Programming a GM TCM with an Autel

This video will guide you thru the process of programming a GM with an Autel. I go over what tools are required. Then I walk you thru the entire process, step by step live as I program the car (only speed up when programming to save time). If you need any of the equipment I mentioned the links are below. Please feel free to comment about what you liked and what future programming or diagnostic videos you would like to see.
Autel Elite:
www.aeswave.co...
Battery Maintainer (70 Amp) its just as good and like $300 less
www.aeswave.co...

[@lords2112]

Just wanted to say...if i had a wish from god to bring someone back..i would skip my family and ask for Ron to come back. he's blessed and always has been....awesome handson skills...) Bless his family also...peace

[@gregjones8501]

Thanks for this video! I just purchased the autel IM608 and ppl keep asking me to do their reprogramming on replacement calve bodies etc. Unfortunately I’ve never used an aftermarket pass thru device and didn’t have a clue as to where to start. This video just shed some major light in a subject I thought I’d never learn! Very to the point and informative! S/N for a min there I thought I was listening to Keith DeFazio!😂

[@blkshk1]

GREAT GIFT FROM GOD THAT YOU LIKE THIS AND CAN DO THIS FOR CAR OWNERS! THANKS!

[@jose1991]

Finally I've been looking for a video like this!

[@ScannerDanner]

I'm digging this charger!

[@mobileadvanceddiagnosticsp551]

The fact the cords are removable is why I like it! Being mobile I am awful hard on cords. I ruined one 70amp one because I broke the cables. It did take 3 years though.

[@1fnjo790]

Wow, That is one cool battery maintainer, and 100 amp output to boot. I bought a no frills IOTA DLS-90 with some custom 12ft cables for less than $300. No digital displays ,It works well but it is pretty much vulnerable to the elements used as it comes and the power cord is just made too short.

[@ranchorelaxo2287]

I use the same IOTA, just wired in a longer, thicker power cord and cut up a pair if 20 foot 4 gauge jumper cables.

[@1fnjo790]

@@ranchorelaxo2287 ,one thing I don't like about my IOTA DLS 90 is the cable clamps always arc attaching it to the battery terminals. It seems to discharge capacitors. I have to hook up the positive one to battery first, then I touch the negative clamp to metal ground away from battery. remove it, wait for a couple seconds and touch it to ground once again and sparks again but much weaker, then I hook the negative cable to the battery clamp and then plug in the AC cord

[@kirkwest6654]

Scanner Danner brought be here!!!

[@basharalqasim1264]

What a brilliant and clear presentation; Thank you very much. Bashar Alqasim Maestro Auto Diagnostics London-UK

[@timtracy9442]

It's almost like this guy knows what he is doing.... Awesome job sir.. :-)

[@ScannerDanner]

Matt, why can't we use the Autel jbox with the Autel tablet? As I'm typing this question, I'm guessing because it is not windows based and is an Android operating system. Is that correct?

[@MaicSalazarDiagnostics]

ScannerDanner that is correct Paul, no manufacture supports android or anything else besides windows so far.

[@ScannerDanner]

Thanks Maic! That's what I thought

[@mobileadvanceddiagnosticsp551]

That is correct. All OEMs require windows operating system (7 or 10 not all have approved 10). For J2534 programming. Now the factory tool stuff can get interesting on what you Program with.

[@johncorcoran5929]

Matt any links to the equipment you use maybe even an amazon shop to help you out some more love the videos keep up the good work would love to see more videos from you.

[@Micko350]

I didn't realise you'd bought an Autel Paul? Or am I just assuming incorrectly? I was also thinking you could go in through the browser but getting the downloads to open might be an issue with Android?

[@MobileAutoElectric]

Tbh I thought is was using the Autel scanner. Didn’t know it was possible with the J-box. So it was a worth watch

[@mph5896]

Thanks! I have a TCM to reprogram for a used trans. Great step by step approach. First time today, I programmed a Ford RSM. It went well without any issues. On to the GM TCM.

