Pt.2 Honda TRX300 Final Drive Rebuild At D-Ray's Shop

  Рет қаралды 108,467

D-Ray Smith

D-Ray Smith

Күн бұрын

Пікірлер: 40
@mechanicmike2858
@mechanicmike2858 6 жыл бұрын
I know this video is a couple years old but I just want to say thank you I appreciate you taking the time and explaining these repairs in a simple manner thanks a lot
@paulcarpenter7429
@paulcarpenter7429 7 жыл бұрын
Great Video D-ray. Have done lots of 300 final drives. I found that if you work the spring clip around to an open end you can hook it and pull it right out. Then I use an inside bearing puller with slide hammer. Heat case a little with propane. Pinion bearing will come right out. On installing new pinion bear I never reinstall the spring wire. There is no need too as the inside nut will keep it all together. On a final note, I sometime use a speedy sleeve on the crown gear were the seals run because they are usually well grooved and over time will let water back in. Was a very poor design in my opinion from Honda. Keep up the good work.
@larrygreen2831
@larrygreen2831 5 жыл бұрын
I just did both my Honda 420s. I was able to remove the pinion pilot bearing retainer as well through the hole. then use a expandible bearing slide hammer to remove the bearing. I opted not to reinstall the bearing without that bastard wire lock, its a tight fit anyway! Hope this helps!
@theodoremcadow
@theodoremcadow 3 жыл бұрын
Ive got a 85 big red 250es that has the exact same final drive, this video absolutely helped me get mine rebuilt.
@elvisream3322
@elvisream3322 7 жыл бұрын
My free honda trx 300 fw is in poor condition thank you for the videos saved me a lot of hit and miss thank again
@curtwynkoop6085
@curtwynkoop6085 5 жыл бұрын
Awesome information and technique on this project ! It will help me on my atv.
@roberthowse6337
@roberthowse6337 8 жыл бұрын
Great Job. I really like to see you do stuff like this, The Explanations are Exceptional.
@mc8305
@mc8305 2 жыл бұрын
Nice videos and I like the custom tool ya made that’s a good idea thanks for sharing
@dangolden5696
@dangolden5696 7 жыл бұрын
Great video series thanks so much! really helped with my final drive rebuild. Turned out perfect. but did take some time. Thanks again!
@SteveRobReviews
@SteveRobReviews 8 жыл бұрын
Now that was slick. 👍👍
@RednecksGoneWild
@RednecksGoneWild 8 жыл бұрын
Put a new water pump in my 93 Mariner 40 today , Just wanted to sat Thanks for the videos, Helped alot.THANKS
@tomclark3592
@tomclark3592 4 жыл бұрын
Dam good teacher! Great quad side manner.
@liddell157
@liddell157 8 жыл бұрын
I'm glad your back making videos
@charlesgrady7189
@charlesgrady7189 6 жыл бұрын
Hot wemon
@charlesgrady7189
@charlesgrady7189 6 жыл бұрын
liddell157 and
@charlesgrady7189
@charlesgrady7189 6 жыл бұрын
Milf
@charlesgrady7189
@charlesgrady7189 6 жыл бұрын
Milf
@zx8401ztv
@zx8401ztv 8 жыл бұрын
Hey your tool was a good idea, i suppose if it was a more regular job you could get a bigger diameter bolt and file the end to fit the ark of the bearing outer. Full contact between the end of the bolt and locking ring may make it a bit easyer :-)
@ericneering6357
@ericneering6357 2 жыл бұрын
I’ve done it twice now without drilling a hole you need a really long and skinny skinny drift punch
@dennisdyg2887
@dennisdyg2887 Жыл бұрын
