Whole House Water Filter Installation

Installing a whole house water filtration system. Filtering out fine dirt, silt, sediment, and total suspended solids (TSS).
𝗔𝗺𝗮𝘇𝗼𝗻 𝗔𝗳𝗳𝗶𝗹𝗶𝗮𝘁𝗲 𝗟𝗶𝗻𝗸𝘀
¾” Water Filter Housing
geni.us/yBml
1” Water Filter Housing
geni.us/EASze
1 Micron 20” x 4.5” Filter
geni.us/a6GSp
5 Micron 20” x 4.5” Filter
geni.us/ZjiICsd
𝗦𝘂𝗽𝗽𝗼𝗿𝘁
Want to support my channel or give back? Help me improve on these DIY videos by making a financial contribution. All contributions no matter how small are greatly appreciated!
ko-fi.com/prosdiy
Thank you!
𝗖𝗼𝗻𝗻𝗲𝗰𝘁
More DIY videos! www.prosdiy.com
Facebook: / prosdiy
Instagram: / prosdiy
Subscribe: / prosdiy
Amazon: www.amazon.com/shop/prosdiy
Disclosure: Pros DIY is an Amazon Associate. We earn a small commission from qualifying purchases through our affiliate links at no additional cost to you.
Videos produced by Pros DIY (www.prosdiy.com) are provided for informational purposes only. Please check with all national, state, provincial, and local codes and regulations before attempting any work. Pros DIY does not assume any responsibility or liability for any damage or injury from the information provided in our videos. Please hire a licensed, certified, professional.

[@PROSDIY]

𝗔𝗺𝗮𝘇𝗼𝗻 𝗔𝗳𝗳𝗶𝗹𝗶𝗮𝘁𝗲 𝗟𝗶𝗻𝗸𝘀 ¾” Water Filter Housing geni.us/yBml 1” Water Filter Housing geni.us/EASze 1 Micron 20” x 4.5” Filter geni.us/a6GSp 5 Micron 20” x 4.5” Filter geni.us/ZjiICsd Disclosure: Pros DIY is an Amazon Associate. We earn a small commission from qualifying purchases through our affiliate links at no additional cost to you.

[@marcusscott4897]

where did the gauges come from?

[@natehuber3]

Links are broken

[@daoudatoure1991]

Cool

[@CalebNorris16]

If I am using a large rock well cover could this be done outside near the submerged pump? There is no room under crawl space where my air tank is at and the Only other option I have is in the garage. Builds put the hot water heater inside a elevated separate cabinet like area but it would not be easy to get in there to plumb or replace a filter as needed.

[@boenrichardson7894]

As a plumber just gotta say wow. You are very very thorough with your work and I've never used cushion clamps lol very well crafted and very clean work. Only think I'd do is use a silicone lube for that O-ring for easy maintenance in the future. But otherthan that flawless

[@paulbreen5885]

A little Vegetable oil on your finger and wipe the threads and o-ring seal works perfect.

[@KP-sg9fm]

Thanks for showing all the little steps like doping and clamping instead of cutting them out. speeding it up but leaving it in was nice

[@eugenebernstein5993]

Two comments: 1. You do not mention the process of changing the filter cardridge. We had a whole house filter installed 6 years ago when our house was built, but the plumber did not leave the instructions for changing the filter cartridge. I found the instructions online and, for 5 years, in accordance with the instructions, I went through the laborious task of draining all the pipes in the house to relieve the pressure so I could remove the filter housing. Finally, a plumber told me I could just isolate the filter by closing the valves on either side of the filter (which were incorrectly labeled), pushing a button on the filter to release the pressure, and removing the housing. The whole process takes me 5 minutes now. 2. Buying cheap filter cartridges on Amazon saves no money because they only last a few weeks and do a poor job. That same plumber told me to buy the original manufacturer's brand filters (Watts Pure Water, in my case). They cost 4 times more, but the water tastes much better and they last about 3 times longer. If you are going to have a water filter, it is worth spending a little extra money on the cartridge to have cleaner water. I hope this information is helpful.

[@jaimedpcaus1]

You did an excellent job in the plumbing and set up of the filter. Thank you for sharing. 👍

[@larryseibold4287]

good video. one added note: to test the delta P across the two gauges, the water needs to be flowing at that time, so you need to open a faucet (say 2.5 gpm) and then read the delta. if greater than 10-12 psi, replace.

[@ledzeppelin1212]

Good tip. Thanks!

