Programming Amazon $41 Brushless Kit with Cheap Program Card

Don't forget to check out my video with the programming card instructions & VALUE SHEET for programming your RC ESC
• RC Programmable Card V...

[@billadams8950]

I have this same card, just so you and other people know, there is no 18 setting. When the card displays 12 its actually 11 because the card skips 11 and displays 12 even though its on 11. Count the clicks of the item button when you press them and youll see. So 13 is 12 and 14 is 13 and so on. Fixed my problems

[@willardshimel7099]

Who the hell understands what the items even f ...ing mean

[@UlisesBatalla]

I believe now, that I have taken apart the P-card that there is no item 11. Also, there are 19 parameters and I do not know what they are for this card and motor combo. The issue starts at item 11, Braking frequency. If you could control that parameter you would be able to define the strength of the electronic clamping force during braking.

[@blackfx4x4]

Thanks for the video. Got the same brushless system and card. My Rustler was super slow to get going. This video helped me figure it out a lot.

[@everythingisvibration]

Hey Buddy, do you remember what you changed to stop the slow starts ? I’ve tried everything I can figure out.... Thanks

[@MightyistheRCGamer]

@everythingisvibration you have to change the start mode

[@timfoster6018]

Thanks for the info

[@bra1nc417d]

I bought a Hobby Fans system. Basically, its the same exact thing as any other cheap chinese brand. The program card, which came with it, seemed to work fine, the first time I hooked it up, and I increased the punch/boost setting to max. The system seemed to work ok, except, there was TERRIBLE throttle lag. I mean, we're talking, about 1 second. Now, that may not seem like much, but trust me, it is. Just imagine it; you envision, pulling that trigger, and then counting one ACTUAL second, before there's a throttle response.....YUP. Thing is, that lag is ONLY on take-off. Once my truck was moving, the response was fine, with no lag. Later on, I found out about others having the same issue, and resolving it, with some adjustment in the ESC, using this program card. I got the truck back up on the workbench, proceeded to look for the setting I would need to adjust, hooked the ESC up to the program card, annnnnnd........ I get two rows of left to right, scrolling lights, with ZERO response. I turned the ESC off and on, MANY times, and all, about, 5 seconds apart and still nothing. I tried another battery, same thing, scrolling lights. These chinese knockoffs, are a dime-a-dozen, and they're all the same. The motors are typically fine, but the program card and ESC, are, typically, junk. So many similar reviews out there. Do yourselves a favor and SKIP THE ESC. Only buy the cheap motor, and get a better brand of ESC. Better to pay more now, for a better product, than paying TWICE for an INFERIOR product, down the line.

[@fartdonkey8290]

Just installed this system in a wraith, took half a day, only to have the same scrolling lights you describe on the card. Very pleased with this purchase

[@MightyistheRCGamer]

@MrBrandorambo if it was plugged in backwards it wouldn't even work... Do you even have a programming card because then you would know plugging it in backwards you won't get anything from the card

[@MightyistheRCGamer]

@MrBrandorambo get a life moron

[@audiwankenobi361]

I just purchased this programming card for my Redcat Piranha TR10 that I upgraded to brushless with a after market controller/receiver....very simple to use....i immediately went to item 3 value 10 and now my Piranha does wheelies on demand....the plastic spur gear won't last much longer.

[@MightyistheRCGamer]

Good to hear my friend

[@r.cbikefloyd5390]

@@MightyistheRCGamer which kit is this I wanna run this one a 1/16 scale

[@Aflacist]

@@r.cbikefloyd5390 the fast one

[@garrettwalker1462]

Sub bro because literally out of all the 30 videos I just watched you’re the only one that made any damn sense. I just bought a new cheap upgrade kit off of Banggood for mine WL toys 142019 and when I first plug the ESC in it flashed red But then it stopped doing anything. Any pointers I’m new to this and I just spent a ton of money on a car I can’t even play with lol

[@MightyistheRCGamer]

Don't trip... give a model number or name so I could see what happen we can get to the bottom of this

[@MightyistheRCGamer]

Do you have program card? Just curious

[@DozerBoyRc]

Make sure your throttle setting on transmitter is set to absloute zero. That should get rid of the red light of death.

[@HalloweenFreak31]

Very cool.

[@pistolpete8542]

Thank you man for sharing that with us I need to learn that

[@MightyistheRCGamer]

It's not hard only if you choose to get owned by a RC programming card... But your better then that for sure

[@jamesonattakai661]

Thanks now I know what my problem is

[@dd8067]

11 led mode is missing in fact 12 = 11,, 13=12 etc ...

[@MightyistheRCGamer]

There is no need for 11

[@chrismooneyham5279]

At least we learned its SIMPLE if nothing else.

[@charlieowens2837]

Thank you so much! I wish there were better instructions with it but your video made it make sense.