[@mph5896]

RS1 I bought a used one off eBay. $450. Plus bought a used laptop that was comparable. $640 with tool, laptop and 1 subscription from gm. If your only doing 1, bring it to the dealer and have them program it

[@mph5896]

@RS1 Tell them you want the TCM refreshed. They will take your money and do it.

[@TheTurbomopar]

What is needed for Ford RSM?

[@tanako98]

Ok This was super helpful! I was lost why the laptop🤔. So the laptop does all the work thru the connector! I would not mind doing GM only! Seems pretty straight forward. Thanks

[@davidbarselow7848]

Hi I had to let you know that this video is very professional thorough and percise I saved it for future use to share and for myself perhaps you can share you thoughts about doing this as a business and hardware accumulation thanks for the video

[@ksg7821]

Thanks. This video has answered my many questions.

[@luiscalleja1471]

Great video good information thanks

[@bigrockk2980]

Great video, thanks for posting this!

[@justin01119]

Very nice. Good to see how other vehicles are programmed, this is Syriac.

[@mobileadvanceddiagnosticsp551]

justin01119 thanks very much sir. I am glad you enjoyed he video.

[@octavio152]

This answered my question if I can use my j tool on gm

[@olko3418]

Good quick video. Thank you for not rambling about useless nonsense.

[@JOATiDetermined]

Thanks for sharing! Very helpful

[@skillz1855]

Extremely detailed.. awesome

[@ronfowler9563]

Great video! Would I need to do this with a no crank, no start, and a p062f code? 2012 Acadia.

[@svca12218]

Awesome video. Thanks. I have to flash a BCM for a 2007 GMC Acadia...I have a powerful laptop, ACDelcoDTS subscription is $55 for 3 days, just need the interface....if not, will have to see if my local shops can come out and do it.....last resort will be to tow the car to dealership.

[@staceydiehl1934]

Well done Matt.

[@abboman8319]

Would a regular smart charger work? What about jumper cables from a running vehicle. Just wondering options. Those things are $600.

[@gabrielq.906]

Does this work with aftermarket tuning files or only oem?

[@amr-50]

Man you are great , thanks for the video

[@1fnjo790]

When it comes to where the program lists the J-box choices does GM actually now list the Autel Maxi Flash (Pro/ Elite)J boxes as options or was field manually typed in by you at an earlier date to display all the J boxes you currently possess ?

[@mobileadvanceddiagnosticsp551]

It only shows j2534 device that the driver is installed. I have a few that I don’t have installed on that partition and it doesn’t show them.

[@michealmiles9606]

How do I know my TCM need a update

[@keithyoung7381]

how did you get your autel jbox to show up in sps?

[@cmautomotive9695]

Nice one I love this video

[@FloridaFrank2010]

Thank you for this - so $1k for the J box, a PC and I can program with a GM subscription =)

[@LoneWolfSnowplowing]

could I use this in instead of a Tech 2 on a 2005 Corvette to program PCM and BCM?

[@mrdman094081]

Great vid. Subscribed and 👍👍.

[@teocarrion2234]

How about if I replaced a 6l80 transmission on a gmc Denali 07 with a used one, how does the programming goes ? Thanks

[@jonathanolivares1261]

hello matt. where are you located? I will like to go to your shop and do my car. I have the same car but I can't get to reprogramed the tcm. ir doesn't let me. it comes as x red mark not the green check mark. It only programmed the ecu. do you know what can be the problem?

[@timtracy9442]

awesome video...

[@sharpcarco]

Great vid , I did and I never sub , I wish you the best !!!

[@seanmiller6701]

Nice work Matt thanks for sharing

[@jonathanarreguin3826]

Can I do this but with a mongoose plus?

[@rhkips]

I'm confused... You installed windows on your Autel? I've already tried using SPS2 from a laptop, and it can't even read the VIN on a 22 Tahoe, and programming fails every time with a communication error. Can I just use Autel's software and not SPS2, since the Autel can read the VIN and view live data?

