Project Refresh 996 Introduction!

  Рет қаралды 1,045

Kevin’s European Garage

Kevin’s European Garage

Күн бұрын

Пікірлер: 38
@davidB997
@davidB997 3 жыл бұрын
Sorry for the problem, but it’s going to make some very helpful content for the rest of us. Just finished refreshing my suspension, new shocks, arms etc by following your videos, they proved invaluable so thank you for all of your efforts.
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
Thanks for the support. I’ll have plenty for you to watch. I have a feeling as I go on I’ll be adding more. That’s how it always is.
@nsltrc
@nsltrc 3 жыл бұрын
I recently replaced all three tensioners. Couple were significantly shorter than the new part. It seems to have addressed some of the rattle. It made sense to replace a critical engine part that is now 20 years old. Some essential tips based on forums and my own experience: - Obtain the correct cam locking tool based on your engine. Short plate for 5 chain, long one for 3 chain. 5 chain engine only has slot on the bottom cam. - Know the correct orientation of the cam slots at TDC. 360 degree engine rotation needed between Bank 1 and Bank 2 when moving over to other side. - Buy fresh cam cover seals. The green plugs. And new aluminum washers for the tensioners. - Definitely do the research on the correct tensioner part numbers based on your engine type. Roller chain versus toothed. Numbers changed over the years. - Parts -55 or -56 (one with external spring) are designed only for the non-roller (hyvo) type chains
- A shallow & thin 32mm socket will make life easier. For Bank 1 and IMS you can stack a socket inside a deep socket for screwing back in. Newer Bank 2 tensioners have a 8mm hex. This is for good reason because there is limited space to get a socket to fit on the old Bank 2 tensioner, even with the AC pulled out. I ended up machining a socket down to thin walls. - Definitely drain the engine oil! It will make the task more tolerable and you will not be battling with multiple liters of oil draining out and putting it back in later. - For the bottom Bank 1 tensioner make sure you have enough leverage and space to press in the tensioner while at the same time screwing it in. There is no grenade pin so you have to press the tension in yourself. Get the car high up enough to also turn the torque wrench on the IMS tensioner. - A boroscope will make locating the rear AC bolt easier. You can’t take too many blind goes before this head strips. Ensure the socket is lined up straight on the bolt head. Try a 1/4” extension & ratchet for better feel. The bolt is captive. - The engine temp sensor can be a bear to put back in. Make sure you don’t drop the rubber gasket under the intake when putting it back. - It may be a good idea to take cam deviation readings (on a hot engine) before and after this procedure. - Generally a good idea to mark the accessory belt orientation so it goes back in the same direction. Take the time to spin the pulleys to check for noises/issues.
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
I have a 5 chain engine. I’ll get the kit to hold it all together. As far as I know no one has changed the chain type. But I’ll look into it when I get closer to doing it.
@nsltrc
@nsltrc 3 жыл бұрын
@@KevinsEuropeanGarage I also have a five chain. Let me know if you need any more details on this job.
@Rockafella1861
@Rockafella1861 3 жыл бұрын
You have really great content man. Bummer about the coolant but glad to see so many positives come out of it too with all the updates needed.
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
Thanks I appreciate the support! I was planning on doing most of this stuff as a winter project. But if I'm going to pull her apart I might as well get it all done.
@mikebell1961
@mikebell1961 3 жыл бұрын
Good Luck Kevin, just spent the last two FULL WEEKENDS replacing the Entire front and rear suspension. Rotors and Pads as well. on my 996 coupe. So Like you, in for a penny in for a pound. Might as well knock it all out while your under there and up to your elbows in dirt and old oil:)
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
Thanks. I agree, might as well just dive in deep and get what ever needs changing done. I'm just doing it about 6 months early as this was the plan for the winter.
@mikebell1961
@mikebell1961 3 жыл бұрын
@@KevinsEuropeanGarage I think my next deep dive will be an exhaust upgrade. I bought this car from the original owner retired navy fighter pilot from San Diego. Anyway he had every receipt from the day he bought the car in Carlsbad. But no receipts for the suspension. When I removed it, it was all original. So I am replacing parts as I come across them. Exhaust is original so sure replacing would be helpful.
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
At least you have a SoCal car with no rust. Mine was garaged it’s whole life it has no rust either. Should make for removing the exhaust pretty easy.
@mikebell1961
@mikebell1961 3 жыл бұрын
@@KevinsEuropeanGarage I hope so. Sometimes I forget how having a New England Car makes such a difference. When I lived on Fort Devens my first car was a 66 Mustang and it was held together with Bondo and Fiberglass due to all the rust. Most of my friends had two cars, A Winter beater with snow tires and a nice car that stayed in the garage all winter
@HellaRandomVideos
@HellaRandomVideos 3 жыл бұрын
Excited to follow!
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
Thanks new stuff will be coming soon
@andriikifiak4936
@andriikifiak4936 3 жыл бұрын
Sorry to see that coolant leak... But from another side - looking forward to a super content! Good luck with this project Kevin!
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
Thanks I was pretty sure it was original. there’s will be a lot of content coming soon.
@seanbill942
@seanbill942 3 жыл бұрын
Great videos Kevin, love the channel!
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
Thanks for the support!
@jeffreyalexander4325
@jeffreyalexander4325 3 жыл бұрын
