the ram information was added after your printout. but fixed the arrow covering that pinout, did not even notice that. 😂 the picture on top is correct and shows the pin outs super clear. thanks again
@hlieb46017 жыл бұрын
Hey JC just did that and blew up my 5v regulator (not your fault I connected my f7 before watching your video ) but it is good to see that I didn't make a mistake in doing what I did. I have connected my f7 exactly like you did with yours and wanted to test the board before the next step putting in the ESC's plugged in the battery and... fry baby fry
@adrian60able7 жыл бұрын
Thanks JC for the omnibus F7 setup. Now I have to try out myself . Very greatful for your video put it out .
@tommysmith29087 жыл бұрын
Great Video JC. I love the Omnibus, but every card is like playing whack-a-mole with the pin outs. Thanks for the info...
@TheMadmacs7 жыл бұрын
ps. does anybody else just click 'like' at the start of PBF's videos now,? its that reliably useful info.
@maximusimany42756 жыл бұрын
Bought F4 aV2 not that much bugs motors stayed on reverse mood(bug) but couple cli cod’s well done and helpful as usual thank you
@nitronaf7 жыл бұрын
I want to buy one for my next 6s rig. Where would I wire the capacitor that they recommend
@jeffvenable38457 жыл бұрын
Awesome video man. thanks for taking the time man...i dont know when i will try it but i know who i will talk to if i have an issue. :)
@schmudge6 жыл бұрын
Thanks JC for all you did, Priceless
@briancase99097 жыл бұрын
Your flight controller how-to videos are excellent. A lot of what you learn on these is very applicable to doing forensics on other FCs as well. Thanks! Quick question... I see you do not have the VTX and Camera on the same ground pad. I thought the rule for best OSD/Camera signal was to always tie those two into the same ground pad. Are these ground pads close enough in proximity (no resistance between them) to not worry about it???
@lokisdream84387 жыл бұрын
was looking at different hook up options for a 5" Kraken Worx here and due to the very narrow arms I was considering swapping out the Skitzo RF1 and EMAX 30a bullets with an AIO. So in short I was checking in at my local hobby store and they just got in a Cicada F4 AIO. Now I wouldn't have taken the Cicada but they brought to my attention that it is an F4 Omnibus running CicadaESC's and I remembered your great review of Omnibus FC's so I bought it. I am not having any luck getting much intel on it and I am curious as to what you know and could throw my way. Much appreciated. Cheers...
@stevenseaman83947 жыл бұрын
Hey Jc what size wire do you use for vbat and ground? On the F4 I saw you said use 14 gauge. I was planning on using 26 gauge for fc pdb and using 14 gauge pig tail with xt60, 16/18 gauge for esc. Also I'm using 2407 motors, 184 amp matec pdb ,flip 32 f7 omnibus and wraith 32 esc 35 amp esc.i just got a little tripped up with the the 14 gauge you used with f4. Thanks for all your help.
@hughhemington95597 жыл бұрын
Diagrams like the printed one seen here would all be better if the labels were next to the pins horizontally, and not interleaved! Even if your cam OR vtx can "use" full vbatt power, doesn't it just step it down within the device? And if so, does it consume power and produce heat in doing so? (and is it really beneficial to be stepping the power down in multiple locations?) Or do some cams and tx's use full vbatt power straight through with no step-down?
@TheMadmacs7 жыл бұрын
i was gonna ask this too, in terms of ultra cheap vtx the eachine tx526 and the runcam swift mini, am i better to feed them 5v to avoid heat issues ?
@chrismichaels52167 жыл бұрын
Do you think additional power filtering is needed for this FC for the vtx and camera? What have you used?
@mcqueezi33886 жыл бұрын
PBF, we will always remember you... Rest in peace
@beysim17 жыл бұрын
Great video Blue Falcon!.. I have one question: i followed your tutorials on how to set up quad with omnibus f3 series and i have difficulty to set up RSSI value on my osd and betaflight configurator. i use rlink 433mhz uhf system as tx/rx and rx is only outputting analog RSSI. Is there any way we can use this analog RSSI IN OMNIBUS F3? RSSI pin seems to do nothing. if omnibus is not capable to do this (shame on them because we have this pin on the board) is F7 controller able to use analog RSSI?? Sorry for long question. i thrust on your experience.