[@zahidhassan6201]

Thank you

[@jimmacris615]

Great video. Are you relying on ship WiFi or are you using a hotspot of your phone / laptop. ?

[@ericaibtin6342]

Please help me install this software ?

[@qaissabbas1237]

Thank you so much

[@quocle3645]

Hi, how do I install the jbox driver into the laptop? can't seem to find this info anywhere

[@user-lq4ki8kr7x]

NICE THNX

[@MrStevenjr74]

Thanks for this Video. Helped me alot. I need to buy a J-BOX. Does that autel maxiflash that you have work well with most manufacturers. Thats what im leaning towards. Hoping to spend less than $1k on something. Any other recommendations?

[@MrKingflippa]

Where in Florida are you located am in west palm beach I have. A car that I think would need your touch

[@jaykunce793]

Do you need any type of autel scanner, I tried to buy one today and was told I'd have to register and link to a select few scanners, but I keep trying to figure why.

[@Sqwertplays14]

What laptop would be best for this?

[@eugenezelyak2066]

My Autel J2534 won't communicate with GM sps. Connects to the laptop and MaxiPC Suite but doesn't communicate with GM programming software. Please help.

[@emekanwadani2906]

Hi bro I can't access the website

[@tuffygulfbreeze2039]

Hopefully you can help me. I am trying to program vis ACDELCOSPS and in the process it is unable to connect to my J2535 Autel tool. It says device is not there. When I connect my Autel scanner to it via bluetooth, I can communicate with the vehicle. When I disable the bluetooth to disconnect the scanner, and then use the USB cable to connect it to my laptop, I get the signal from Windws stating my Autel device is ready, but in SPS programing, it says it cant communicate with the Autel 2535 device. Thoughts? Is there an additional driver I need to download for the device?

[@isaiahstevenson2779]

Hello, I love the video on programing the ECM/TCM. What are the model number so I can purchase this device.

[@Saab97xlover]

Hey, I have an Autel MaxiSYS Ultra scanner that came with the VCMI controller. Would I be able to use the VCMI instead of the J-Body? Thanks!

[@tbtire7795]

thank you it worked.

[@shimonochayon9671]

Hi thank you for this video Do you know if I can reprogram an used 6t40 tcm ?

[@johnmitchell8925]

I'm confused why would you need a new module after replacing the valve body

[@ezkwipequipmentvideos9309]

Nice video. Have a question on newer vehicles. 2017 Acadia with push button on and start. Is there anything extra needed to keep vehicle on since it has no key and wants to go in sleep mode after a while or is it a non issue during reflash

[@Micko350]

Ezkwip Equipment Videos from my experience when IGN is on(engine off) & the car is connected to a jbox it stays alive while programming.

[@mobileadvanceddiagnosticsp551]

Ezkwip Equipment Videos some of the newer one you need to hold the button till the green light comes on. There is two lights on these styles on the push button. Take holding the button for 30 seconds

[@lorenzoparedes2306]

It would be nice to know what the acronyms are. By using them without clarification, you're automatically excluding some people.

[@JCRUZx91]

Is this flashing the vin to the new tcm? I just did the same thing to a 08 chevy malibu 3.6 changed valve body and tehcm and reprogrammed. But it doesn't not start or crank and prndl doesn't light up as if any gear is in place. I'm not sure what I'm doing wrong. But if I connect my old tcm it start up quick.

[@VitiatedsHOWTO]

Ah the good old days when dorman made it so simple to do this with out all of this🤣🤣

[@bill2677]

Can you disable the cylinder deactivation solenoid ?

[@madmechanic7976]

I'm thinking of getting g the Autel elite over snap on and matco... Is it the best choice?

[@weldingjunkie]

Mad mechanic the Autel isn’t compliant anymore as far as I know.

[@sergiotj3336]

Welding Junkie why?

