Precision Plasma CNC table cutting an ornamental grate. 16 gage steel at 150ipm. Rapid speed is 1000ipm and acceleration is 50 in/sec/sec. Visit precisionplasmallc.com for more information.
Пікірлер: 103
@BoumanserviceNl9 жыл бұрын
Impressive feeds and accurate cuts by the way
@kleetus9211 жыл бұрын
Wow now there's a new chunk of information I never knew about plasma cutters...
@greenjeens13 жыл бұрын
Ya, those videos of the gantry traveling at those speeds were pretty amazing, never seen one move that fast.
@arowhead910 жыл бұрын
i made a large swordfish with my schools plasma cutter it is one of my favorite machines to use.
@elvis166914 жыл бұрын
You are correct. This video was made 20 minutes after assembling the table and it was accidentally programmed backwards. Cut quality is better if it is cut as you have stated, but it is still a good example of what a machine can do. Best Regards, Ron Chacich
@mayank131686 жыл бұрын
Sir can you provide this plasma metal cutting machine in India
@BoumanserviceNl9 жыл бұрын
Why is it touching the steel every second or third start when cutting ? Is this to set correct thc or measurement ?
9 жыл бұрын
Precision ? With ball bearing rails ? How exact is the precision please ? Great job !
@dude269914 жыл бұрын
I agree I run our CNC Profile at work and thats the direction it goes
@elvis166914 жыл бұрын
@Ebdan88 The thickness is based on the plasma cutter used. I use a Hypertherm 1250, which can cut 5/8" in a machine operation. Other plasma cutters can cut thicker material.
@matthiaskreidenweis7 жыл бұрын
Very nice Have you built the cnc part self?
@elvis166913 жыл бұрын
The cnc gantry has a resolution of .00098" or .0249mm per microstep of the motors direct drive as show or twice the resolution with the optional 2:1 belt reduction units. You would then need to look at the tolerance of the gear rack, but the biggest limiting factor for the tolerance is the plasma stream itself.
@gregstanley107511 жыл бұрын
Makes me want to get a cnc table for my powerplasma cutter.
@rocketlauncher9614 жыл бұрын
nice design!
@leopoldoalvarez67879 жыл бұрын
The power plasma set Amp was set up to....???
@elvis166914 жыл бұрын
@Fluidistor The plasma uses swirling air to make the cut, which makes it similar to a spinning machine tool. Because of the direction of the swirl, one side of the cut will be of better quality than the other. In this video, the edge quality on the part would have been better had the part been cut the opposite direction. Best Regards, Ron Chacich
@sheriffaroukfarooq89347 жыл бұрын
جامدة يا شيتوس ربنا يوفقك خسارة زعلتني
@friendhonour11 жыл бұрын
this is great.!!!
@jamshediqbal82976 жыл бұрын
Nice I like it
@automatizacionindustrialro68104 жыл бұрын
Amigo que plasma esta usando?
@charliemarks609611 жыл бұрын
I'd love to be able to CNC custom metal parts with my Everlast PowerPlasma. Do I need to change the torch?
@elvis166913 жыл бұрын
@flguy32501 This is the first prototype machine for Precision Plasma LLC 3 + years ago. It uses nema 23 stepper motors direct drive running sheetcam and mach3.
@afk21813 жыл бұрын
lollllllllllllllllllllllll ive just realised ive been watching plasma cuter and laser cuter for the last 30-40 minutes haha
@elvis166913 жыл бұрын
@greenjeens This video is of our first prototype machine 20 minutes after first turning on power. The motors are the Automation Direct nema 23 276 in-oz with a geckodrive and current setting of 2.7amps. Direct drive, it can easily achieve rapid speeds of 1000ipm and a acceleration rate of 50 in/sec/sec. The candcnc.com 300 or 620 motors will give you the exact same performance.
@rodicaxplod13 жыл бұрын
very nice!can you adapt a cnc milling machine in a plasma cutter? you only need a steel table and the cutting torch.is that right?!please answer.
