Process Of Creating Cement Lego Bricks - Jointed Bricks Without Mortar

Process Of Creating Cement Lego Bricks - Jointed Bricks Without Mortar

[@lastsinner1738]

Why don't people use interlocking blocks and bricks for construction? Literally make them to where you can run rebar down thru all the walls and tie the rear at the top. Hell for that matter you could tack weld all the top ones and cut and reuse the blocks later. I have done construction and it seems to me there is a lot of extra work and money for less reliability.

[@Bob_Adkins]

Great design! Strong, foolproof to use, need no mortar. If you did use them in a building, just a tiny bit of concrete slurry, expanding liquid foam, gorilla glue, or construction adhesive would lock them very strongly. They could also be made cheaply with dustcrete or fired clay.

[@fabr5747]

The mortar has also the role to correct the irregularity of the bricks. No product on earth is precise. The mortar enables to correct it in order to build vertical walls, at the same height from one side to the other, and on the same plane. With only 2 levels of these bricks, you already sea irregularities, and they accumulate with the design, they don't compensate.

[@redtex]

Без проверки прочности это просто кубики для красоты.

[@Fatpumpumlovah2]

this is a good idea without waisting too much of each blocks height, easily fixed by makeing each block just a little bit higher than a normal block. and these overlaps the holes actually match

[@kaiwheeler64]

Those small inaccuracies are gonna accumulate on a larger structure.

[@carlosneira4801]

Hacen videos y no muestran medidas parece que fueran secretas 😅

[@diconicabastion5790]

They are fine if you want to create a flower bed wall or something like that. They won't work for creating a strong structure you need more room between them for putting wet cement to bond them. 1/3 to 1/2 of an inch should be good.

[@Sinlatown]

Couple hundred years later: "I finaly finish my 45m square house! Whooh!"

[@tonyHern865]

😂😂

[@breezewaycockers2558]

That's exactly what I was going to say. You can produce up to 365 bricks per year🎉

[@KirkDickinson]

Nice. Looks so cool. However the time required to create the blocks, you could assemble walls with mortar and save a lot of time.

[@zhandoskossakbay617]

Great job man.

[@adil012345]

Perfect interlocking bricks

[@codysalyer6212]

Might want some bigger tolerance in the bottom side so it can handle a little more imperfection in the brick laying.

[@jeremytipton6076]

Can you do a version for large round igloo domes?

[@keithprinn720]

how many moulds required to make economcal use of mixing time? 20? and imagine requiring a thousand? lots of time making before using them

[@bickysakha8813]

How to lay these bloks in T-junction or plus junction ?

[@lucroy]

do you have the plans to cut the wood corectly?

[@gregoriovasquezanyosa3823]

Este ladrillo no lleva fragua me puede explicar mejor como se sujetan la pared gracias

[@trueman2542]

Good designed interloc brick, but you can also speed up your processing work by designing your interloc box as well 😉. Goog effort 👌.

[@stephenmalcome3797]

That's a really good idea

[@clovisilmarbarrosdasilva1369]

Boa tarde, sou do Brasil, cidade Rio Grande, tens com mandar o projeto com medidas, gostei muito dos modelos dos blocos

[@imbaba7270]

thanks, i search many video for this type of mould.but no video in yt for this type of mould😊

[@bobboboff5326]

Это ты там наделал блоков в Пума-Пунку? 😳

[@mikewhitaker2880]

been watching a few "interlocking" brick vids lately, and one question keeps popping up... with all the interlocking parts, there doesn't seem to be enough space for the mortar to fit between and still maintain the interlock.. otherwise nice design....

[@MohsinExperiments]

They are meant to be used without applying cement. They are mainly used for the boundary wall of the house which is not very tall.

[@puntabachata]

Surface bonding cement applied to both faces. And then mortar and rebar in the holes.

[@MercyObizuyo-mt8pd]

Mortter isn't needed. That's why it is interlocking

[@stevenmitchell6347]

Using the same pipe used to create the holes in the blocks, you can lock the blocks together securely without morter... as designed. Adjusting the dimensions SLIGHTLY would permit use of construction adhesive if joint "leaks" are a concern. For retaining walls, perimeter foundation, or simply decorative partition walls, these are quite attractive if different "concrete" suited to each application is used. One could easily incorporate steel reinforcement in the product for additional strength in the active seismic areas like here in Washington state. I like this design best so far. Thank you!

[@drsantoshsinghrathore9308]

​@@stevenmitchell6347 Then it will increase the cost.

[@albertomorel4466]

Hola desde República Dominicana no se bien el morder por favor indicar los centimetros del moder para uno poderlo hacer

[@НиколайНиколаевич-х2я]

where is the place for mortar?