[@jorgemdiaz7362]

Brother where in florida are you please i need your help

[@davidcano7619]

This is a great video! I just happened to teach this method in Mexico on monday, could i use screen captures of your video to make a manual (in spanish) for my students? of course i would post a link to your channel

[@mobileadvanceddiagnosticsp551]

You are more than welcome to. Thanks for helping improve the industy

[@whatjoshydoestv6741]

Does programing a ECU also apply to TCU’s? I got a error code on my 2000 vw beetle of a missing signal from the TCU. I just bought a used TCU with matching numbers. Does the TCU need to be programmed for any reason?

[@Roberto_Bonilla]

I need programing tcm Chevrolet spark

[@poncho3691]

I have a question the sps don’t detect my Autel maxiesflash elite jbox how can I make it were sps can detect my jbox

[@whysoserious447]

Is this kinda like what a BCM is programmed or this different I need mine done but I Am confused about how it's done

[@tbtire7795]

how do i upload my j2534 autel j box into the menu diagnostic tool on acdelcotds Select diagnostic tool and programming process?

[@mobileadvanceddiagnosticsp551]

Install the driver. It came on a CD or you can login to autel, then download and install it.

[@morganlovell8408]

I swear at 1:27 it sounds like he said "now it's time to hook up the gay box" lol.

[@colassolorzano6353]

Can i use my battery charge card n 2 apms The voltage stay steady. At 12 without move ? Or anything else be said the battery maintained Thank you

[@osvaldovazquez1060]

Whould this be the same steps for a 2010 Chevy equinox? Please answer!!

[@fadi_koka]

Why my flash elite not communicating it’s just like yours please reply I’m trying to program new module in Buick

[@colassolorzano6353]

Fadi Koka thid you fix it. My maxysflash. Dot show like a option. On option show is. J2534 Tool Tech Tech2 dont know what to do.

[@rahrah8076]

Fadi Koka update it

[@scottburgess9861]

I know this is a old video .... sps has made a few changes to their site have you ran into any issues ? My autel will not populate on the tool selection list any ideas.

[@mohammadabdalmutalib8945]

I couldn't register on acdelco tds. it seems like there is a problem in the website. An sugestion please.

[@abubakarisadiqueibrahim481]

Hello does Acdelcotds have the software for all makes and models?

[@Rick-ik4qx]

HELLO MATT, I CAME ACROSS YOUR CHANNEL BY WATCHING PAUL DANNER. I WOULD LIKE TO TRY PROGRAMMING AND BOUGHT THE LAUNCH J-BOX AND I ALSO HAVE THE AUTEL J-BOX THAT CAME WITH MY AUTEL 908P SCAN TOOL.FIRST I WAS WONDERING DOES THE TYPE OF J-BOX BEING USED COME UP AUTOMATICALLY IN THE LIST OF AVAILABLE J-BOXES AVAILABLE ON THE MANUFACTURERS SUBSCRIPTION OR DO I HAVE TO ADD IT. ALSO WOULD I NEED A LSID( LOCKSMITH ID NUMBER) NUMBER WHEN PROGRAMMING SOME ECM'S OR PCM'S BECAUSE OF SECURITY ISSUES. ONE LAST QUESTION- WHAT DO YOU THINK OF THE LAUNCH J-BOX 2534 ? THANK YOU SO MUCH FOR YOUR TIME AND WILLINGNESS TO SHARE INFO WITH US. I HAVE BEEN WATCHING SCANNER DANNER FOR SOME TIME AND I THINK HE IS AWESOME. I AM GLAD HE DIRECTED ME TO YOUR CHANNEL. THANKS AGAIN AND MAY YOU AND YOUR FAMILY BE BLESSED 100 FOLD FOR ALL YOU DO. RICK DAVIES

[@abigaildayuta9538]

I jus want to ask if there's an autel that can program tcm of audi and also have odis programming tool? Kindly respond badly needed it?

[@godsonp3804]

Can this be be programmed without Autel im608pro and the jbox without the laptop?

[@mbarry9737]

Great video, Matt, love the programming info. I wondering why the Autel vs something like a Cardaq? And do you have to partition your laptop for the different makes that you program?

