I just changed the port timing on a saw for the first time. Pcked up a 4218 crafstman strato for $20(that ones little brother). They sound like they are gargling under water for a reason. Carb venturi was only 9.5mm. Muffler was a maze. Intake and exhaust timing was 131 degrees . 70% of bore on the exhaust would put you into the muffler bolt holes. Drilled the carb venturi out to 12mm. Widened the exhaust as far as possible. Took exhaust to 152 degrees. Took intake down to bottom of piston with the ring just above exhaust port. Didn't even measure it, probably around 152. Can't widen the intake cause of the strato ports. The saw pulls much, much better than stock now. Easy saw to port, no plating. I doubt it took me 2 hours to tear it down, port it, and put it back together. I think those numbers are about the best for the saw. Shoot for 150 on the exhaust then take the intake down to the bottom of the piston with the ring right above the top of the exhaust port. Lowering the intake port as opposed to raising the skirt increase port volume but it straightens the port to intake block transition. Don't know if cutting the skirt would be a better option. The saw no longer sounds like it is gargling.
@autoair77326 ай бұрын
Interesting video mate. I personally use 325 chain on all my sub 60cc saws and 3/8 on 60cc + machines. Like you said that's the way things are in Europe and seems to work out just fine.
@frankz11256 ай бұрын
Porting it would probably make it run worse but a carb change would make a difference I bet. Cheers
@modarkthemauler6 ай бұрын
Buddy has the McCulloch version of that saw. The best part of the saw is the scrench in the handle. That's the special one that can be used to disengage the chainbreak if you manage to pry off the clutch cover with the break on. It started to run decent on the 5th tank.
@robertduncan2742Ай бұрын
I saw a post where a guy was doing carb work and a higher octane fuel. On one he changed coils for a hotter spark
@ragercrepair93016 ай бұрын
It doesn't run to bad for cheap homeowner saw. But it does need some fine tuning. Once you figure out the fuel issue I think it will be great for a ground saw to run in the dirty wood you don't want to run a good saw in.
@aaronpowell48856 ай бұрын
Thanks for sharing the part#👍🏻 I wrote it down when I watched your finding a .325 clutch video! Always wondered why they put a full size, full house 70dl 3/8 chain on them. I've got a couple of those pr5020's one mildly muffler modded and one stock, both run well, I want to like them but every time I get one out... meh. Figure if someone asks to borrow a saw they'll make fair loaners. Maybe not this week but will definitely have to order that sprocket and give it a try, may just change my opinion of them!
@aaronpowell48856 ай бұрын
Probably not but wonder if it could compete with a 450 rancher if ported🤔
@novicelumberjack6 ай бұрын
It would probably beat a stock 450 Rancher as it is with just the muffler mod and .325 sprocket. That is if I could get it to run perfect.
@Leo-tz6nq3 ай бұрын
I’ve got it in the European version called the CS50s. What I found is that the rod that connects the carb to the trigger is influenced by the pressure applied to the handle and it affects the carb lever. Also the carb might be undersized for what it should be.
@Super-Dave-Outdoors6 ай бұрын
I always thought Poulan was a french word for disappointment
@DaveyBlue326 ай бұрын
Super D! You know Pull-On! ,… is a south Louisian-a’ Word meaning…. Bad-To-The-Bone or Badazz! Hell man, Ol’ Jamie was the brother who designed and built the first Centrifugal pull-starter side covers that would spin out the chip debris and blow a positive charge across your air filter assembly! Which Electrolux slapped into the “Husqvarna” branded version’s and it’s what pushed them into a different professional user’s heart’s because they were just not near as bad at loading up their air filters and you found that you had a lot more running time then you could with your Stihl’s…. The hole Poulan engine design is a pretty near direct copy of what they called the 36-42…136-142…242…. Those little boxes are all the same …. I find it comical that you can get a Poulan badged 36cc and 42? Or whatever and they are all just the same stuff with different badges because of some marketing or engine size requirements by the government??? LMFFAO!!! We definitely don’t make shit in America anymore that’s worth a shit…. But that’s lazy people who want free shit and a lazy bloated government that will let them sickle from the big Tit! LMFFAO!
@ericfuller63264 ай бұрын
I always thought stihl stood for something uncle adolph special. Remember the boys on dday when you run that 462.🇩🇪⛓️🪚🟰🏳️🌈💩
@kalebbillig34724 ай бұрын
Actually it means; “PULL-AN’ PULL-AN’ PULL”
@ericfuller63264 ай бұрын
@@kalebbillig3472 and stihl stands for nazi trash saw.
@BBD403 ай бұрын
Yeah, my 4218 is a disappointment
@Witschor6 ай бұрын
Tank ventilation sucks often on these, leans out to scored Piston
@themanchannel87616 ай бұрын
Even though it's not running right, there is a noticeable difference, especially after the muffler mod. That tells you how choked up it was from the factory.
@bennyblanko34 ай бұрын
They are not choked up at all. It is an open can. Yea, a bigger hole flows a little better. But, they aren't way off stock.
@coolestguyontheplanet7236 ай бұрын
I would like to see that 50cc 😊ported against your wild thing or Peter Frampton
@bennyblanko34 ай бұрын
Mine ran like that. I ended up just buying a new carb, and putting a little motoseal behind the gaskets on both sides of the intake block, as it had a little air leak there. Also had to buy new fuel and oil caps as the original ones shrunk. Parts were really cheap - though I haven't looked in a long time.
