Problems that can cause low compression or zero engine compression/ 2AR FE engine!

[@itsbtunes]

Thank you, I've been looking for information about this engine. And this was the most complete and on point. Great video 👍🏻

[@valeriumoscalu7580]

You welcome! Hope it will be helpful for you!

[@valeriumoscalu7580]

Here is engine disassembly vide as well: kzbin.info/www/bejne/r4G5dY1nhsxkobM

[@PierrePatan]

Mr. Valeriu, thanks a lot for the excellent Class, we very appreciate your time and awesome experience

[@Denzar007]

Excellent knowledge

[@robertgriffinjr5250]

Thanks Valeriu Moscalu, Finally someone confirming my suspicions after 100s of videos on cam phasers causing low compression, especially running compression. As leakdown test was good and cranking compression was good, but misfires all on one bank on ford 4.6 3v. Guess next step is new mellings oil pump while im in there and timing components with good quality phasers.

[@vaaulichristopherpomare2220]

I just wanna say thank you for sharing your gift and may God extended your knowledge of being a great mechanic engineer. Where you from please?

[@valeriumoscalu7580]

Thank you Sir! Appreciate it!

[@shakcs6529]

Romania❤

[@mandarkumthekar8565]

Very informative🙏

[@valeriumoscalu7580]

Thank you!

[@rastabathu2526]

Thank you brother

[@valeriumoscalu7580]

You welcome!

[@AliAhmad-iy8sw]

Good explanation thanks. If you need any car engine let me know

[@vaaulichristopherpomare2220]

Thanks

[@valeriumoscalu7580]

Thank you Sir, I really appreciate it 🙋🏻‍♂️🧑‍🔧

[@Imtowavy]

Is it better to get the engine rebuilt or just get it replaced with another engine

[@DFWAuto_Hack]

What if the compression is too high such as spec 135 psi but test with 5 compression stroke show 225psi

[@panzerichi3837]

Will limp mode cause no compression In multiple cylinders? Please help😮

[@user-mb8kg4rg7z]

I have a Nissan na16 no compression on cylinder no 2 and 3 while the piston rings, cylinder head gasket and valves are new

[@valeriumoscalu7580]

You rebuilded the engine and after this it doesn't have compression?

[@valeriumoscalu7580]

This is how you do a leak down test if you have a tool: kzbin.info/www/bejne/rZizno2up9lmaq8

[@alem.naga21]

I have already spend so much money trying to fix mt car by the local mechanics. Changed clutch plates, rings and alot of electrical sensors trying to find the fault which causes low power of the car. I noticed, a little smoke and air coming out from dipstick when removed. What could be the issue here? Please respond 🙁

[@valeriumoscalu7580]

What car, what year and what engine?

[@alem.naga21]

@@valeriumoscalu7580 santro xing 2009 model, petrol engine

[@akaitv6606]

Upgrade it to a 2010-2012 mazda 2.5 , best upgrade ever .

[@vaaulichristopherpomare2220]

Valeriu can help me what to do please my car won’t start no compression it’s a 2007 grand Vitara Suzuki manual. What should I do ?

[@valeriumoscalu7580]

Did you use a gauge to test the compression in each cylinder? What does it show?

[@mark.r8900]

Hi, my 2007 audi a4 quattro 2.0L turbo stalls at a red light. The cam chain and tensioner broke. I replaced both with new ones. Now cylinders 1&3 have 150psi. But cylinders 2&4 only have 90psi. The car starts and runs but shaking like crazy. Can you please help me out to see what could be the problems? Thank you.

[@valeriumoscalu7580]

Did you inspected the cylinder head valves for leakage?

[@valeriumoscalu7580]

You should do a leak down test in this cylinders to see where it's loosing the air pressure!

[@valeriumoscalu7580]

The problem can be in the exhaust valves , intake valves if they have carbon build up and not closing all the way!

[@mark.r8900]

Ok thank you

[@cruisecontrol4400]

Hi what can be the issue if i have 80-90psi across all 8 cylinders, and timing is ok?

[@valeriumoscalu7580]

Watch this! kzbin.info/www/bejne/rZWum2Bul7WGbcU

[@ouwat4life]

I have low compression on one of my cylinders(100psi on cold engine). 2006 infiniti m45 4.5 v8. I dont wanna spend thousands to fix it. I was going to either sea foaming or throw a bottle of compression repair. What do u recommend i do first.

