POWERBUILT 648604 upper control arm bushing service kit tool review

This is a tool review, and how to, with clips of removing and installing bushings with upper control arms that use an upper control arm shaft, and removal, and replacement of lower control arm bushings. Looks like the same set as OTC 7068
Disclaimer:
Due to factors beyond the control of Rust Belt Auto, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Rust Belt Auto assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this video at your own risk. Rust Belt Auto recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Rust Belt Auto, No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.
remove replace repair press-in service

[@chevynovaca]

Thank you for your AWESOME review video. Not only a good review, but an awesome demo and showing the tool in action. I bought the very same kit shortly after watching this video. Lastnight, pressed out the old bushings within minutes and no blood was shed. THANK YOU!!!

[@RustBeltAuto]

welcome!!!

[@brianholmes7883]

Thank you! You're one of the only people that made an actual video on how to use that damn tool. On my list to buy. Thanks again!

[@fwucku]

Thanks for the fantastic demo. I purchased this same set after watching this video.. thank you so much

[@RustBeltAuto]

😁

[@sonnybainto]

Very helpful video. Not too much blah blah, direct to the point. Thank you so much.

[@kjetilvalde2788]

Thanks for the great tool demo. Good to se a tool demo from someone who knows what they are doing. Ordering the kit now, 67 Impala is going to get some new bushings.

[@allenrider5810]

Rented this tool from Advance last week. Worked like a champ!

[@anthonythomas737]

Thanks for the video. You gave an outstanding demo of how to properly use the tool

[@jonrstinkton365]

Thank you! I’m sold!!

[@walterwolf2027]

Thanks for making this video, I just bought one of these kits after puzzling over a hydraulic press at the weekend and deciding to research it more before I tried. This stopped me from potentially screwing up an expensive set of Nolathane bushings!

[@MassiveTrackHunter]

Great tool! Gonna have to get one. Btw, the accent tells me your a good bit closer to the Canadian border than this Buckeye! Your accent brings back memories of family get togethers with our Minnes-oh-tans. :-) Love your videos.

[@glosshogg]

awesome tutorial, no BS...straight to the point with some handy tricks for good measure...thanks for sharing

[@wolleysegap9740]

That's a nice tool, Rick. Id keep it too. Also, they continue to put the sticker on the wrong side of the case.

[@RustBeltAuto]

I took the sticker off

[@ImTHATguy...]

Omg thank you! I guess I didn't know I could try to install without an attachment on the open C end and I was getting upset that my bushing was running into the tool because I didn't know what the hell I was doing 😆

[@jonathanazurdia5808]

Awesome video! Exactly what I was looking for as a buyer. Was looking for something like this to use on a C3 corvette upper a-arm. I can put away my air chisel now.

[@RustBeltAuto]

Thanks!

[@mrc5425]

Great Video! You made a tough job look easy.

[@socapots]

Great demo. Thanks for sharing

[@richardramon2175]

Thank you very much for your video. I own an 03 Tacoma and was dreading using other methods to remove and replace upper and lower control arm bushings. I am buying a used set from Amazon. I will let you know if it works or not.

[@Coodeville]

Looks to be a great tool. I have one that I bought years ago but I still have not used it

[@mebcool]

Yes sir, that is a very nice tool . . . Ok Bye ! Thanks dude. . . from Northern St. Louis County

[@masticobra6916]

Perfect 👌😍

[@bbiguino]

Saudações desde Portugal. Obrigado pelo video recebi há pouco o kit só falta experimentar, mas com a explicação fica mais fácil. Great job

[@dmccarty1006]

Nice tool..how much did it cost?

[@RustBeltAuto]

I dont answer how much, how long type questions.

[@mediaguy4037]

Rick doesn’t talk money. This was a sponsor.

[@dmccarty1006]

@@RustBeltAuto No Sake for you!!

[@RustBeltAuto]

@@dmccarty1006 next time someone asks me how much, I will just tell them to google it. Then I will get my own Sake.

[@MassiveTrackHunter]

@@RustBeltAuto XD XD

[@miguelmaldonado9881]

YOU GOT WEIRD AT THE END

[@robpaul7900]

You just caught the parts store in a lie they told you it was never used but there was dirt in the threads of the press.

[@RustBeltAuto]

No. It was an unopened package.

[@robpaul7900]

@@RustBeltAuto oh I thought in your video you said the threads had debris in them either way good video nice job.

[@RustBeltAuto]

@@robpaul7900 it came the way it did new, in an unopened package.

[@kdtxtooldad]

What is the tool you used in between the bushings?

[@RustBeltAuto]

It was either the control arm, or the rest of the tool.

[@julianarodriguez3635]

You just modify the tour

[@WOLFDADDY-O]

Tell me NOT...!

[@julianarodriguez3635]

Next time you silicon paste