[@williammagrav610]

genial, mas imagina fazer 3k de tijolos para uma obra

[@remziece]

Tranjeri güvenlik tedbiri almadan kullanıyorsunuz. En küçük bir dalgınlığın pahalı sonuçları olur

[@QuranOsunnah3600]

1kg siment makes how many breaks

[@ravigujju1780]

Great idea interlock bricks

[@domsau2]

Congratulations! You didn't show the corner of the wall. I suggest "half brick", in order to place doors and windows easily.

[@NTSRFR4]

Why couldn't you build a house with these?

[@josemamani9014]

Como levantar un muro o habitación con estos bloques de concreto? O que otro material más se necesita

[@chinabrickmachine666]

Our brick making machines can make the interlocking lego bricks, pls contact us if you need.

[@chrisluellen]

These are a great idea but only for local use. These would be a nightmare to ship long distance without them receiving damage to the fragile locking tabs at the current size. Justin this video the was a few with broken corners already. What doesn't get damaged in transport will get damaged by carless workers. I would also recommend putting a channel on the ends that lock together as well. Second problem, which is only with this video, is the mix is way to dry. These will crumble and weather easily.

[@barrywhite7771]

Be soooo careful with those fingers!

[@asmerbas3857]

Very nice

[@Lans888]

Can you ship to me the mold u used?

[@thedarkknight4243]

mortar would still be required

[@СолтанБекбулатов]

А где зазоры на горизонтальные и вертикальные швы??? 😮

[@kolimskiybeech]

При кладке на клей-пену зазоры пол-миллиметра. А вот изготовление- ну бы его нафиг с такими темпами. Слишком муторно, нужны разъëмные пресс-формы.

[@bickysakha8813]

Size of this brick please

[@rcval]

Amazing

[@semeng7511]

Не доработка, сразу видно по углам не будет нормальной стыковки.

[@andrewmacgregor8717]

I've watched a lot of these block making videos and they all leave me asking, do you people not own safety shoes and a work bench!?! The lost time to broken toes and back problems must be crippling!

[@epanfletagens]

Minecraft😮

[@ВикторИванов-и6в2ш]

во-первых , такая сложная форма явно ни к чему . Во-вторых , зазоры между блоками слишком малы даже для клея . Если только не планируешь их просто складывать друг на друга , без ни чего !

[@patriciasabio9121]

Que quilombito pero vale la pena hermoso

[@kevengw]

do you have an stl file for this mold?

[@michaeleck3686]

Ja diese Art zu sägen wird auch die Finger ab Methode genannt. 😂😅😊

[@LetyEpifar]

Dria ayudar con las me didas o si tiene un plano q venda para adquirir las medidas corectas

[@demedidemedeme7963]

TUGLAYI BOYLE YAPSA USTALARA GEREK KALMAYACAK

[@راميعبيد-ن8ي]

ارغب في شراء هذا القالب وغيره تواصل معي لفتح مشروع تجاري

[@nvbac72]

Hay a ơi

[@peteruhl8181]

Cold joints between every block. Good idea if you don't need heating or cooling. Or watertight structure. If you need any of those, this is sh.t. Sorry

[@bolachamauricio9345]

Oba faz a forma or encomenda

[@andreycham4797]

Чем так долбиться с каждым кирпичиком лучше бы уж сделал оснастку типа тисэ

[@Timm69video]

Трудоёмко и бестолково! 5 штук БЕЗ РАСТВОРА и те криво состыковались. На несколько рядов вообще полный швах будет.

[@mkgoatfarm6333]

Mujhe yah kej chaiye

[@citizenoftheworld1658]

hello can you give me the drawings

[@samuelrivon1339]

Bonjour Vous êtes de quelle région

[@YANGDAzeng]

脱模太慢了，没有实际使用价值

[@arlansmith2639]

it is concrete not cement. Cement is one of the ingredients in concrete.

[@BleachedAnubis]

Or just use mortar

[@matthewstewart1826]

stacy

[@NorthAfricantigers]

🙏🙏🙏🙏🙏🙏😍😍😍😍😍😍😍😍😍😘😘😘😘❤❤❤❤❤❤❤❤👍👍👍👍👍👍👍👍👍👍👍🇩🇿🇩🇿🇩🇿

[@mkgoatfarm6333]

Your adress sar

[@Reifenstal]

it a great concept but it uses a lot of material and that is bad for business.

[@nobel100100]

Полная ерунда, раствор добавь и ни чего не сойдутся!