[@valeriumoscalu7580]

Do a compression leak down test first!

[@ouwat4life]

@@valeriumoscalu7580 Thanks for the reply. So the leak down test determines what is causing the low compression?

[@valeriumoscalu7580]

@ouwat4life leak down test will show you where you loosing compression through, and yes this will point you in the right direction ⬆️

[@iduajonye2280]

I changed my valves seals in my Mercedes c240 m112 engine. Trying to start the engine, discovered no compression. What could be the cause?

[@valeriumoscalu7580]

No compression in one cylinder or all of them?

[@angeljavier5320]

Just got a MK7 GTI and from nowhere the dealership saids the engine is toast because it didn’t have compression. The car was driving just fine and at the 7th day of ownership it just dies on the road and haven’t start again. It crank with very low power and you can hear her backfiring while trying to start. What would be the cause I replace spark plugs and one of my coils is damage it fall apart if you try to take it out. Also I can not hear my fuel pump but there is definitely a fuel smell on the engine while cranking. Any other options I can anything else? I do have 4 new coils I haven’t put on because the car is still at the dealership

[@valeriumoscalu7580]

Fuel and coils have nothing to do with compression! If compression is to low it will not start!

[@angeljavier5320]

@@valeriumoscalu7580 I know but does the symptoms are common of a no compression engine?

[@HonderdtachtigCC]

@@angeljavier5320 Have you found a fix yet

[@abdullahomar5339]

Can this cause a car not to move while the gear is engaged?

[@feitan8745]

transmission

[@dekacster]

what if all of 4 cylinder have only 3 -4 bar?

[@valeriumoscalu7580]

Than you need to check what is the cause of low compression and fix it! With compression so low the engine isn't going to run!

[@dekacster]

@@valeriumoscalu7580 yes, thats right, it is most likely not running, just bugging :/ kinda not really common problem, if i pour a little oil into the cylinders, it can reach a little more bar, but no so significant. anyways i have to disassemble it, just wanted to ask you opinion. thanks for the feedback :)

[@junglejuice23]

Are all of these issues preventable?

[@jubblybits6155]

Yup. Change your oil every 6 months or 5,000 miles even if the manufacturer recommends 10,000 mile oil change interval. Also never let your motor overheat.

[@Honda732]

Honda accord f18b2 1.8 vtec 1999 year three cylinders have a compression of 10,the fourth cylinder has only 4.5,the spark plug is black and consumes oil,works restlessly in reverse What could be the cause

[@valeriumoscalu7580]

Can be :intake valves, exhaust valves, piston rings, headgasket , piston, crack in the cylinder!

[@valeriumoscalu7580]

You need to do a leak down test to see where you loosing compression!

[@denisasenov3639]

Did you fix it? I have the same problem, first 3 cil running at 14/13.5 bar, the 4 one is 2.3 bar, i have done 9500 rpm on a 8k limiter car so i think maybe valves or piston damage

[@KooYang]

Geeez basically in order to fix the problem %100 is swap the motor.

[@valeriumoscalu7580]

Why to swap it?

[@DatHondaBoi223]

Or rebuild it lol way cheaper

[@waqasansari8283]

My bike tensioner stuck while in starting position. Then i instantly turn off my bike and reset its timing chain setting. But now bike won't start and no compression. Do you know the problem kindly help to figure it out?

[@valeriumoscalu7580]

Brobably the chain was looking loose and jumped a few teeth and now the timing is wrong!

[@waqasansari8283]

@@valeriumoscalu7580 yes but after this incident i set again timing chain setting and check everything even clutch setting. Both valve working properly but when i move magnet it showing no resistance and no compression realizing sound. It seems that piston cracked or rings are broken. So according to these inspections Sir what is your opinion?

[@valeriumoscalu7580]

@@waqasansari8283 are you Shure timing is right? If you miss a few teeths it can loose compression!

[@waqasansari8283]

@@valeriumoscalu7580 yes 💯 m sure

[@waqasansari8283]

When i kick start then kick has minor resistance or sometime kick has no resistance.

[@santiaggie]

😏

[@fatmirsejdini5992]

All incorrect. #1 problem is that valves are not closed due to over tighten of rocker arm

[@valeriumoscalu7580]

The lyfters here are hydraulic, they don't need adjustment! They are use oil pressure and a preload spring to achieve corect valve lash!