[@Adambossonyoutube]

Was going to comment how the gauges would show the same pressure but yes if you run enough water in the system that should show if the flow rate is low thru the filter and I would do a two faucet test.

[@urbanturbine]

yes exactly. when there is no flow, gauges will show exactly the same pressure unless their calibration is off.

[@joesanchez4895]

Great video! The Teflon tape and pipe dope is something I did myself today. Used straight Teflon tape and well I had to take part my connections and redo them I was using nylon fittings. Like the gauge idea 💡 Thanks for the share

[@williamworkman131]

Really appreciate it. Been trying to determine what is overbuilding and what is not, so I appreciate you showing the system you chose.

[@michaelcorrea2547]

I googled how to install a home water filter and I picked yours to watch / learn. I will say you made that look so easy which I am sure it was for you. I might attempt it but will definitely need to watch your video as I am doing it. Thank you.

[@PROSDIY]

You're welcome. If you decide to tackle the job, make sure to take the time to plan it out and get all the fittings you think you might need. This will help make the job go smoothly. Good Luck!

[@jusokicin8105]

You don’t need any gauges

[@nsmcastillo326]

Do I need a valve on both sides?

[@thehoss]

​@@PROSDIY I had everything all planned out, but after watching your video I realized

[@Adones09]

You went Above and Beyond, as any homeowner should do. I had to explain to my GF (she was getting home upgrades done) that if you don't tell Contractors how you want it, that they will do it the easiest/cheapest way possible.

[@Beniamin6665]

Indeed. This chap is pretty good. I would recommend having the water tested and of affordable install associated filtration systems that apply. UL, Iron, water softeners, carbon and Ro filtration systems should be consider based what kind of water quality your looking for and where you want the water. To what fixtures. He did a good job on the renovation of this place.

[@evanschneider1959]

This is exactly what I was looking for and more. Thank you for the comments on the electrical system in the room as well. Safety First!

[@dexterrlawrence2280]

Great job...especially with the copper work on the boiler the soldering looks perfect well done

[@CalebNorris16]

Awesome to see a nice area with all your home utilities coming in.. wish I had a system setup like this.

[@tonyturner487]

Well done sir, well done. Ole boy used cushion clamps on the brass- goes to show a nice, fine touch is added to his workmanship. It’s refreshing to see more and more people “give a shit” these days. 🤜🤛👍👍👍

[@PROSDIY]

Thanks Tony! I appreciate the kind words. Cheers!

[@Ragnarou812]

Super good video and a very nice installation! Much appreciated. I learned proper planning and common sense is the key. As you said, who would put water lines above an electrical panel? Yep, attention to details especially the big ones! Thanks again....Tom

[@rogerwhiting9310]

First time watcher and now subscriber. I did a similar job using Propex. The things I learned...use heavier screws than drywall screws. Second...put some lube on the filter canister threads and rubber top gasket. In a year its going to be a bear to back the canister out to service using a flimsy plastic wrench. Good video.

[@johnc8112]

I installed a whole house water filtration system 15 years ago. Water tastes better. Keep up the great videos.

[@denhaagtrader8781]

Hi John. Do you find that the kettle and water in general is better. I guess what I'm after is making sure it clears all the toxins away in it. What brand and one did you go for and would you say it's a good investment?

[@johnc8112]

@@denhaagtrader8781we have a UV Light Tongen, that is what clean the water from Bacteria. Hold house Filtration system. 🏠 and lastly we have a Water softener. The best investment ever.

[@janetyeoman1544]

Nice installation on a rural home. Love the Robertson screws👍🇨🇦. Our filter system also has the UV light 👍🇨🇦

[@rentcda]

Do have a filter downstream of the uv lamp? You might want to consider it. You need a filter to catch the microorganisms you destroyed.

[@frankrazzano5626]

Ygyyiiîô

[@danieldawson222]

Loved how you supported your piping,true Pro!

[@vladorlovsky6623]

Great video. Excellent idea on having a bypass line. I’m definitely going to install this filter at my place.

[@torque122]

Outstanding video. Thank you. I plan on putting this into our new place this summer.

[@Flowrezzzz456]

Super clean. You made this look easy.

[@clintonmiller4917]

Real nice job bud. Appreciate the knowledge

[@Lafue108]

Clean install. Remember to change your clear filter housings every 5 years or as recommended by the manufacturer. Clear housings have a tenancy to crack over time and do have a service life. Also, while the pressure gages are cute, those things tend to fail in 2-3 years. You usually can tell when the pressure is low just by using the faucet. Lastly, going straight to a 1 micron filter doesnt work in many well water situations. I know most have to start with a 25, then a 5, and if really desired, put a third housing for 1.

