I'm using your brand kits and they are top notch...
@PrecisionReplacementParts5 жыл бұрын
Thanks Matt!
@joeltysver68113 жыл бұрын
Hot tip. Wear a long sleeve work shirt if you cut easily. Many sharp edges reaching inside the door. Good video.
@MARKWILLIAMS-tm4rf5 жыл бұрын
Howdy Jeff, thanks for the cool how to video! I own a 1988 GMC SUBURBAN and currently replacing both forward glass run(s). Glad I caught your vid especially the one bolt that when loosened the window is now to freely to move and able to install steering wheel side of run! Thank You MARK in So Cal.
@PrecisionReplacementParts5 жыл бұрын
Thank you Mark!
@afkaz4 жыл бұрын
This one actually helped.
@donaldmassaro72764 жыл бұрын
He did a real nice job I have done this before and trying to get my hands on those holes are big what a job it was
@coldhawk56659 жыл бұрын
Good job I'm gonna try it on my 87 short
@rhamer886 жыл бұрын
Great video, very informative. Thank you!
@donaldmassaro72764 жыл бұрын
On one other video somebody was asking why the tapping of the drums well it's at a critical point so once the glasses in plays the drums will quit that's my story and I'm sticking to it
@zanstuart28099 жыл бұрын
Why didn't you use any kind of weatherstrip adhesive? I'm asking because I need to do this to my own vehicle soon and I'm not quite sure whether or not I should use adhesive.
@PrecisionReplacementParts9 жыл бұрын
Zan Stuart For this installation we chose not to use any. We did use some adhesive in the video in this link: kzbin.info/www/bejne/gqS2c2eBlslnp6M Hope that gives you the clarity on using adhesives and bedding compound.
@VICD5057 жыл бұрын
awesome video man. thank you
@anthonyr.65657 жыл бұрын
You missed the part how you started the weather strip onto the top of the vent window, what's the metal tab for and how does it go in?
@68DerekC7 жыл бұрын
If you look at the top of your vent you'll see a slot towards one side. That tab slides in that slot which stops the glass run from sliding down. Hope that helps.
@anthonyr.65657 жыл бұрын
Derek C. I seen that little slot, but the rubber doesn't seat all the way down when the tab is inserted, and it's the lil slot that's facing the inside of the truck right?
@skwermotors4 жыл бұрын
hi, just replace the seals but when i roll up, the glass start to getting outside the channel. i have to pull it a little bit then it goes right. is there a way to fix this problem? thank you
@PrecisionReplacementParts4 жыл бұрын
Can you send us pictures at tech@prp.com
@badass49er18 жыл бұрын
is it possible to still install the weatherstrip without removing the 2 bolts to loosen the window? Thanks
@PrecisionReplacementParts8 жыл бұрын
Yes it is. Use glass cleaner to lubricate the back side of the run channel (not the fuzzy side). Also spray some into the metal channel itself. Insert the end of the run channel in between the glass edge and the metal channel. When you can't push any further, raise the glass glass half way and then lower again while pushing the run channel along with it. Keep doing this until seated down in the door in the correct position.
@badass49er18 жыл бұрын
ok thanks.. one last question.. should adhesive be applied all the way around?? Thanks again
@PrecisionReplacementParts8 жыл бұрын
No you do not need adhevsive
@keepcalm64557 жыл бұрын
what side does the metal tab on wheater strip face towards inside or outside?
@PrecisionReplacementParts7 жыл бұрын
The metal tab should go toward the inside. If you look at the top of your channel you should see a slot where that tab will hook into.
@rogerhess91236 жыл бұрын
Precision Replacement Parts o
@DCCustomDesign2 жыл бұрын
@@PrecisionReplacementParts Seems like it would be the opposite way. I don’t really see a tab. Brothers Truck install video shows it opposite from what you say…
@DCCustomDesign2 жыл бұрын
@@PrecisionReplacementParts hoping to confirm. I have to really put pressure on the window crank to make it go up all the way. That corner doesn’t seem like it’s making a good enough seal. A close up video of that installation part would be great!
@brookewoody86203 жыл бұрын
Can I get your stuff on Amazon?
@PrecisionReplacementParts3 жыл бұрын
You maybe able to find some stuff on there but probably not all. Send us an email if you need other options: info@prp.com