ProFlex CSST: How to Make Connection + Accessories and Equipment

[@snort455]

I would watch a video of all fittings from major brands. You are a born teacher lecturer. You go!

[@charlescunningham8896]

Needed to move my range connection and needed more length. First time using CSST. Existing line was Gastite. Local supplier only has Pro-Flex tube and fittings. They do NOT interchange. Had to re-run the whole line, but it was easy and no leaks!

[@christiantomlin4040]

This is a great video. One thing you need to be careful with when using this style of fitting is the o ring. You can cut it very easily on the sharp stainless edge of the cut piping. Luckily you can buy the o ring and rings separately.

[@beardedgaming1337]

i need to upsize gas line in a house i just got. was thinking of renting a threader and going black but maybe this is a better option...

[@CitizenShane]

Installed 20 feet of trac pipe to repair a galvanized pipe gas leak. I like the fittings of proflex 100x better than trac pipe. Going with proflex next time!

[@godsduality2229]

Trac pipe is what I use. Not sure if proflex has gotten better in the last few years but when proflex and home flex first came out there was nothing but problems with them and leaks. The fittings were terrible. My company wouldn't even work on it. Again maybe it's gotten better, but Trac pipe is what we use and like, especially because the new "snap in" fittings they use its much easier. Trac pipe also now has a csst that can be buried in ground which used to be against code, but now Trac pipe has developed a csst with a much thicker jacket that can be buried.

[@sonofthunder.]

oring hand tighten, plus quarter to half turn w wrench,any more will crush the o ring,I learned hardway...also good to see you wear gloves cutting the pipe leaves razor sharp edge,sliced my finger slipping the orange o ring over,had a helper ...he also did same,a file may help

[@stephenzimny3285]

Great information. Pretty straightforward

[@abibodlogistics]

What are those connetors for the propane tubing called just in case that I want to buy them,I know they will come as a kit.

[@jeffdavis7683]

Just throwing this out there... Proflex uses multiple components inside it's fitting while Gastite uses a large beefy brass fitting without multiple small pieces that can get lost on a jobsite or under a house very easily... Also the "required" special tool Gastite has is not actually required, but it is recommended as a convenience since it will give you an exact cut for stripping away the outer protective layer vs eyeballing it with a utility knife and normally you can get them at no charge from the local rep which needs to certify installers anyway.

[@theplumber585]

Yep!

[@joshcowart2446]

This system seems like how gas tite used to be where you just strip the runner out of the way. That’s much easier than what we use which is flash shield. It requires peeling different layers at different places which always causes leaks. However I’m always wary of using rubber in long term applications. I don’t like having a rubber gasket or O ring that I can’t easily replace.

[@227lazer]

O ring sucks. Get title is best

[@garrysingh9038]

Hi can we use grey quick connect natural gas barbecue pipe to gas cooktop

[@shadoliu6707]

The CSST is three layers ? is the center contains a layer of metal mesh?

[@domgreco7]

Thanks. Great vid.

[@Tactical-Black]

Can you use csst underground and do i need risers with this?

[@davem3789]

Use the poly underground with special fittings to go to steel risers to come out of the ground. All sold at Menards.

[@WisdomInExperience]

Thanks for the great video.

[@tsinay40]

No pipe dope to join brass fitting?

[@ottokiehl5413]

Not for these.

[@giovannidicapo6213]

Is pro flex more expensive?

[@brentbeatty4171]

Connection is not private when you try to access it

[@carlosdelgadillo4098]

How would fix one of these if you cut it by accident???

[@PEXUniverse]

While you can, this is a very risky repair job. There will be plastic covers encasing the gas lines, and these need to come off so you can get to the gas line itself. You will need to disconnect the low-pressure gas line from the gas regulator. Then you will need to take out the high-pressure line before applying epoxy.

[@227lazer]

These fittings leak easy. I find them with damaged pieces leaking all the time. . Gastite is the best. Pinches cast hard making a durable connection.

[@PJBeee]

That is not my experience at all. Pro-flex is VERY leak-resistant. Not a compensated comment here.

[@PJBeee]

Gloves are a great idea here. The CSST steel ends can be SHARP! I speak from experience. Ouch.

[@rnupnorthbrrrsm6123]

Ugh, do you really have to be a professional? I just need about 10-15 feet ran and fittings to hook up my gas range....it will cost me a fortune to get a plumber out here for such a small job ☹️

[@davem3789]

You can get certified on this stuff. But they sell it at Menards. It’s not hard but if you have access to a pipe threader that isn’t hard either and it’s cheaper.

[@rnupnorthbrrrsm6123]

@@davem3789 thank you !

[@markstamp872]

@@rnupnorthbrrrsm6123 Do it yourself. Pro-Flex is super easy to use, but be sure to read the instructions carefully, as this guy skipped some important details.

[@rnupnorthbrrrsm6123]

@@markstamp872 thanks for the encouragement !!! I’m a 53 yr old woman who has to take care of stuff myself so KZbin and viewer comments are a life saver for me, I learn so much !!! Blessings

[@robertcaparelli3535]

worst csst ive ever seen, ward and gastite all the way

[@360S0DJefferson]

Thought I'd let you know this: I liked your video, wanted to buy a complete set of piping, fittings, etc., to run a complete system in my house for LP gas. Called your 800 number and the gal on the other end was pretty much useless and absolutely not helpful. I guess I'll be buying from someone who has better technical support.