@JimmysTractor13 жыл бұрын
Is this home made? NEMA 23 steppers? What CAM and controller software do you use?
@GunGemini12 жыл бұрын
i need one of these.
@greenjeens13 жыл бұрын
I noticed theres no gear reduction for greater resolution and torque, but it still cuts at a decent speed. I have seen your ads on ebay for this machine. In this video what motors are on here. I know there nema 23's but are they the 620oz version?
@kelliewood524511 жыл бұрын
Is the LTP a Lotos product? I'm not so sure about their customer support. I've heard good things about Everlast and I think they have a plasma cutter specifically made for CNC use. I can't remember the product model but I'm pretty sure it ends in a "C" to designate CNC use.
@1O1Matthew23214 жыл бұрын
Is the video shown in actual time or elapsed time?
@patanderson175911 жыл бұрын
What do you think the model LTP5000D on amazon and walmart? the review is really good.
@valveman1211 жыл бұрын
Hi does this plasma cutter have a pilot arc? I ask because it looks like the plasma head touches the metal before it cuts. Nice machine BTW
@syednadeem59139 жыл бұрын
What is price of this machine in uae ?
@dudeisboy11 жыл бұрын
I'm taking a welding class and we have a plasma cutter too, will the machine be able to cut a piece of metal that I'm going be putting around my cars plate number?
@bennyrlove9 жыл бұрын
when you cut small circles - put a common bolt size hole in the middle for washers which you can always use and cuts waste.
@bennyrlove7 жыл бұрын
ok
@Jarmezrocks5 жыл бұрын
bachelors of trolling degree, 2013 yeah but wastage man it's 2018 people need to conserve.
@janotosinnumeros13 жыл бұрын
i have no interest in machines and metal and stuff...but it's actually fun to watch a video like this
@SMG5913 жыл бұрын
i want one of these for christmas lol
@dogfightvj13 жыл бұрын
wow, that's how they do it
@elvis166914 жыл бұрын
The video is made in actual time. Thanks for viewing. Ron
@7727777777777778 жыл бұрын
You should post what kind of plasma machine your using. are you using a inductive start ... reg hf start or..Blowback start starts arc without the need of High Frequency
@willyjacobson17718 жыл бұрын
I've heard horror stories about people trying to get their high frequency plasma cutter to work problem-free with CNC computers. I've had my everlast blowback plasma cutter on my CNC for a few months now and no problems so far. I haven't seen too many plasma cutters using inductive start.
@fredalmond91308 жыл бұрын
Good to hear your everlast welder works with CNC. I hope to build my own this winter.
@maurizioperna418110 жыл бұрын
Bellissimo
@traileraxle7 жыл бұрын
looks good. what is your rail span?
@wilyon91656 жыл бұрын
Bobby Xie o8
@herrmc13 жыл бұрын
Are you willing to share your .dxf file? I really liked the pattern you cut out.
@hatemaltahir38687 жыл бұрын
Hello, I would like to know more about CNC plasma cutter, distributors in Chicago land area. Thanks
@tracywang747 жыл бұрын
@ Hatem Tahir. Hello friend, I'm Tracy, We are professional cutting machine manufacturer , Please contact us . My whatsapp: +86 15065325442 , I can send you more video
@MSaeedfab7 жыл бұрын
Hatem Tahir there are tons of cnc plasma makers in US. Do some research instead.
@ricocmg12 жыл бұрын
awesome.how much cost it in europe?
@misganawmekonen23745 жыл бұрын
How can I find different designs?
@Fluidistor14 жыл бұрын
Why is it so important to cut inside and outside CCW / CW?
@cjellwood13 жыл бұрын
I guess we are not talking 0.2mm tolerance here?
@omomjangid88635 жыл бұрын
Plz send mi all details size with price... Which material can be in this machine and how much can be in the thickness
@itiswhatitis16048 жыл бұрын
beutifulll
@rizkygunawan985711 жыл бұрын
I want to buy it but I don't have the money
@vipandhiman48672 жыл бұрын
Our requirement is to cut . 8mm to 5 mm MS Sheet kindly suggest best options of machines to fulfill this requirement..
