PT Cruiser Head Gasket Replacement Part 2 Removing The Head

This 2008 Chrysler PT Cruiser is getting a new head gasket. This is the second video in this four part series.
😎If this video has been helpful consider supporting us with a cup of coffee! 🙂
www.buymeacoff...
🛒PARTS LIST:
▪️ Head gasket set: amzn.to/3UBQiqF
▪️ Head bolts: amzn.to/3SY4dGb
▪️ Timing kit: amzn.to/48npvRT
▪️ Spark plugs: amzn.to/3SVVhRI
▪️ Thermostat: amzn.to/3uyBVbX
▪️ Coolant: amzn.to/49Bx2xy
▪️ Air filter: amzn.to/4bv4hEy
▪️ Ultra black RTV: amzn.to/49rHTdh
▪️ Dielectric grease (optional): amzn.to/3HDPTMw
▪️ Anti- sieze: amzn.to/42wZ2QS
🛒TOOLS NEEDED:
▪️ Breaker bar: amzn.to/42eP7Pq
▪️ Coolant funnel:amzn.to/4bfMaCk
▪️ Electric ratchet: amzn.to/3Sw4W12
▪️ Flashlight: amzn.to/48OaGJi
▪️ Flex head ratchet: amzn.to/47PZwm7
▪️ Impact socket set: amzn.to/3Hy3fKi
▪️ Impact wrench: amzn.to/3Sfmiht
▪️ Pick set: amzn.to/3u9AdNZ
▪️ Plastic scraper: amzn.to/4bh3oPI
▪️ Plier set: amzn.to/3uhTvRi
▪️ Prybar set: amzn.to/3IkSlWw
▪️ Ratcheting wrench set: amzn.to/48NM974
▪️ Screwdriver set: amzn.to/4b6BZ39
▪️ Socket and wrench set: amzn.to/4b6K8ob
▪️ Three jaw puller: amzn.to/42eB2Sn
▪️ Torque wrench 1/2: amzn.to/3AgaOB2
▪️ Torque wrench 1/4: amzn.to/493Xr70
▪️ Torx bit set: amzn.to/4b5WUTQ
➡️I am part of the Amazon affiliate program and get a small commission when purchases are made through the links provided.
🔺DISCLAIMER
The information provided by Valley Mobile Automotive (“we,” “us” or “our”) on this video is for general informational purposes and entertainment only and does not replace professional advice.
All information is provided in good faith; however, we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability or completeness of any information on the video.
By working on your own vehicle, you take responsibility for the outcome.
Under no circumstance shall we have any liability to you for any loss or damage of any kind incurred as a result of the use or reliance on any information provided on this channel. Your reliance on any information on the videos on this channel is solely at your own risk.

[@sfcd4757]

How much would a decent machine shop charge to clean up and do the head?

[@lysha_chmo]

Mine costed me 560, but it was crooked as hell, and valves were not looking good, but I think the clean up and resurfacing only can cost anywhere from 200-350

[@donovan791]

Do you have to have a machine shop cleean the head

[@catlady8324]

What about blasting (Impact driver) those cam bolts off earlier when the timing belt was still together and then just putting them in hand tight until ready to take the pulleys off?

[@ValleyMobileAutomotive]

@@catlady8324 The room was too small to get any power tools on the cam bolts. Using the hole in the cam worked great! But if you come up with another method feel free to share your experience 👍