[@MightyistheRCGamer]

It's super easy don't let things like this get to you they are not as hard as you think

[@derricksmoke3797]

Thanks for the help!

[@leandromvolpato]

can you provide me with the sheet with the configuration via card, I'm not finding it on the internet

[@everythingisvibration]

You still need it ?

[@vlratcliffe1]

Thank you this been fantastic help . Cheers

[@fabricealborghetti4659]

Bonjour pouvez vous m'envoyez la documentation de cette carte svp

[@paulnorton7444]

Thanks for info i had same issue on grass etc👍

[@FIRSTCLASSLEGENDZ]

I changed the khz on mine too 500 khz its the breaking frequency it went up in smoke after spending three hours fixing my new Traxxas 4tec and it burned the car bad

[@polishguywithhardtospellna8227]

Could you explain how is it possible, that esc, that's been sold with 5settings card, can be set in 17 settings with different card? You basically have surpass 60 esc with V1 combo. V2 combo with black, ribbed motor has no card included, but there is V2 card, that has 9(?) settings to adjust. But for example none of those have pwm frequency like the one you're using. So does it mean, your esc can have pwm adjusted to 16kHz, so the motor doesn't buzz in high pitch, when under load? That card possibly first showed up in a set with 80A esc, that was very close software-wise to hw1080, and that combo boomed instantly due to price. It was cheapest crawler brushed combo, you could make quiet. So I'm wondering, shouldn't esc support features, as opposed to just better card offering adjustability to loads of new features? That doesn't make sense 🤔

[@MightyistheRCGamer]

The ESC is not cheap by luck it's complete GARBAGE it burned out after I put new settings SO PLEASE DON'T BUY THIS GARBAGE ESC!!!!

[@FIRSTCLASSLEGENDZ]

Also I changed the low voltage and that didn't go well either it messed my battery up im going to give this another change and stay away from breaking frequency and low voltage and see what happens

[@colinprewett4480]

awesome, i got the esc and realised its crap without the card! Now I know I have the right card thanks to you, do you like the esc, i run it on 3s and it runs nice and cool with 2845 4400kv and 15t pinion on my 124019.

[@r.cbikefloyd5390]

What’s the link to this set up on Amazon

[@PeterBudai]

Hi, what ESC do you have? I have WLtoys 124019 and I believe there is a Racerstar 45A or 60A. Do you have same? If yes, how did you find out, what parameter controlls what function of ESC?

[@muratozcan328]

Merhaba ben bu motordan aldım ama maalesef program aklını ayarlayamıyorum Yani bu videonun Türkçe versiyonu yok mu

[@RCModSquad]

I like that one. You might be able to run the shutoff a little higher you can use a higher “c” rating or add a cap pack. Although I just run mine at 3.2v. Happy New Year!🎆🎈🎊

[@MightyistheRCGamer]

Thanks Bro have a fun safe New Year

[@PERTHWESTOZRC]

David can you please scan and send me a copy of the table of values there that you showed. Mine didn't come with that piece of paper. And the printing on the label is too small to read on the back of the programming card.

[@PERTHWESTOZRC]

FYI this card did not work with my surpass hobby 60A esc in my 144001 or 019, all that happens when I plug it in is 2 rows of red LEDs just scroll along the 1-10 and pressing any of the command buttons does not a thing

[@PERTHWESTOZRC]

Just tried it on my LC racing EMB-1H with 35A hobby wing ESC and does not work as well. Scrolls LEDs also, any ideas why its doing this guys?

[@pieterkruijver3939]

that esc that you using is a goolrc esc

[@MightyistheRCGamer]

Yes in the video you are watching

[@giorzatore]

Great video, do you remember what are the parameters to change to make it go fast?

[@MightyistheRCGamer]

No I don't remember off hand

[@papaobie826]

i have same with This Card, but not good function, if I connect to ESC, the light still running on from 1~ 10 for item and value and continuously like that.. I have press all button but still not respons. I try to ESC Surpass Hobby, ZD Racing , Gool RC .. i don't Know what the Problem

[@MightyistheRCGamer]

I only got 2 or 1 run out of mine and it started acting strange and then not working at all but I return it and bought a Surpass Hobby 60amp ESC and 4370 brushless motor for $60 and it didn't even need programming and works Perfectly Fine that goolrc stuff is GARBAGE so now if I am going to go cheap then I am only going to use Surpass Hobby its only $60 REMEMBER THE $40 GOOLRC COMBOS ARE GARBAGE!!!

[@renearteaga4110]

I have the same problem

[@conwaywebb8686]

I have the same setup in the ESC does not like 3s much it will go up in smoke

[@MightyistheRCGamer]

The ESC is Not Cheap meaning Low Priced by Luck it's complete GARBAGE. The motor is ok but when you get the motor to hot the magnets fall off and the motor won't work no more.... I bought a better combo for $60 and never had problems again and I have more speed and more power

[@martez752]

@@MightyistheRCGamer what combo you have now?

