Puch Maxi LS - Moped rebuild - PT 3 ( engine cylinder installation ) bbk

In part 3 of the Puch Maxi Rebuild mini series I install the cylinder kit.
It is a Treats 70cc kit.
Feeling generous? Buy me a coffee to help support my videos.
www.buymeacoff...
#puch #bbk #mopeds
Gear Links
Main Camera amzn.to/3qw1Cnt
Main Lens amzn.to/3qsSOPf
Wide Lens amzn.to/3pwmOdQ
Portrait lens amzn.to/32ooNbv
Mic amzn.to/3HgkBch
Light amzn.to/3qw2SXJ
360 Camera amzn.to/3euCkjV
Selfie stick amzn.to/3pxJGJK

[@puchymueller7209]

Nice videos Man we need more like this knowledge is power Man and you got it you going to keep my mopeds alive

[@Corn-ped]

Thanks! I enjoy spreading the knowledge!

[@AlexanderLanderman]

Wish I had this video the first time I did a kit haha. Would have saved me a lot of trouble.

[@Corn-ped]

Same here! I have done so many and there are so many little tricks.

[@VintageGarageYT]

Great work! I like the video quality!

[@Corn-ped]

Thanks! Anything I can improve?

[@VintageGarageYT]

@@Corn-ped Audio sometimes dips, probably because you're a bit further from the camera? I use GoPro POV stuff on my videos so I have the opposit problem. You can hear me breathe sometimes 🤣

[@Corn-ped]

@@VintageGarageYT yeah I m using an expensive shot gun mic and I actually don't like it. I had a cheap one before that was way better. The audi is the hardest part.

[@VintageGarageYT]

@@Corn-ped I know the feeling 🤣. We just have to keep improving! 👍

[@jimmyberubelevesque2557]

Thanks for your nice videos, man!

[@Corn-ped]

Thanks for watching!

[@jamhandygarage380]

at 5:05 did you say newton pounds for the torque unit? anyways good stuff man

[@Corn-ped]

Lol yes I did. Good catch

[@taylornelson3226]

Hey I have the 70cc Airsal kit that I just slapped on my maxi. It runs. My only question is it seems like the piston doesn’t retract back far enough to open the intake port up. Maybe my understanding is off but wouldn’t this not be able to run if that’s the case?

[@Corn-ped]

On a two-stroke piston port engine the Piston skirt raises above the intake port and the mix goes into the bottom of the crankcase and then up into the cylinder through the transfers. The Piston does not go lower than the intake port.

[@basillane1130]

question! my kit is leaking around the bottom of the base gasket. my kit came with two different base gaskets. one thinner and the other thicker. i applied two stroke oil onto the gasket before installing. everything is torqued to spec. what would you suggest i do? i have ultra grey permatex but i’m not sure how necessary that is. stack the gaskets? idk.

[@Corn-ped]

I would check the mating surfaces for any scratches. You can use the thicker gasket or cost the gasket in copper spray for ultimate sealing.

[@Pigmaster6373]

Love big bores. Wanting to take my Lifan 125 to a 143. My Honda passport c70 went from 70cc to now nearly 100

[@Corn-ped]

Get that Daytona 190

[@Pigmaster6373]

@@Corn-ped just that statement alone made my wallet cry

[@zakpaine]

What type of oil are you using to lube the piston and chamber? Does it matter? Should I use assembly oil or simply some 2 stroke?

[@Corn-ped]

I am using assembly Lube but using two stroke oil works just as good

[@zakpaine]

@@Corn-ped ok, thanks for responding. I am going from stock 38 to 45 and the piston fills the engine in a totally different way, when I spin the fly wheel it’s a much different sensation, lots a compression when the piston reaches the head and I wasn’t sure if maybe the assembly lube wasn’t too tacky.

[@Corn-ped]

It probably has a lot more compression than your old piston!

[@zakpaine]

@@Corn-ped that’s what I figured! Just don’t wanna get it all put back together and discover I’ve screwed the pooch! Thanks a lot for your videos, you’ve been a big help.

[@austinlongable]

Are able to link the kit you purchased?

[@Corn-ped]

www.treatland.tv/puch-70cc-cylinder-treat-kit-p/puch-treat-kit-70cc-the-people.htm this is the kit!

[@BK-tp3sg]

I got the same kit. Was there no porting or case matching required? Any info would be appreciated it’s my first time

[@Corn-ped]

this is a really basic kit. If you want to take it to the max you should Port match and case match. But you do not need to no.

[@mikecandel5446]

What head did you use?

[@Corn-ped]

This is using the 79cc oring head from treatland.tv

[@puchymueller7209]

Where do you get your parts and stuff is there like a good website

[@Corn-ped]

Yes! Treatland.tv for almost everything!

[@puchymueller7209]

Thanks man !

[@puchymueller7209]

Dang there's so much good stuff thanks again keep the videos coming

[@Corn-ped]

@@puchymueller7209 oh man! Yeah so much good stuff! Sign uo for the email news letters they have a 15-20% sale every holiday. So next weekend should have a big labor day sale!

[@puchymueller7209]

Will do

[@wildwespocketbike]

Great video

[@Corn-ped]

Thank you!