[@deeznuts133]

you mean bricks? (also, cement is an ingredient in concrete...you mean concrete)

[@111jacare]

You have a good idea, but, it can be set up better. Instead of loading from the end, have you thought about a top load? It will mean setting your pipes longer, and refitting the sides of the box. My guess is that you are making a 300 * 150 * 100 block? At this time, you are compressing from the 300 mm end. Would it not be better to compress from the 100 mm? By going vertical, you are not risking bending the pipes, and you are able to get compression over the whole brick. Your current method does not allow you to get full compression on the top edges where the blocks are for the shapes. Am currently in the process of building a sieving table, bolted together, powered by a bicycle drive! My next project after that is to build a vibrating table for the manufacture of interlocking blocks. The third project will be the manufacture of a CSEB machine that, if designed correctly, will be able to make the interlocking blocks or CSEB of different sizes. If I can get around to it, a video will be posted on YT, showing what has been done.

[@jossuec.]

i wish to see that, if you publish the video put the link right here

[@Ubique2927]

How do you stick these things together?

[@khosoobuinjargal1485]

1hours how many block make?

[@speedhunter7303]

Should have a patent for that..

[@mixme8655]

New subscriber always watching your videos very interesting❤❤❤

[@johnmclaren7231]

Lego brick

[@4.094]

Make a hinges lock will unmold easier. But very nice model.

[@renovationdiyhome7458]

faster and more solid to form vertical posts in reinforced concrete, every 3 meters and between the 2 posts pour 7cm of concrete wall in rows. 12 cm if floor or if we have the means. or walls entirely made of rammed earth between sheets when you have little financial means and clayey soil nearby. This is too much work with blocks (the mold will not hold 1000 blocks...) and above all non-compliant because of questionable solidity and gaps in the joints therefore not airtight. but it's very nice to see what some people can do with a few boards

[@luispino7443]

excellent

[@Vovastik170]

Так проще уж опалубку поставить и просто монолит сделать)

[@juderuzzi9018]

I have a better design ... Interlocking yes but my idea is 100% better

[@L3X369]

Someone is stealing all this channel videos and making a ton of views on tiktok...

[@aptknifethrowerguy8342]

Make a proper tapper

[@peteruecker4194]

Wenn in der 2 Lage schon 2-3mm Höhenunterschied ist.Wie ist es dann in der 5 oder 10 Lage 😂

[@neidipires1160]

Parabens pelo seu trabalho gostei muito bom mesmo obrigado, vou fazer uma clpia dessa forma, um abraço.

[@askat25]

раствор намажешь идеально не ляжет кирпичи

[@stevenmitchell6347]

Using the same pipe used to create the holes in the blocks, you can lock the blocks together securely without morter... as designed. Adjusting the dimensions SLIGHTLY would permit use of construction adhesive if joint "leaks" are a concern. For retaining walls, perimeter foundation, or simply decorative partition walls, these are quite attractive if different "concrete" suited to each application is used. One could easily incorporate steel reinforcement in the product for additional strength in the active seismic areas like here in Washington state. I like this design best so far. Thank you!

[@Somali450]

Can you do mud brick like that

[@saladin333]

I can see gaps when put together !

[@jimmycrespo8120]

Podía servir para bloques de concreto celular??

[@juanariza9939]

Eres ingeniero del diseñó

[@ahmadsafrimatjebah4738]

Very good job 😅

[@thelight888]

Machu Picchu.......ahhhhh

[@Andy-jr3mm]

非常有智慧的發明，應該普遍運用在建築上

[@devarajans5246]

Very good!❤️

[@-mejor-que-nostradamus-6152]

Can Not Be Posible That Blocks 1. You Will Need Space For Mortar 2. Not space For Rebar 3. You Must Work In Construction To Know More About Blocks. Amén.

[@mickowens9839]

Very creative bro, well done with your cheap DIY garden bricks. I like the one you made with the little brick pattern better. This one would be great for taller sculptures and back drops

[@jbnrusnya_should_be_punished]

And what kind of solution is planned to fasten the wall from these blocks? If it is the same cement, then the space between the complex shape of the bricks is not enough, because the cement mortar does not compact like that. If with glue, then what kind? The ones in cans are much more expensive than all these forms and blocks combined. And without a binding solution, such a wall is not suitable even for the construction of a garage. It is also not suitable for building a house because, most likely, it does not have enough strength and compression like red or white brick made in factory conditions.

[@АндрейЦаплин-ш8ы]

В сотни раз проще отливать в опалубку стены целиком, чем подобной ерундой заниматься вручную.

[@MrDeicide1]

Unnecessary deep side joints these bricks/wall will not suffer any lateral stress A groove/tenon down the middle is enough