[@MightyistheRCGamer]

@@martez752 amzn.to/3trKWiQ

[@martez752]

@@MightyistheRCGamer what type of speeds your getting and do you need a program card to get it going? I have a hobby wing card will that work?

[@MightyistheRCGamer]

@@martez752 yes YOU ALWAYS NEED A PROGRAM CARD don't let anyone tell you different. The Hobbywing will work on it but speed depends on your setup but I am getting great speed on 3s but I think the combo I sent you. You can use 4s

[@jlimlingan]

need the manual how can I get?

[@MightyistheRCGamer]

The card doesn't come with a manual because the instructions are when you buy a ESC. The ESC will come with instructions on how to program it.

[@davidmesecherjr.7259]

When the chip plugs in it blinks top and bottom left to right and dosnt do anything

[@MightyistheRCGamer]

I don't understand

[@davidmesecherjr.7259]

@MightyistheRCGamer it starts on 1 and will blink all the way across the bord on both set of lights.

[@oskartubekp]

Hello friend, thanks for the video. I have a question. What about the number 11? It doesn't change, I understand, right? Because the card goes from 10 to 12. Thank you so much.

[@MightyistheRCGamer]

What is number 11 anyways and what ESC are you using

[@oskartubekp]

@@MightyistheRCGamer My esc is that of the wltoys 124016 v2. I bought the card to raise the battery cutoff. But my question is? the leds that mark 12 are equivalent to the number 11 and 13 = 12 and so?

[@MightyistheRCGamer]

@@oskartubekp it's because the ESC doesn't support the number 12 or your card isn't completely compatible with your ESC

[@oskartubekp]

@@MightyistheRCGamer But I see that this problem happens to more people! So what card do I buy for wltoys? I just wanted to know why it doesn't give the option of 11

[@MightyistheRCGamer]

@@oskartubekp buy a real hobbywing program card

[@edwardlove4300]

Hello RC gamer, I got a budget V2.V3 no name ESC from AliExpress and my program card just runs flashing left to right. Nothing I can do to stop this happening. I just want to install the ESC into a trail truck with 2S. My question is if the card is junk can you recommend just trying to return the package or trying to program it using the beep beep way? Thanks in advance. Edward

[@MightyistheRCGamer]

Now you can have a few problems the ESC could not be programmable or your Programming Card is not compatible with it or the program card is no good... if your ESC came with a switch to program it then you will have to learn and go online or on KZbin to find out how to do it

[@edwardlove4300]

Thanks for your prompt response. Best wishes, Edward

[@Speedslays]

My lights just keep flashing ! Can't program anything

[@renearteaga4110]

I have the same problem Anybody know how to fix

[@daveszangulies9938]

Unplug receiver power off and on again

[@theuntouchables808]

@@renearteaga4110 ones you have set a value . press OK .

[@MightyistheRCGamer]

Yes you are correct

[@jc49fishniner4lif7]

What happened to number 11 do u know 🤔🤔

[@MightyistheRCGamer]

I never mess with 11 anyways but this is happening because the ESC was made without 11 it's not the program card because 11 is there when I connect to a Name Brand ESC. It's these cheap China ESCs they suck my burned out just because I programmed it and the cheap ESC didn't like it so it just burned out

[@jc49fishniner4lif7]

@@MightyistheRCGamer cool 👍

[@digeolrc8586]

What esc is that?

[@Aflacist]

Thanks man, this really helped me out. I just need to figure out the cords now lol.

[@MightyistheRCGamer]

If your rc is going backwards when trying to go forward then you can change the motor rotation with the program card or you can keep the middle wire connected always and change the other 2 wires

[@Aflacist]

@@MightyistheRCGamer thank you! Your video literally saved me, I was able to actually just reverse the rotation based off of your video!!

[@MightyistheRCGamer]

@@Aflacist You just made my day bro I love to help people

[@MightyistheRCGamer]

@@Aflacist if you need more help watch this video my channel is the only one that has it kzbin.info/www/bejne/rmq1oJqVfdF3fa8

[@SubZ3ro907]

I have this combo but got it from wish. I lost the damn paper so now I can't program the esc. I was trying to take screenshots of yours as u were doing the video but can't see all the values. Could you please email me a photo of that paperwork or post a still photo of it? That would be a huge help. Thanks bro.

