does it work on a 2015 chevy silverado 1500

[@guerrar0597]

hi there clay I have a problem with a chevy 07 the stabilititrak comes on when braking an then off if you could give me a tip

[@sharpcarco]

More than likely it’s because your ABS wheel speed sensors are not working properly what you would have to do is look at live data while you’re breaking. I hope that’s helpful for you let me know how it turns out God bless have a great day

[@guerrar0597]

And how do i do that

[@guerrar0597]

Hello clay sorry to bother again but i cant look at abs live data with my scanner tool but it a has a code c0561-71

[@gyrene1966]

2012 Acadia w/approx 85K mi well maintained has recently been shifting into 4wd on the fly and randomly. Brought it into one of the few remaining Sears Auto Centers few mos ago where they changed the tranny fluid w/out disturbing filter/pan. Noticeable downshift and Traction Control Off, Service Stabilitrak, Service Traction Control and Engine Power is Reduced msgs come on as result. Thoughts please, thanks!

[@perryrobert9593]

Can the wheel speed sensor cause those dash lights to come on also. My a.b.s would kick in almost every time I stop so I pulled the a.b.s fuse and it still did it and now those lights are on. ( Fuse is back in)

[@sharpcarco]

Absolutely.... ABS can cause that in the past I found that that’s either a broken reluctor ring or a faulty ABS control module. Obviously I can’t say for certain and your situation because I’m not there and this is a text message but I would look at them two things because more than likely they are the culprit First thing you would do is watch on a live scanner all four wheels and see which one is going slower or faster than the other ones. Also having the wrong size tires will cause this problem as well they all must be the same size and the same make Because tires are just like jeans wranglers fit different than Levi’s etc. etc.

[@caifas08]

I drive a 2008 Silverado. I just hit a bump and the stabilitrak and check engine light pop out. But the engine now is making a knocking sound. Any ideas?

[@HulkSmash-dh7zf]

I get stabilitrak, no abs, no track control (lights stay illuminated on dash), cruise control works, and its intermittent. What can be the possible causes and ways of troubleshooting? Big help if you cover this topic.

[@deadloduggan3580]

I have an 07 yukon denali and the stabilitrak came on then check engine for p0011 still don't know what it is

[@GetIntoYourLife]

2015 Impala 2LT (stock) ,92,000 KM a few times a week, either at start or while driving "Service Stabilitrak" or "Service power steering" comes on. If the car is shut off for 5 minutes and restarted, those warnings on the odometer screen are gone. Ignore?

[@sharpcarco]

I’m not certain about that generally I have a Answer but in this situation that’s not something that I’ve ever heard of

[@GetIntoYourLife]

@@sharpcarco Maybe the brake light is staying on and screwing up the computer into throwing up stabilitrak stuff

[@1971chevyblazer]

2007 avalanche 4x4 lifted 8” I’ve replaced both front wheel hubs, with speed sensors and I only get the stability light when I make a turn right or left it don’t matter! No loss of power but I do feel a weak and slight pulse in the breaks!! I thought it was a bad wheel hub I bought from autozone so I upgraded and bought the high dollar moog ones and it’s the same issue Any suggestions would be helpful

[@sharpcarco]

Hey good afternoon custom that should be a pretty easy problem to fine when you look at the wires Wheel speed sensor wires they have to be pooled someway what you’re going to look for on the wires is a bunched up part they may not be tour but they will look almost kinked in a way. You could also look up how to do a continuity test and that will tell you where the break is that I am certain there is a break from what you’re telling me I hope you find it

[@jaredmartin3945]

did you find the issue ?

[@CCCROLLEY]

Is there a part number for it ? I have a 2011 Avalanche

[@edcampos99]

Hi Clay I have a 2016 gmc terrain with 130 plus thousand miles, today my stabilitrak light came on, first my dash needles started going up and down, then I lost power and my check engine light came on, I stopped turned it off and started it again, engine light still on, after a few minuted service satbilitrak light came on and loss of power, I was able to make it home, now my question is can it be the spark plugs? they haven't been change yet and would like to know if that can cause the problem. Thanks

[@sharpcarco]

Hello Edward ,There are several different causes of this problem and that most certainly can be one of them I hope that’s the case for you because that would be the easiest. I wish you the best of luck God bless and have a great day

[@sherryblack7282]

Had my front end replaced, now my stabilittrack, ABS and engine light on. What could it be?