[@kdr-ql7pz]

Do you have an example of a system you are describing? I'm looking at replacing the big three tank system original to my home. tnx

[@mikejoyce3782]

The Clear housings also have a lower PSI rating than the Blue but are still within the ratings of most residential systems. Put a healthy dab of silicon grease on the sump threads. The tightening of the sump with the wrench is about 1/8-1/4 turn only.

[@NewHomeTech]

Great vid and you made it look so easy, was going to pay to have someone install might just do it myself now!!!

[@dreamingtree]

This was very helpful! Thank you

[@ABobsLife]

Gearing up to do this on my house. Thanks for posting this video.

[@tcwhite0104]

WOW you did a great job on the boiler

[@killaclownz911]

Great video, thanks for your energy in making this sir!

[@parvizfathianpour9509]

Hey man, you did a good job. Thanks for sharing it.

[@user-iv9zz9dj7x]

Thank you for this. Just installed one in my home with the help of this video

[@ragetotheend]

real art right there. thx for posting

[@bobt471]

Excellent video and demo! Thank you !

[@ledzeppelin1212]

Very helpful video, sir. Thank you!

[@bryankoontz6210]

Thank you. This was helpful. You did a great job.

[@KhmerUSA999]

I don't know you are a plumbing or video creator. but you did very good job on both thing. it's very clear enough. thanks

[@JohnSmith-cq3io]

Super work 👍

[@chelsea08FC]

You're an expert. Great video

[@jaimemendoza5163]

Nice job!

[@rudyhaber5536]

Excellent job and video!

[@VIKING33NY]

Great Video. Thanks!!

[@arabiantxn]

Thanks for this amazingly informative video

[@jasonhetke141]

thank you for such a helpful video!

[@giovannipg3000]

Great done 👍👍👍

[@roycraggs2058]

If you suffer with silt in water, then perhaps two-stage filtration a better idea, especially if you intend to use a UV unit post filtration. 20 micron filter first, followed by 5 micron filter pre-UV. Opaque filter housings will discourage any algal growth in filters, which should be changed at least 6 monthly.

[@brianskellenger9344]

Which brand?

[@cageordie]

Not really an issue in a dark basement, and you give up the ability to check the filters visually, which probably means more clean filters get discarded and make more money for manufacturers.

[@bryansoto6355]

Awesome vid!!!

[@ezrastevens4254]

Awesome Job bro

[@PearsonParty]

Well done, thanks!

[@mds6387]

I went with building a 2 stage system since the city likes to over chlorinate the water in the winter. I'm running a 5 micron sediment filter in front of a 5 micron carbon filter.

[@mattrosich]

Ya that 1 micron filter is gonna need to be replaced so often. A 2 stage system is way better. Even a 30 first then 1 micron 2nd works so much better. Depending on your sediment pre filters of course

[@AequitasSaints]

My city also over chlorinates their water too. What's the best ideal setup if it's really just chlorine and not sediment issues? Same as you described? Whats the effects on chrloine with CPVC and pex. My house is all CPVC but I just got the tools to do PEX A and I want to go that route with everything eventually. I heard pex doesn't like chlorine idk about cpvc though.

[@Akuza1000]

i installed 3 of these outside in the vegas sun. The system being 20" allows normal flow. Combined with Pentek filters... sed, carbon block, MAG-chlorine-iron. does well. The idea is that the UV and heat will destroy anything the filters may have missed. filtered to 1Micron. Clear casing. 1 1/4 fed lines. filter the 4000 sqft home easy.

[@gleiverperez1953]

Beautiful

[@myvideossuck7114]

Nice install 👍

[@PhucNguyen-ph6ez]

You did great

[@Bear0328]

Thank you 🙏🏻

[@lou704]

Nice job.

[@NYSIXFIFTH]

Great video!

[@mrmike6523]

This whole set up makes me wanna learn soldering techniques for plumbing

[@MikeHuntz810]

Awesome video

[@jayescreations489]

very good. I want to add a filter to one like you put in.. my iron has dropped to .8 ppm and will try with second filter to see how far iron will drop .

[@wellsyaknow]

Should install the viega system for your water it’s amazing

[@shiningstone9451]

great job, nice video!

[@keithswim]

very useful. thx.