[@mobileadvanceddiagnosticsp551]

Laptop has 5 partitions Drewtech right now is one of the best jbox we. The M is my choice. However, my go to is an older Bosch Mastertech VCI. It’s amazing jbox. I’m hoping Bosch releases a newer version soon

[@Micko350]

Haha I was expecting that Autel Jbox to fail miserably! I have one the regularly fails(albeit yes, it's with the tablet) & have been told on many many occasions to use the Bosch instead!

[@weldingjunkie]

Michael O the Autel is non compliant now

[@Jpilgrim30]

Lol I have the same habit of using proceed with same vin before closing out too

[@elfuertejdmgamer4374]

Excelente

[@jamesl197999]

Great video. What do you think of DrewTechs J2534 CarDAQ-Plus 2 and CarDAQ-M

[@mobileadvanceddiagnosticsp551]

A jbox is almost a jbox. Cardaq offers some things other don't such as the toolbox 3. However, I do no own a cardaq. If you were going to spend money on one get the M. It has the ability to expand as the future changes.www.aeswave.com/CarDAQ-M-Kit-for-Reprogramming-p8978.html

[@boonescomputer]

Exactly the question i needed answered! Thanks for the great info!!

[@AutomotiveCircuitSolutions]

I have the autel scanner with j2534. Does it technically replace a tech2 if i use it the way you used it in the video? I was thinking of getting a tech2 so i can flash gm modules.

[@mobileadvanceddiagnosticsp551]

Automotive Circuit Solutions nothing replaces an original factory tool.

[@paytonmac5665]

TY VM

[@juan201270]

Hey buddy how did you register u autel in the tool list my in not in the list

[@davidmurillo9123]

Why you said we can not use the interface with maxisys scaner? My question is .... if I wanna reprogram any Ecu or Tcm or any other module I have to use any laptop? Or a specific laptop for GM?

[@sergiotj3336]

Yep, i guess, im not sure, i have an maxisys with maxiflash and i can not do it, i use my laptop

[@smallpeakachue]

What state are u located & can i set up an appointment for this exact thing?

[@PhazeRCIL]

Would the Autel work with a DSM car like Mitsubishi?

[@JCRUZx91]

Nice video. Do you what is a better way to do this without having those tools. I work out of my garage. I think I might need new tcm on 08 chevy malibu 3.6

[@mobileadvanceddiagnosticsp551]

joshua cruz got to have a jbox and laptop to do any programming

[@hannarye]

Hello, can you tell me what internet device you are using ? Thanks

[@richardwilhite9174]

for us do it yourselfer,s that cant afford a nice autel system and are getting ready to rebuild the pressure solenoids in my daughters 2007 acadia 6T75 TRANSAXLE Can i take it to my local auto parts store and have the codes cleared and have the tcm relearned and the shift parameters reset

[@mobileadvanceddiagnosticsp551]

No, the auto parts store can not perform this task. Many automotive shops can. Some schedule it with a mobile person like me to do the job.

[@johncatalano85]

Great video, thanks for making it. I’ve been looking at the autel elite, should it come with the new j-box? How would I know the difference between the older one and new

[@mobileadvanceddiagnosticsp551]

john catalano doesn’t seem to be much difference other than size and no antenna. The Elite from AESWave comes with the latest J2534 box and another interface. I got the supper small one with no cord. It’s fun to remember what car I left it in at some back day shops 😂

[@Micko350]

Doesn't matter if you get the model with the aerial because it'll snap off on the first use(when you bump it on the steering wheel getting out of the car)!

[@MrJoeyrodriguez]

Do u have to download software for j2534

[@rohanboswell5408]

Whats the price range. For programming a ecm?

[@sam80412]

What autel are you using with #

[@Blvckmatter]

Which tough book model is this?

[@sanglegend3199]

To register a TDS user, is it free or paid?

[@lopezautotechtips568]

Does this subscription does diagnostic or just programming ?

[@CharlieCars9909]

@Samuel Canales did you get a vxnano u not for a specific make? Or can it do all makes?