Land Rover Defender 110 Side Square Plain Graphics / Badge Relocate

[@paullubcke8554]

Think less is more . Top looking defender.👍

[@AdyWalter]

Perhaps on the little section where you put the new badge, you could use the 110 logo on its side, similar to the bonnet graphic

[@L663]

Yes Ben is working on that now... I can see it on his computer

[@kevterseasta]

First video where you didn’t start with “right”. “Lovely” will do 👍🏻

[@L663]

Right I get your point.... crap i have done it again !

[@timskelton2125]

Safari themes..... Perhaps all the iterations of the model from 1948 onwards each getting bigger as they come down the graphic to the current models. Family tree with dates and the models next to it. That could look good if it’s a tree such as an Acacia.

[@darrenrobinson781]

Simon, can you not supply the same sized badge and adjust to keep it in line with the existing (covered by lunchbox) badge? If the plate or box is removed for any reason you have symmetry / alignment which will look better. Also Where have you got with the development rear bumper protecter from months ago? The one that went over the lip of the bumper to hive a bit of additional protection? I did follow up with your team (kate) in early April & was told it was in final development & 2 months away.. Is it ready yet 🙏

[@ianbarnard7682]

Great video. Couldn't you do a door pillar graphic with the ' 110 ' vertically ? Perhaps the original badge could be taken off and a blank square put there, leaving all the graphics on door pillar??

[@peterstewart6594]

Top tip : Applying graphics wet is fine, even better if you apply soapy water to rear of graphics as well, just don’t try playing with it for a couple of days to let water fully evaporate 😀 This way you can slide graphic into right position easier 👍 One other thing to remove graphic heat all over, keep moving heat gun and then use both hands to pull graphic of 👍

[@lucacecilia]

Would love a Red&Blue&White Union Jack for my Tasman Blue/white roof 110...I'd buy it in seconds!

[@daisyjohnsontv]

Would you consider doing a vinyl set for the side ladder steps? To essentially black out the silver chrome steps

[@philpassmore4922]

Would it not look better if badges were at the same level?

[@L663]

The idea was to use the badge relocate panel when you cannot see the original badge so its not that critical.

[@hap5121]

Do you have these square graphics in gloss & have them the full size of the panel ? So that they cover the entire panel with no color showing around the border.

[@TheGariuk]

I think topographical map graphics will look great. Something like they do for jeep.

[@ianb6375]

Simon is it worth doing a solid black panel to go under the lunch box etc and the badge can be removed or relocated to the door one? The two different sizes of badge location just look at odds with my OCD😀

[@grahamwest1079]

Surprised you didn't do sideways 110 on the narrow bit like the ones on the door

[@HQBProductions]

Graphic ideas!,...Some mountain peaks.....clouds....waves....”Gerry made me buy this”....a sheep/cow/horse etc..”Yes I do own a farm”....”Mud, mud, glorious mud!!” and maybe “I’ve been PowerfulUK’d !!” You will get loads of better ones!!! 😃😃😃😃😃Richard

[@rafflesnh]

"My other car is a Tesla" ;-)

[@snakeeyesman]

How about some old school Defender style full side body graphics?

[@midnightrun1256]

Hey do you have anyvideos on brakes looking for pads for front and rear rotors with bembos for 2018 range rover sport autobiography brakes

[@martin-vo4oj]

Hi guys. Regarding graphics I sent an email through to you with an idea for a three peice front stone chip protection kit for the FL2. I have the bonnet graphic fitted. It would be nice if you did produce the kit that it was made from the same material. Hope to see it on here soon.

[@L663]

Hi - yes I have seen that request and your sketch ... its on the list but bust with the new workshop for the next few weeks !

[@martin-vo4oj]

@@L663 Brilliant thanks for considering it. I'll keep an eye out.

[@promenteryrobbins]

You could maybe run an art competition to solicit some designs - offering a beanie for the top 10 design winners? …. Flags might be a popular choice (the Union flag of course, but flags of other countries where Defender sales do well. Words like « Defender, 4x4, 4WD, Overlander » might be interesting on the Window rectangle (vertical font). Lots of scope…

[@lucacecilia]

Would love a Red&Blue&White Union Jack for my Tasman Blue/white roof 110...I'd buy it in seconds!

[@L663]

We need to be careful with copyright.... DEFENDER is tricky..

[@poveysoatcakes]

What happened to George

[@L663]

Thanks for asking - George has just finished his exams and now has summer holidays so expect to see more of George again !

[@mattdavies3023]

Can you just remove those horrible panels full stop.

[@L663]

Apparently they just pull off !

[@mattdavies3023]

@@L663 that makes me want the 110 Defender even more.

[@mvirdi2333]

👍🙋‍♂️👌🙏

[@cosyg1379]

Please stop with applying vinyls wet. It will fail quicker than Landrover Airbags

[@L663]

Hi Robert - so far airbags and wet applied vinyl's are all OK - also you can see how well stuck the wet applied vinyl are.

[@cosyg1379]

@@L663 there can be tiny bits of water stuck under the vinyl, when it freezes they can crack the vinyl. If the vinyl has an air release carrier there is absolutely no need for water. Trust me I’ve been wrapping vehicles for over 20years. I must have had a bad Disco with the airbags 😂