[@kingkong8974]

Check the wiring

[@rayogamefarm3127]

I have the same problem did you find what it was?

[@groundshakersociety6637]

@@rayogamefarm3127 try checking and make sure they grounded the whole system.

[@fuhrersfarm9946]

Mine just did this after front end work anyone else figure out whT happend?

[@et8865]

Can you drive with the light on? Engine light flashing

[@sharpcarco]

That’s a difficult question to answer you probably have a misfire which turned on the stability track light and that misfire is pretty serious because they can clog up the catalytic converter‘s, more than likely you have a collapsed lifter it’s very common for the AFM engines. Obviously you haven’t giving me that much information but 90% of the time in the Chevy engine 2007 or newer it either needs a spark plug or it needs new lifters. However there is a way to bypass the AFM system but the lifter cannot be collapsed.

[@willsteele9249]

You were right the pedal does a lot is probably misdiagnosed thank you a bunch and for giving me the confidence that I could do it my self which I did😁 thank you again so much...

[@jadiel2543]

This was my problem maybe it would help.. every single time I disconnect my battery traction control comes on and it does not go away plus when I drive it it jerks on first or second gear not sure I have an automatic but I've done this methot twice and it worked for me I unplugged the positive and negative and touched them both to release every bit of energy the car has and left it unplugged overnight and plugged it back in the morning drive it to work and it was gone capish.. ur welcome

[@ceez1713]

I'm having the exact same problem now. Makes it drive rougher than normal

[@jesusalatorre9121]

I have the same problem

[@348frank348]

i have the same problem

[@Magnetica32]

I'm gonna try this. Thanks.

[@toddoppenlander8516]

Did this work? For all you that said you had same issues

[@tl97wings]

I've got a 2009 Buick Enclave. Stabilitrak message and cruise quit working. I replaced the brake relay switch, only $13 from a dealer. It fixed the cruise, but not the Stabilitrak message. Now what?

[@OgKushmedic]

Does anyones car turn off from it shut down completely then jump and it comes back on

[@nanashell21]

2015 acadia... rig runs fine...until the traction control and stabilitrak light comes on AND while accelerating, it struggles to send the power to the motor. The rig shakes..but only when it's an issue. Every time I start and drive it, it's fine. It happens at random. PLEASE HELP!

[@alexisoliveragalindo1480]

Shelly Ferris did you ever figure out what was wrong?

[@mariaevins2237]

Shelly.. this is happening to my Acadia.. did you find the issue? I've already spent $$$ and nothing.

[@farmerrobert5978]

Check spark plugs. Mis fire will cause

[@mariaevins2237]

@@farmerrobert5978 for myself .. this is one of the first things I did.. this actually happened again a few days ago .. after three months of everything being fine..

[@zaino660]

Code is P 2135, Throttle pedal position sensor, that's the problem.

[@Adamdub612]

I have my awd went off n my stabilitrak n brake lights are on so I'm wondering could it be this?

[@Adamdub612]

Mine is a 2008 Cadillac cts4 awd I have a feeling it could be this or corroded wiring from a leaking sunroof? I have a hard time attempting stuff like this

[@sharpcarco]

Well is any of your ABS lights on?

[@Deezey70]

Is there a easy way to HELP😉 the electrical system cause a uncontrollable fire in these pos trucks? Ive sunk just about enough time and money into mine and I about to drive it off a cliff

[@teritrahan4528]

Any suggestions

[@manuewiko17]

Hi Clay the GMC Envoy is making some noise like bad wheel bearing and the Stabilitrak light is on and off hopping is not the transfer case can I get your shop address so you can look at it ?

[@rich1953]

My stabilitrak light came on when daughter knocked wheels out of alignment, steering sensor generated code.