@evazkee72466 жыл бұрын
The head movement should not go over a cut boundry. Just asking for a major crash
@mustafaok84017 жыл бұрын
How much is the price of this device
@gleguayogenuinegrindermaqu25515 жыл бұрын
Como puedo hacer una?
@anavaltierra586011 жыл бұрын
hello is it possible to know the cost of cnc plasma as well as their technical characteristics as well as you need to buy this product delivery times eg
@customfixation111 жыл бұрын
Im in he same boat.
@brentcapriotti258911 жыл бұрын
and good luck trying to keep there table square !! all the holes are slotted. i sent the one back i bought it was COMPLEAT CRAP !! they could not even get the machine to the cut process for me over the phone, oh and they have NO tech support! if any one has questions thinking about buying one dont !!
@maquinadesoldarautomatizac90137 жыл бұрын
Hypertherm is always better than Huanyuan LGK 300
@dimasvazquez17055 жыл бұрын
how mach is the price
@jahemkhan6446 жыл бұрын
How mach price
@tahirjawed847411 жыл бұрын
whats the price this machine
@sunilkumar-pg2qp5 жыл бұрын
Machine cost
@rajeshgowda53877 жыл бұрын
I want to buy this how
@muslimkhan-mu6wp6 жыл бұрын
Rajesh Gowda 9928388962
@mikefromspace11 жыл бұрын
I would say no. Precision, aside from having good tips in your plasma cutter, is a matter of how it's set, and how precise the cnc control is. I'm building my own cnc system for under 650 using 12mm ballscrew and 12mm shaft with nema23's direct drive, no gears or belts which still provides great tolerance on a 2' x 2' xy axis table.
@tahirjawed847411 жыл бұрын
kindly send me cataloger of machine ok
@vikyputra22383 жыл бұрын
Harga alatnya brapa boss
@riorumbewas39853 жыл бұрын
Cara pemesanan alat
@samakable14 жыл бұрын
From your video, The direction of cutting is not correct. inside should be CCW Outside should be CW
@Jarmezrocks5 жыл бұрын
What....51 people have no clue
@hemoofff30828 жыл бұрын
how much
@miayuan12388 жыл бұрын
+Hemoo Fff if you want to get a price ,please contact with me email :miyayuan928@gmail.com Cel:(+86)13475903996Skype:miya.yuan9Whatsapp&Viber: 008613475903996
@mustafaok84017 жыл бұрын
miya yuan How much is the price of this device
@ExposedChannel24713 жыл бұрын
Hi, I need a few pieces of 1/8" aluminum cut with plasma. If I provided the vector/line drawings, could you give me a quote or do you not accept this kind of work? Feel free to message me and/or provide me your e-mail. This is just a small job for a hobby/modeling project of mine.
@Levikyng11 жыл бұрын
i have bigger than this :D
@calpulz13 жыл бұрын
Lick it!
@maulanaafdil25383 жыл бұрын
q ......
@customfixation111 жыл бұрын
No it stays pretty square. Due to the fact it won't run long enough to get out of wack. The tech support literally called us stupid and said it was not there fault that the z axis runs all the way up and will randomly not cut stuff out. We have been on the phone with them for over a month trying to get the problem resolved but no success so we ordered a torch mate today. The jokes on them we are filming for a TV pilot at my shop and it will show the world what a piece of shit this set up is.
@brentcapriotti258911 жыл бұрын
i bought the 4x8 iplasma and yeah its the cheapest junk ive ever seen do not let the pics fool you. i sent mine back, it only cost my company tons of man hours for nothing, not to mention dealing with Ron and Jullian what a joke, there going to outa business soon im betting
@brentcapriotti258911 жыл бұрын
Precision Plasma has the worst customer service ever they do business with Tensor CNC LLC and he has super bad customer service I bought a table from them and they screwed me over