@sirturdaloter141Ай бұрын
Stock sprocket and same muffler mod. I put a hotter plug in and tuned the carb. Try a hotter plug, that's what woke mine up with no dampening half cut.
@bennyblanko34 ай бұрын
Oh, and I can see the crappy super soft antivibe flexing a bunch when you are pushing on it. I think that if you push too hard it actually changes the throttle to the carb. I saw some guys just strap it so it limits movement.
@Special311980Күн бұрын
💪
@lonnieholbert88986 ай бұрын
If you feel lile playing with it some more, I went 160TD in and out and 20 blowdown on my POS 4218 and the turd absolutly came to life!
@coolestguyontheplanet7236 ай бұрын
Hey guys 😊
@Doc-Cole_Trickle-of-Chainsaws6 ай бұрын
😁
@tedneitzel6 ай бұрын
I actually think you would be a bit surprised if you did port it! Definitely did wake up with mm!
@driftlesshunter92006 ай бұрын
The newer Poulan chainsaws are quite disappointing. They're the perfect chainsaws for those who don't need to use one!
@Lilman30004 күн бұрын
Mines an animal with drilled exhaust and bigger spark plug gap
@robert40272 ай бұрын
who makes the best .325 full chizel chain please ? or 2nd best
@hillbilly4christ6385 ай бұрын
There is a lot of room in that combustion chamber at Tdc. If possible, a base gasket delete and or machining to improve compression. The rod may be really weak and not able to handle all that. Port the cylinder? These saws are so castrated that you have to do a lot just to get them to breath right. That filter is seriously weak, so remove the cover and put a bigger filter on it. I don’t see why you can’t get 5hp out of 50cc other than the overall quality of components.
@jackfrosty79ify6 ай бұрын
Older poulan 50cc saw rips
@philliphall51985 ай бұрын
Air filter ?? Check with several different manufacturers new ones
@jeremythiel25506 ай бұрын
I wonder if it's got a junk torch spark plug change it
@jasoncunningham67143 ай бұрын
A spark plug generally works it it doesn't even in a 500 700 HP v-8 makes like .05% power gain from the best plug to cheapest money can buy, just one mans opinion, peace
@lifebehindtheaxe38356 ай бұрын
Does this saw have the smaller fuel line that the 38 and 42cc have?
@robbevington17546 ай бұрын
Do common stuff for a common man saw
@philliphall51985 ай бұрын
Skip tooth chain maybe ?
@crazyfeller57046 ай бұрын
👍👍
@Doc-Cole_Trickle-of-Chainsaws6 ай бұрын
👍🆙BigGuy
@jeremythiel25506 ай бұрын
Intake mod
@robert40272 ай бұрын
Husqvarna owns poulin pro
@bryanfoxx22924 ай бұрын
Run a shorter bar.
@jonathanfierberg38076 ай бұрын
Dumpster food
@scottfoster24876 ай бұрын
I want to see 325 full skip on her.
@philliphall51985 ай бұрын
That’s what I’m thinking also 😊
@kingsaws6 ай бұрын
Looks like the same muffler as a 450 husqvarna.
@superdog19646 ай бұрын
That's because it is, Lol. Husky bought the brand awhile back and applied some of the X-Torq design into these saws. Besides, if every unit uses the same parts the overhead goes way down and profits go up?
@famasmaster20006 ай бұрын
C t b I d t h t w t t
@brandonsmith34476 ай бұрын
Okay Boedy. I know you got a taste of the dyno recently but please stop guessing at power numbers. You’re all about facts and real ass data. You’re not a dyno. Now saying that a saw feels like a certain saw is okay from Time to time but saying “went from 2.8 to 3.5….” Is silly. And lay off the Poulans brother.
@SnyderTechHD6 ай бұрын
Just let him be bro. If you’re mad about it, watch someone else. Lol.
@brandonsmith34476 ай бұрын
@@SnyderTechHD What’s that? I can’t hear you? If you’re not a lumber jack you’re just mumbling nuts son.
@superdog19646 ай бұрын
While it is rather odd to claim HP gains and amounts by just running a saw? you know that this information is just his opinion so no need to stress over it? Try this the next time it bothers you: Ask your mom for a mug of hot chocolate,take a deep breath, reach under your skirt and untwist your panties, take a deep breath and just try to relax. We both know you.enjoy watching people run a chainsaw,, otherwise you wouldn't be here in the first place. Take this for what it is? entertainment.I wouldn't do half of what this man does but it doesn't matter?. His video, time, money and saw give us both something to watch and enjoy. Oh yea before I forget, claiming to be a lumber jack gives you no extra credibility on the interwebs (even on a chainsaw video) then I can get telling you I am a psychiatrist/Therapist and you need to work on a few things. The longer we chat, the more I will know about your situation and the issues you face. A few sessions and the ability to watch a video without projecting your superiority complex in the comment section will happen. Life will get better! (And your mom doesn't hate you, honest!)
@sirturdaloter1414 күн бұрын
My Poulan PR5020 modded will rip any Stihl of the same cc in half. Ya'll are just shit at tuning small engines.