[@brandonhardin7807]

My 08 buick lucerne is doing the same thing wht do i do??????

[@dreywilson7792]

????

[@6BlackBetty6]

So the brake light switch was the reason the abs and/or stabilitrac light was on?

[@shainegoodrich9359]

My Stabilitrak and traction control light only comes on after a stop, within 1/2 mile or less it resets, any suggestions?

[@sharpcarco]

The possibility that comes to mind right away is that do you have a slow wheel speed sensor but I could not be for sure without hooking it up to a scanner. Meaning at slower movement the four sensors. One of them is towing the computer a different speed then the other ones

[@shainegoodrich9359]

@@sharpcarco I did replace all 4 wheel speed sensors, maybe one isnt spaced/shimmed at the right depth?

[@GammaProphet06]

Can some one tell me, why my stabikitrack come on as soon as I start my truck but when I put my foot on the gas it doesn't accelerate for a few min then it picks up. But when I put my foot on the breaks the breaks levitate.. I was told to replace my front differential but I was told that's not the issue can someone please tell me what the issue if u have a GMC envoy 2005

[@sharpcarco]

That’s a tough one to answer it sounds like you did the best job you could to explain it but unfortunately there’s a lot of variables that are not known so making a diagnosis over the Internet would be extremely difficult in your situation I wish I had better news and I could be of more help.

[@Romi.Frentescu]

It was a rainy day and my traction control and brake light came on and left headlight went out any tipe? Oh and that traction control and brake light turns on when i drive and turns off when i turn of the vehicle as long as i don't drive.

[@LH81633]

Romi Frentescu brake light staying on is key!!! Replace switch!!

[@SkyFisher-r1y]

My ABS and Stabilitrack keep coming on and off on and off

[@ParentalAlienationSupport]

Hi Clay. Both my stabilitrack and Parking brake light stay on, and I cannot use my cruise control. Could be this same issue, right? Thank you

[@sharpcarco]

Hey Chad good afternoon yes it absolutely should be but I can’t be for certain of course

[@MrNuthed]

Brake switch

[@bradtugboatodell9303]

Man0Man... Just get with the Repair...... Whew. Forgot what I was watching... 2+ Minutes

[@margostillo610]

Help so my traction control and stabilizer light come on then the abs came on and now my brack light what could b the problem im think just get a new car .

[@sharpcarco]

I doubt you need a new car Margot I just would recommend taking it to a local repair shop you don’t have to necessarily take it to the dealership and I’m sure it’s something that they can fix rather quickly my guess would be you may need a new wheel bearing or wheel bearing sensor but that’s just off the top of my head there’s so many possibilities it would be difficult for me to list them all

[@LH81633]

Replace brake light switch

[@daynawyatt8119]

Papl q

[@edselmartinez8879]

my chevy 2007 truck stabilitrak wont work but light doesnt come on i press the button doesnt shut on or off which confuses me. any ideas codes read u0109 but changed fuel control module u0121 lost communication with EBCM

[@edselmartinez8879]

DO YOU HAVE A VIDEO ON HOW TO CHECK THE POSITIVE AND GROUND CABLES THINKING OF CHECKING THAT FIRST..?

[@lioness88amandaross82]

My stabilitrak traction control light keeps coming in in my 2016 gmc acadia I have taken it to two mechanics do is put it on the computer to run Diagnostics. Nothing has came up it has said nothing about traction control Stabilitrak password when I get in the vehicle for the first time during the day and start it up it takes about 10 to 15 minutes before the light comes on but when I turn the car off the light goes out but it always comes back on also if I try to merge quickly into a lane it comes on and it feels like the car is skipping I don't know what else to do or I am thinking about taking it to the GM dealership I am at a loss for words I've been through the two mechanics that tell me there is nothing wrong that they can see or that the computer recognizes

[@elmonty_1812]

On my 07 suburban it comes on briefly, then goes off...not sure what it is

[@LH81633]

El Monty the Eminent some times it is a dirty air filter! Clogged fuel injector in wich they will fualt your spark plugs!! Check 1&7 plug regap or replace put in a very good fuel injector cleaner

[@rojannwerthmann4765]

My 2010 silverado 5.3 stabiligjt control & traction control light comes on--door locks lock & unlock rapididly--jumps into nuetral & back in gear--& engine revs---scary & might be dangerous --any suggestion on how to fix this

[@dronefootage7574]

Roger Ramjet that Happen to me and it was the ground on the battery

[@thomscott929]

Erik Gutierrez what all did you replace to fix the problem?