Thanks, good, informative video
@Joe-tz3un
@Joe-tz3un 3 жыл бұрын
Thanks for the information
@jayschwartzenburg4708
@jayschwartzenburg4708 7 жыл бұрын
Thanks great video helped so much!
@misticheeks9892
@misticheeks9892 8 жыл бұрын
HI, It's me again. thanks for your video's. I am working on my '96 honda 300 as we speak and I have the 2 bearings & seals for the case, but UNFORTUNATELY it turns out its my pinion bearing. (my luck) Just wondering if u may know the # or the dimensions for the pinion bearing I need? I am learning alot from you & just wanna say Thank You So Much!
@RonaldHambrick
@RonaldHambrick 8 жыл бұрын
Special tools? We don't need no special tools! We make 'em ourself!
@MrRbt61
@MrRbt61 7 жыл бұрын
work clip around -find end - hook up - pull with pliers
@gadsdenviper7149
@gadsdenviper7149 7 жыл бұрын
I normally take a carbide bur and cut the race in 2 and the pieces fall out.
@nickchialOG
@nickchialOG 6 жыл бұрын
Gadsden Viper your suggestion was a life saver great tip!
@zozimodelacruz4062
@zozimodelacruz4062 4 жыл бұрын
MUY BUENO - DIDACTICO
@JOCO1911
@JOCO1911 6 жыл бұрын
Would you happen to know if the rear axle bearings are the same size as the front?
@shelbygraham1795
@shelbygraham1795 2 жыл бұрын
I'm doin a rebuild on a 85 big red that little bearing on mine there is not hole it's got a circle but no hole where Iyou can see a circlip do I need to drill a hole down to a circlip or is there one on this year?
@shelbygraham1795
@shelbygraham1795 2 жыл бұрын
5 mins into this video it talks about it
@chrisshepherd4786
@chrisshepherd4786 5 жыл бұрын
i have a 95 honda 300 it runs but cant get it to pull , ive put new clutches all new rear end parts pinion gear and u_joint but cant get the shaft insicde the motor block the one that turns the drive line to turn and i dont whats wrong wth it im not that of a mechanic ..asking for some pointers on mite wrong wth it ,,,,thx
@spacecatboy2962
@spacecatboy2962 8 жыл бұрын
whats the price on a job like this
@jasonkerrman383
@jasonkerrman383 7 жыл бұрын
never showed how to remove pinion gear with needle bearings
@gussgames8180
@gussgames8180 4 жыл бұрын
What does final drive mean
@jeroenoppers73
@jeroenoppers73 8 жыл бұрын
and where are the left over parts
@skulledmonte84
@skulledmonte84 8 жыл бұрын
You have an atv shop with no welder wtf sucks not having tools you need
@mikeshobbiesandrandomstuff
@mikeshobbiesandrandomstuff 6 жыл бұрын
Ruined that differential case...
Pt.3 Honda TRX300 Final Drive Rebuild At D-Ray's Shop
14:24
D-Ray Smith
Рет қаралды 104 М.
Pt 1 Honda TRX300 Final Drive Rebuild At D Ray's Shop
10:32
D-Ray Smith
Рет қаралды 195 М.
Accompanying my daughter to practice dance is so annoying #funny #cute#comedy
00:17
Funny daughter's daily life
Рет қаралды 13 МЛН
Players vs Pitch 🤯
00:26
LE FOOT EN VIDÉO
Рет қаралды 135 МЛН
Don't underestimate anyone
00:47
奇軒Tricking
Рет қаралды 18 МЛН
Pt.2 Honda TRX300 Carb Repair At D-Ray's Shop
12:23
D-Ray Smith
Рет қаралды 252 М.
Pt.4 Honda TRX300 Final Drive Rebuild At D-Ray's Shop
4:51
D-Ray Smith
Рет қаралды 59 М.
Making A Twin Cylinder Engine For My R/C Airplane
34:07
JellyFish Machine
Рет қаралды 280 М.
Pt.1 Honda TRX300 Carb Repair At D-Ray's Shop
13:16
D-Ray Smith
Рет қаралды 606 М.
Seller Wants To Buy Back This $350 Honda 4x4 ATV
41:31
2vintage
Рет қаралды 481 М.