[@mindseyewatering6635]

Well done video. I installed two of these in parallel on my well system to avoid ANY drop in pressure. I also use 5 micron carbon block filter elements. I was seriously considering the use of pre and post pressure gauges, but with a parallel filter system, they may not show any differences until LONG after the filter elements need to be replaced. I simply change both elements at a 1 year interval.

[@raysmusic49]

Did it work? Im thinking about doing that on my well

[@mindseyewatering6635]

@@raysmusic49 Yes it works great. I'm using the large 4.5" x 20" filters and I change the elements once each year. I also have a UV sterilizer and my last water test at a commercial lab was excellent.

[@casinoBALTIMORE1]

Well done

[@leonidviktorov1354]

really cool!

[@Patrick-pl8wv]

Great job.

[@meanjeand1608]

Nice video!!

[@ericeman1093]

bro this is awesome

[@ronaldmendoza3594]

Good job Mr Plumber keep safe and God bless

[@PROSDIY]

Thank you George! Cheers!

[@frankripley5188]

Super video!!!

[@jobo911]

thanks for sharing

[@truckingpix]

thank you great video!!

[@DilnuwanAmaraweera]

thanks you

[@10469]

Good stuff!!

[@ronwatson6637]

Fantastic video

[@JohnvanGurp]

I’m impressed that your wife let you use that towel while assembling the joints! :-)

[@mattrosich]

Hahahahaha

[@WiSeNhEiMeR-1369]

Thanks COOP ...

[@1stNeoSpartan]

Pretty good thx

[@sheaohara6969]

Awesome video man! Clear quality, thorough explanations and neat work. New subscriber here.

[@PROSDIY]

Thanks Shea! Cheers!

[@annettetorres2193]

great video Thanks

[@juvenaldominguez7022]

Nice good job.

[@Scratchingforcash]

Great video, what kind of crimping system are you using for the fittings? Looked pretty good and pretty easy….

[@masterchiefmasterchieflopez]

GOOD JOB

[@sparky5860]

Great video.......👍🏼

[@MrMkapusta]

I was thinking about that PEX above the breaker also. Makes me nervous!

[@PROSDIY]

For sure. Currently working on another video to move all the water lines to a header system and clean up that mess, Lol.

[@MrMkapusta]

@@PROSDIY 👍🏻

[@the1spurs]

Nice video very interesting

[@westend3019]

I'd suggest to place lubricant on the filter canister seals so that removal for filter replacement is easier.

[@nav5897]

Nice 👍

[@im11000]

Thank you for sharing your videos Where did you get the wall mounted cushion clamps from! Thank you 😊

[@elmotherookie]

its a very nice DIY video. as a new DIYer, could you please add the tools you used in making this project. Thank you.

[@highflyer13131]

Great video but you forgot to mention the drain leg for when it's time for a filter change!!! 😉

[@abghere]

Great video and very inspiring! I am a novice in DIY. You make plumbing pipe works look so easy. Are those 3/4" PEX pipes? Is it reachable for a newbie to tackle project like what you shown and/or adding a water softener? Is PEX easier to work on than PVC or vise versa. What about cost and time?

[@frenchclaret9892]

Wow...you are pro

[@NotRiansLuke]

This is exactly the video I needed -- thanks!

[@PROSDIY]

You're welcome! Thanks for the comment!

[@chrimsson]

Awesome video. Question, if I'm tight on space and running the bypass is easier across the bottom of the filter unit is there any problem with that? Previous filter was GE without a piped bypass and it's built in bypass failed. Definitely want to pipe in a bypass on the new one and space is tight

[@jeffm2787]

Only thing I would fault is using the wrench to tighten the filter If it leaks when hand tightened add some food safe silicon grease to the O-ring and also the threads of the filter. Nice Job. Edit: Ohh and the gauges would be read with water flowing. They will read the same when no water is flowing regardless of how clogged the filter is.

[@jamestalbert2900]

Nice Belimos

[@sharnicole1406]

I’ll probably never do this. I didn’t even know what any of this was before the video!!! You did great & we’re very informative.

[@SAW_Coffee]

Thanks for the great walk through on the installation. Do you have affiliate links for the 1" brass connectors, pressure gauges, and shut off valves? I'm setting up a home water filtration system with 3 filters that I've cobbled together.

[@thehoss]

Hey boss, great video. Question and observation. That ball valve you used for the bypass I believe is not rated for pot water use. I considered using that for a setup I'm designing but I saw that it's not rated for pot water. You may want to look into that, it may not be the same valve, who knows. But better to be safe! Thanks for the video!