Kevin, I echo everyone's sentiments as well :(. I had mine go out last year. Was a PITA to get it out (996.2). As everyone knows, you have to lower the engine a bit to get some clearance. One other thing that I had to change as a result was the engine mounts (they went kaput or were already bad?). My suggestion since you have a laundry list of things that you are doing is to change the coolant hoses as well. I changed some of mine out 2 years ago when I did my spark plugs/coil packs ( I actually broke one of my hoses in the process of doing the plugs which is why I changed the coolant hoses). Another caveat - if you are going to replace the return hoses (in particular the one with the flange), the only one that FCP Euro sells is the quick connect hose, which means you have to change the flange as well! Other than that, have fun and keep making great content!
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
Thanks for the tip. I’ll take a look over it all when I get in there I’ll probably changing more as I get deeper into the refresh.
@nsltrc
@nsltrc 3 жыл бұрын
rennlist.com/forums/996-forum/737700-simple-3-step-complete-coolant-drain-updated-w-refill-procedure-water-pump-tips.html Procedure from Ahsai on rennlist gets all the coolant out so you are not mixing.
@512TXSDIY
@512TXSDIY 3 жыл бұрын
Sorry to hear about your troubles. Sounds like you’re going to have a lot more videos coming up though :-). I too have a box of parts I never got around to installing on the Cayman. I’ll get to it eventually or when of course things break.
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
I hear you on the box of parts. This is gonna take a me a while to get it all done. I still have to get a lot of the stuff.
@512TXSDIY
@512TXSDIY 3 жыл бұрын
@@KevinsEuropeanGarage Very true. I get so OCD and want to finish everything. I’ve learned that that’s just not the case and need to take it slow. Really looking forward to some additional videos here in the near future.
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
I know I have to balance driving the car and wanting to work on it. It’s just too much fun to drive to want to take it off the road to work on it but now I think it’s time to do it
@512TXSDIY
@512TXSDIY 3 жыл бұрын
@@KevinsEuropeanGarage very true!
@mbjohnston
@mbjohnston 3 жыл бұрын
Thanks for the great content on the 996! I recently used Fister to upgrade my muffler and had a terrific experience. The sound is amazing! Looking forward to following the repairs! Good luck!
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
Thanks. I can’t wait to have some real exhaust sound come out of that engine. Stock it far too quiet!
@boffam00
@boffam00 3 жыл бұрын
Be sure to get the OEM expansion tank ($$$). The previous owner did the Gundo hack and so I have no point of comparison, but my car sounds amazing (he also did the same intake mod that you have). Also consider the “Ultimate” AOS that I have heard a lot of good things about. I don’t wish breakdowns on your car but it means some great content for the rest of us who will eventually be in the same boat. Keep up the great work!!!
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
I have been contemplating using an aftermarket tank. I’m still thinking about it. I’ll look into the ultimate AOS I think I remember reading about it at one point. Definitely will be a lot of content coming soon.
@nsltrc
@nsltrc 3 жыл бұрын
@@KevinsEuropeanGarage The ultimate AOS seems like a solid solution, however price is a big hurdle. Depends how you look at it over time.
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
I don’t drive the car much maybe 2k to 3k a year. So I might just go with factory
@nsltrc
@nsltrc 3 жыл бұрын
There is a discussion right now on Rennlist about fitting a Mk 2 tank in a Mk1. Would be worthwhile following as there’s a big cost difference on the OEM part.
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
I’ll have to check it out unfortunately though I have ordered my tank already
@nsltrc
@nsltrc 3 жыл бұрын
Mk2 injectors for $40 each (pelican) would be my approach vs cleaning. Just cut in new locking grooves in the plastic
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
I still might get them cleaned even if I replace them. I have friend at his shop can do cleaning and testing.
@nolanohana
@nolanohana 3 жыл бұрын
Coolant tank is a known failure point Kevin, had mine replaced proactively. At least it didn’t cause any damage. Change the water pump as well, another timed-out part. How are the motor mounts? Does the exhaust sag or is their a clunking sound from the rear?
@KevinsEuropeanGarage
@KevinsEuropeanGarage 3 жыл бұрын
I was planning on doing the tank and a lot of this stuff like the tensioners as a winter project. I got lucky that it let go just as I got home. I've already done mounts and the water pump was changed not too long ago but that might get done too just because.
Bumpers, Mufflers, Spark Plugs! Project Refresh 996 Part 2
15:23
Kevin’s European Garage
Рет қаралды 1,2 М.
How to install a Coolant Expansion Tank and Injectors. Refresh 996 part 4.
43:48
Kevin’s European Garage
Рет қаралды 6 М.
World’s strongest WOMAN vs regular GIRLS
00:56
A4
Рет қаралды 15 МЛН
黑的奸计得逞 #古风
00:24
Black and white double fury
Рет қаралды 30 МЛН
Smart Sigma Kid #funny #sigma
00:14
CRAZY GREAPA
Рет қаралды 97 МЛН
UFC 308 : Уиттакер VS Чимаев
01:54
Setanta Sports UFC
Рет қаралды 914 М.
How to Drive a Super Car! Ferrari 488 GTB Xtreme Xperience Review
16:25
Kevin’s European Garage
Рет қаралды 799
Porsche 996 Spark Plug Tube DIY Refresh 996 Part 3
14:00
Kevin’s European Garage
Рет қаралды 5 М.
Will This Popular Engine Oil Additive Save My Engine?
8:40
Kevin’s European Garage
Рет қаралды 16 М.
Are Golf R Engine Internals Better than a GTI?
16:50
Deutsche Auto Parts
Рет қаралды 480 М.
How to Fister Style mod a Porsche 996’s exhaust
12:02
Kevin’s European Garage
Рет қаралды 9 М.
Continental Tires Extreme Contact New DWS06 Plus Tire Review!
8:31
Kevin’s European Garage
Рет қаралды 48 М.
I BOUGHT A WRECKED PORSCHE 911 GT3 & REBUILT IT IN 24 HOURS
41:17
Mat Armstrong
Рет қаралды 14 МЛН
BMW E46 или Renault Kapture однажды в Сочи
0:58
ОДНАЖДЫ В СОЧИ
Рет қаралды 3 МЛН