Repairing a 16” Crease in Aluminum with Paintless Dent Repair - Can It Be Done?

[@cmils1785]

Great work man, walked it right out!!!!👍🏼👍🏼

[@ProPDRofGa]

C Miller appreciate it man 👊🏻💥

[@ProPDRofGa]

frogmanvc hey Izzy 👋

[@ProPDRofGa]

frogmanvc what forum are you referring to?

[@bigbigsurge]

I need y’all to work magic on my F-150!

[@greenbullitt6999]

That's a super repair … Congrats

[@ProPDRofGa]

Green Bullitt thank you! I appreciate it 😊

[@ProPDRofGa]

Green Bullitt thank you! I appreciate it 😊

[@straightlines7432]

How wide was the tip on the whale tail? Is that all you used on that repair ? Looks great

[@ProPDRofGa]

straight lines If I remember right I alternated between a standard head and a wide head whale tail, I tortched the end to slide through the glue easier as well, I only remember using whale tails as the crease was right in the middle of a brace inside the door. I appreciate the compliment.

[@thefixer4414]

Good job bro

[@ProPDRofGa]

The Fixer thanks buddy!

[@timothyday9597]

Where are you located ? I need a dent pulled from my ‘19 f150

[@ProPDRofGa]

We’re based out of Griffin but are mobile and cover a wide area, where are you located?

[@MrAWorthy1]

Can you tell me what tool is was that you used? You m actually going to attempt this later this week

[@ProPDRofGa]

All of our tools are purchased through PDR tool distributors. I can’t remember what tool was used, most likely a whale tail or J hook of some kind.

[@randomguy2369]

Dang only if you guys were in Colorado I parked my car and when I came back some pos left a crease on the back door

[@ProPDRofGa]

With as much hail as you guys get you should have tons of PDR companies around qualified to take car of that for you 👍

[@jeffreyhinman1397]

What’s the prices for pdr? Obviously it varies, but on average for smaller dings or creases...

[@ProPDRofGa]

Typically a 1 inch dent starts at $150 and increases by $50 per additional inches of damage, if the panel is made of aluminum or if the damage crosses a body line that would change things a bit, typically by about 25%.

[@williamwhitley7969]

Could you recommend any company in Colorado for the same repair?

[@ProPDRofGa]

What part of Colorado?

[@williamwhitley7969]

@@ProPDRofGa Denver area.

[@ProPDRofGa]

@@williamwhitley7969 call Ron Kronon and tell him Stephen in Georgia referred you. I’ll send the link to his website. www.autoflexhail.com

[@williamwhitley7969]

@@ProPDRofGa Thank you,nice work on that truck.

[@ProPDRofGa]

@@williamwhitley7969 I appreciate that 👍

[@polojay5169]

How much was quoted for this exact repair ?

[@ProPDRofGa]

I’m sorry but I can’t remember on this one, safe to say it was considerably less than a conventional repair at a body shop

[@DS-rp9di]

This video is weird he tried to say it’s not fake…ok well I hope so…but then speeds up the entire repair and doesn’t show any technique. What’s the point of this video? How tf am i supposed to do that?

[@ProPDRofGa]

You’re not supposed to do it, you’re supposed to call a professional company that performs these repairs….this is not a DIY video….you can’t fix this even if I handed you the tools and stood by you telling you what to do. It takes years of training to fix damage like this.

[@Wayne1952]

Music is louder than your voice, Can't hear a word you are saying...........

[@ProPDRofGa]

Sorry about that, thanks for the feedback