@Bobby117 жыл бұрын
This is why i check, and re check with a multi meter, at least the pins are actually labelled correctly :)
@ProjectBlueFalcon7 жыл бұрын
Yep always good to check. If I hadn't checked I would have wired the receiver ground to the power pin.
@drumrboynoid7 жыл бұрын
My question is what if you wanted to power the board via an external 5V PDB instead of the direct battery voltage. How would the internal OSD know what the battery voltage is? Thanks in advance.
@robertkampf49937 жыл бұрын
would you recommend to connect a omnibus f7 to a matek fchub-6s with a 8 pin jst sh cable or with individual wires? the jst sh option would be cleaner easier to disconnect but thicker individual wires should be more robust and secure.
@NeauxGeaux7 жыл бұрын
JC Like your vid's- Very informative - but I hate to but ask this but on the Flip 32 F7 where you can see J7-4 PWM1-4 and GND where would the +5 volt to esc connect to? Or do I have the wrong esc?
@HighVoltageProjects7 жыл бұрын
great video thanks .that schematic is very poor and I think it's going to confuse a lot of ppl .looking fwd to seeing what you think of the FC once it's actually flying. I wanted to use the F4 but with no way of changing the the telemetry inversion with software it just causes more issues to potentially go wrong . I have a question .....In your opinion what's the best FC that has an on-board BF OSD that has software inversion? thanks for the great vids John
@BarefootBeekeeper5 жыл бұрын
So what is that TX pin for?
@lucid59947 жыл бұрын
Hey PBF, what do you think the next big thing in hardware will be for FPV?
@jaybird69097 жыл бұрын
hey jc. highly appreciate the videos. super informative. I was just curious if you know how many hardware inverters the f7 has. does it have more than 1 like the f4 boards?
@mikeydeefpv86617 жыл бұрын
hey there, great video! i have the same question as neil. i have 3 of these boards at home - and wanted to hook them up in my 6s rigs... but where do i put the capacitor they advise usto use? i put it on the lipo pads of my 4in1 esc... my quad flies mor or less normal on 4s but on 6s it flips out of control directly after takeoff (flashed the latest bf 3.2 3 days ago) i hope i did not fry my board by wiring the cap wrong 😳
@YAdr897 жыл бұрын
Hi, is there the risk of to fry the cam or vtx if I plug on 5v or vcc? If yes, why? The spikes of esc and motors?
@yksikaksikolmen7 жыл бұрын
How is it going with your flight controller JC ? I buy one unseen :)
@juancarlosoanelli96263 жыл бұрын
friend, any help to connect the uv100 sonar on the nxt f7 ,? You need resistotes as I read there, I use inav
@JohannSpringsits6 жыл бұрын
Hi Very informative Channel ,but here is my Question I bought a Readytovsky F7 Flightcontroller but i cannot find any manual about it or explanation how to connect the ESC`s or the Sbus or any other things what to build on please help if you can
@ashimkiranpramanik99887 жыл бұрын
i want to use omnibus f7, so what will be the requirement of all other components or module? like Tx Rx model no, Battery, motor,power distribution board,camera,propeller length rating etc.
@einsteind7 жыл бұрын
very useful and informative,,,,, thanks
@bryanwolfe21437 жыл бұрын
For Spektrum, if the 3v actually the 3.3v? They no longer provide the plug :/
@colelandreneau3047 жыл бұрын
is this the one with 2 gyros. one like the revolt and a regular?
@xfire1197 жыл бұрын
Hi, Is it possible to add GPS to F7 with the same F4?
@juancarlosoanelli96264 жыл бұрын
12 volt directos?
@toddbeal43737 жыл бұрын
where do u get this F7??
@danimoddj7 жыл бұрын
garbage....I test it and it has a lot of bugs in betaflight 3.2 , no buzzer, no sbus,,, no vbat menus in configurator... etc.. Finally I change for a kiss, much better, and much better fly
@ProjectBlueFalcon7 жыл бұрын
DanimoD Fpv realize the firmware it's still in the beta testing. Using beta kiss firmware it's just as buggy. Just be patient and the firmware will be finalized and released soon