(Electric Tachometer needle bouncing fix) RPM gauge needle bouncing. How to fix bouncing tach

[@brianwick3826]

As someone in the middle of a 71 Corvette resto mod project, these videos are super helpful. Thanks, and keep up the good work.

[@ProblemSolverGarage]

Thanks and thanks for watching

[@age_of_reason]

I think you meant restoration.

[@pongo963]

First I want to thank you for putting in the time to explain things corvette related the way you do. My question for you is this. After driving I pull into the garage and turn the car off. I'll look at the Tach Needle and it will pin itself all the way to the right, at the 70. When I start the car and drive down the street it will correct itself and act normal. When i turn it off again the Needle jumps back to 70. My second question is this. Can you turn an original 350 motor into a 383 stroker? Waiting to see your answer.

[@allenvaughan1]

That was a brilliant solution! And I want you to know that I have enjoyed all of your videos! My 77 C3 needs a complete rebuild of its HVAC system and a new wiring harness with the newer blade type fuses. Because of your videos, I have the confidence now to take out the dash and do the necessary work

[@ProblemSolverGarage]

Nice 👍 and thx

[@AlaaMurtadha]

Thank you for sharing I have 1976 corvette , tachometer stopped working, I changed the board and the ignition coil and problem didn't solve. And advise .

[@ProblemSolverGarage]

Sorry dont know. Grounds?

[@AlaaMurtadha]

@ no

[@Moparfest_Robbie]

Excellent solution for a problem I’m currently having with my 1979 power wagon restoration. Any chance this would be the same fix for a fuel gauge reading empty when full? Too much voltage?

[@ProblemSolverGarage]

No I believe that would be different

[@ronstjohn6780]

When I first started watching this series I had some doubts this Corvette would get back on the road. But you have certainly proved me wrong. Thanks for producing these video😊😊😊

[@ProblemSolverGarage]

It’s actually already finished and on the road, just haven’t released all the episodes yet

[@edpetrikk2027]

Dude …How in the world did you figure this one out !!! I am going to watch every one of your C3 Corvette videos at least five times ( guess what car I have ) You young man ..are ..Da Man 👍😎

[@ProblemSolverGarage]

Thx 🙏🏻

[@MPSuwanee]

Great vid. I would never know to do that. I just want to get squeak out of my 79 speedo cable or speedo needle connection.

[@colewoodge]

My tach reads 700 higher than it should, key on 700, idle around 1500. Any way to recalibrate it back to zero at key on the way it should be?

[@chadportenga7858]

Depending on the year, there are several videos I've seen showing how to "Rezero" or "Zero" the tach. A quick search should find one.

[@rea8755]

Another great video. Thank you. I have a question: with the purchase of a c3 that runs...what would be my steps to checking out systems? Upgrading systems? I am so lost, but proud new owner.

[@ProblemSolverGarage]

Watch the whole series every episode in a row it will give you lots of ideas on how to do things and where to start

[@ProblemSolverGarage]

Go under playlist in my channel

[@ShaneOReilly]

I just tried this and its still doing it. Should i wire in a second resistor?

[@han.kievit2260]

What for wires going in the tach? I have a blazer k5 but my tacho dos not work at all…

[@JasonLee-lv7tm]

He literally just said what wires go there

[@1977rubper]

I recently installed a performance distributor on a 72 gmc and it started doing the wobble..how do I fix it? what would you suggest? enjoyed your video

[@tonyb1968]

Nice job 👍

[@ProblemSolverGarage]

Thx

[@ceesklumper]

Neat solution. The only thing I would add is soldering the connectors in addition to crimping them on. Those resistor ends are super thin.

[@ProblemSolverGarage]

👍

[@Phone-sh7jg]

Can improper level of transmission fluid cause that?

[@ProblemSolverGarage]

No

[@nicholasgill5236]

Do I need to worry about any other problems with my ignition coil?

[@ProblemSolverGarage]

If the car runs good and there’s no issues then no

[@anthonyrodriguez7639]

Thanks again You're just great I was able to fix it

[@ProblemSolverGarage]

Thanks for watching

[@JamesMullarneyIsAFraud]

brilliant bro! Thanks.

[@ProblemSolverGarage]

No problem

[@williamb454]

Is it possible to blow your tach? I think i screwed mine up!!

[@kevinjubinville5624]

Tried this today on my Harley, unfortunately it didn't work,I was hopeful,any other ideas?

[@ProblemSolverGarage]

Sorry not too sure

[@grinanbarreit8242]

why those dont come factory with a shielded signal wire is mind boggling.

[@JasonLee-lv7tm]

They do Called a tach filter

[@chrissmith7669]

Lol. At least yours works.

[@ProblemSolverGarage]

it does 👍

[@RobertAmine]

stop saying guys all the time

[@ProblemSolverGarage]

Hey guys, I will try to stop