[@wesm353]

Hey Clay, I have a 14 Sierra Denali with a 6.2L. Today I popped a P0307 as well as the Trac Light. Why would they go off at the same time? The truck is idling and driving very rough. I'm going to replace the 7 ignition coil, wire and plug what should/can I do about the Traction Control light?

[@sharpcarco]

Take care of your own ability issue first and then see what happens there probably not related but they could possibly be on that new of vehicle.

[@wesm353]

Clay, Thank you for the replay. After carefully inspecting the engine I ended up finding the bank 7 spark plug wire was popping off. I replaced all the wires and it has been restored to beast mode.

[@sharpcarco]

Wes M That’s good to hear when we have comments like this. People generally read through the comments to see what other people pound and I’m sure that will be helpful for somebody in the future I’m glad you got the problem solved sorry I wasn’t of much more help

[@samba2238]

How to fixe Service stabilitrack GMC Terrain 2011

[@haroldcleckley6864]

Will this cause the engine light to come on an flash as well?

[@348frank348]

yea this happened to me too on a 2008 GMC Sierra. stabilitrak, abs, brake and engine lights came on

[@bottomofthemap696]

Well that is one possible reason. But not reasons

[@claudiocaraveslyng2155]

Hi Clay do you know something about crazy needles??. My unit is a 2011 Chevy Silverado HD 3500 6.6. When needles start to get crazy everything runs bad: radio, cruise control, A/C, gearbox, etc

[@sharpcarco]

This is going to sound stupid . But it sounds like your negative battery cable is probably loose or you have a bad ground there is something that is not connected completely together like it is supposed to be it may have been some kind of service that you performed in the past and the bolt not being tight is rearing its ugly head. Look for loose wires or loose connections I’m absolutely certain that’s probably your problem

[@stevenga69]

These trucks have a ground problem under the dash

[@teritrahan4528]

It's a SS CHEVY. I'm scared they are trouble shooting on my dime. I just want my car fixed

[@robertalexander7661]

I have a 2016 3/4 ton single cab, long bed. It's got 11700 miles. The service stabilatrac lite came on. Took my truck in to the dealer. They replaced some module, reprogrammed the computer. Brought it home. 8 weeks later, again. Took it back in, it's still there. Any ideas? Thanks for your help.

[@sharpcarco]

I wish I did Robert I’m sorry I can’t really help you with that without looking at the truck in person . Never hurts to ask though because you never know sometimes we learn these weird things

[@robertalexander7661]

Clay Rogers Hey, thank you for the reply!!!!

[@chicoroma495]

Hey clay I have a 2009 Chevy Tahoe my stabilizer track track control and abs light is on the engine seems to be a lil slow my front tire sensor has been out for awhile it also has been saying monitor tire system any suggestions

[@sharpcarco]

It definitely does not have anything to do with your tire pressure monitor unless your tire is just low all the time

[@dannyjarman4307]

could this maybe why traction control light is on and traction control not working on a 2008 pontiac torrent

[@sharpcarco]

Sounds like you probably have a bad wheel bearing very common with them vehicles

[@aliasgirl9]

I have an '08 torrent as well. Same issue with lights. I replaced my erg valve last summer but my lights are coming back on. From what I've gathered through my research today, there's four possibilities so far. I guess erg valves need to be a factory part. Next are the brake pedal switch, brake hub sensor or a grounding issue. All I know is that I don't know what check first and in what order. What is the progress of your vehicle?

[@jeffreyjones8756]

Did you ever figure this problem out?I have 08torrent and those lights are on and sometimes it’s stops driving