[@MightyistheRCGamer]

Tell me what you need and I will make a video of what you need

[@MightyistheRCGamer]

I just made a video for you of the VALUES Sheet

[@MightyistheRCGamer]

kzbin.info/www/bejne/rmq1oJqVfdF3fa8

[@seanwilson9117]

Is thee somewhere the chart is available online? I've misplaced mine

[@MightyistheRCGamer]

NO

[@MightyistheRCGamer]

But I made this video to help you and IT'S THE CHART PLEASE SHARE THE VIDEO TO HELP OTHERS kzbin.info/www/bejne/rmq1oJqVfdF3fa8

[@rellzrc5879]

How I got one and all the lights do is run across

[@MightyistheRCGamer]

Broken

[@MightyistheRCGamer]

These program cards SUCK

[@jonathanmackey3282]

Did it beep beep beep beep before you hooked up the program card

[@MightyistheRCGamer]

Yes... but it's a CRAPPIE combo it burned out on 2s

[@jonathanmackey3282]

WOW okay

[@jonathanmackey3282]

You want to sell that program card?

[@MightyistheRCGamer]

@@jonathanmackey3282 I bought it on Amazon for only $10

[@daveszangulies9938]

Where’s number 11

[@serroxat]

I bought same motor but I can’t programming I did same thing what operating say

[@MightyistheRCGamer]

Throw it in the trash

[@serroxat]

@@MightyistheRCGamer why

[@serroxat]

Motor is working

[@MightyistheRCGamer]

@@serroxat it dies fast the ESC won't last it's trash

[@serroxat]

@@MightyistheRCGamer esc fan is work and beeping so I can’t use it and if I buy new esc can work with same motor

[@theuntouchables808]

With someone would translated this Sheet properly

[@MightyistheRCGamer]

The sheet doesn't need to be explained because it is literally on the back of the program card.... But I did make a video showing the program sheet bro

[@MightyistheRCGamer]

I left a link to the video with the program sheet in the description of this video

[@KartalKafadar]

Hello. I have the same esc and control card, but when I connect the control card to esc, the ITEM and VALUE lights automatically start from the first row and continue to light up as 1 2 3 4 5 6 7 8 9 10. Where am I making a mistake, can you help me?

[@MightyistheRCGamer]

The ESC is VERY FAULTY so don't expect it to work well. After programming mine it started acting stupid and then it and then caught fire on 2s only.... I can't help you because it's already acting faulty just like mine did before a blew... but you can't press reset to try to see if it fixes the problem

[@KartalKafadar]

@@MightyistheRCGamer My esc was working well, I connected the program card, but as I said, the lights of the program card follow sequentially and the lights on your program card remain constant. I can't power up with esc right now. How can I reset this?

[@MightyistheRCGamer]

@@KartalKafadar I think you connect the program card to the ESC turn on the ESC and then press the reset button on the Programming Card

[@MightyistheRCGamer]

@@KartalKafadar the problem could be the ESC or it could be the actual Programming Card both of them are very unreliable

[@KartalKafadar]

@@MightyistheRCGamer Can you write me your e-mail address and I will send you a video of your error.

[@hithereperson8137]

mine when turning goes forward how do I fix that?

[@MightyistheRCGamer]

I think that might be a wire that is not connected to the correct... or the wrong channel in the receiver of you Transmitter needs to be trimmed

[@MightyistheRCGamer]

When plugging in this motor the wire that is in the middle has to always be connected to the middle wire of the ESC but the other two can be mixed-and-matched... when doing upgrade on my Traxxas/ when I turned it on it would go forward and it was in the wrong channel on the receiver

[@hithereperson8137]

@@MightyistheRCGamer Yup that was the problem, you just earned a sub :)

[@MightyistheRCGamer]

@@hithereperson8137 Welcome to the Family

[@hithereperson8137]

@@MightyistheRCGamer glad to be here!

[@AFIKAV]

WT ESC U HAVE ?

[@MightyistheRCGamer]

The ESC in the video is complete GARBAGE

[@AFIKAV]

@@MightyistheRCGamer i look for universal program card..not hobywing

[@MightyistheRCGamer]

@@AFIKAV the program card in the video is that exact one you need

[@AFIKAV]

@@MightyistheRCGamer but is only 2options?

[@AFIKAV]

Wt the options?

[@andreklaus1038]

But it goes from 10 to 12? Is dont think so. Point and point means 11 or am i wrong?

[@MightyistheRCGamer]

All the lights go up to ten but when going to 11 after going to 10:00 only one light will be on meaning you are on number 11

[@andreklaus1038]

@@MightyistheRCGamer ok than i see that wrong. Mine came today. Then i can test it tomorrow. Ty for the answer. I am german btw... sry for my english. 😄

[@MightyistheRCGamer]

Yes it's kinda hard to understand what your talking about but i promise to help if you have patience

[@MightyistheRCGamer]

There is no 11... Only 12

[@MightyistheRCGamer]

There is no 11

[@traxxas-stampede12-77]

just beware those cheapo brushless esc's will NOT survive long on a 3s 80c lipo

[@MightyistheRCGamer]

Your right bro didn't last me 2 runs ESC was dying after 1 uses.. But I bought a better ESC and motor in another video