Put ATX motherboard into ITX case! | Ssupd Meshroom S Build！

[@YXY703]

RIP Seasonic, you was a good psu...

[@bobbymoss6160]

Really like the power connector placement on the GPU.

[@ireanz8600]

How did you use your ipad as a mintor for your pc?!!

[@noobtechtv]

I wonder how the PSU will get air to cool?

[@johngonzalez9621]

It can’t!! 😢

[@ohman4025]

from the imaginary air flow

[@Dougyen]

It sucks in glass panel

[@dregoes9273]

You can flip the psu in the opposite diection and it can intake air from inside the case.

[@sonofulti1337]

Don't worry, most of these KZbinrs that make these videos just take them apart right after they finish making it. It's not used

[@whiskeredshrimp]

love the way the gpu looks!

[@cryonic.]

meshroom is such a nice case, i wish the mesh panels were more rigid though

[@sbmartinbergeron396]

Very nice build. Just finished mine but I put the GPU in the front and the PCU in the back. no cables exposed!

[@MohondhaY]

Was it a sff gpu, mounted horizontally?

[@nicolasn9245]

hii dude, is it possible to get a photo of your buid with the graphic card in front of the mb?

[@keibohow69]

Looks good, but glass panel psu will choke, no air moving over vrm or m.2 where are the tempe😊

[@TallneckTech]

You can always cut a few air holes into the side panel, but depending on the thickness of the glass it can crack fairly easily. M.2 and Vram should be ok, hot but fine, probably idling around 10 C higher than if there were fans blowing air onto it but the heatsinks on both should cover it.

[@pouringpoipoi5777]

you can always buy addon of mesh side panel to replace the glass panel

[@namitu3d]

@@TallneckTech it's tempered glass... you can't drill holes in it... because it's tempered glass with an increased surface tension...

[@JohnDiew]

the tempered glass is sold separately, no one in their right mind should make that purchase

[@ahvamp]

你的Riser Cable是多长？

[@enelle5380]

Am I crazy or the MB did stuck out then somehow it didn't, and magically fit into the case later on ? 3:35 - 3:43

[@herzonbien7012]

I noticed it too but I don’t understand how it fit.

[@jerryknudsen7898]

maybe flip the power supply, it can't get airflow and the VRMs on motherboard are also in still air. Beautiful build, but everything on the left side is going to heat soak, maybe if the power supply is flipped it can pull atleast promote a little airflow from the m.2 heatsinks, VRMs, and also cool itself in the process a little.

[@mr.electronx9036]

in theory you can... there's no holes for the screws. you need to make your DIY bracket or something

[@Seizuqi]

Oh that is so awesome! i have been searching for a sff atx case, great vid :)

SSUPD just copied my case mod :)

[@TheSuperDuperLS]

You do realize it is possible for two people to have the same idea. People doing that same thing doesn't necessarily mean they're copying, they could have just came up with the idea not realizing someone else had already had it.

Maybe it's exactly what you think. But if I look closely at every detail, I have the right to doubt it - it's perfectly similar.

[@namdinh7192]

I wonder how PSU fan get air flow if this case does not have mesh panel instead of glass one ? will the AIO radiator het hot because of hot air from GPU ?

[@Kage0No0Tenshi]

whats diffrance between SSUPD Meshlicious TG vs Ssupd Meshroom S ???

[@thewop0628]

considering cable mgmt is meh, and the psu fan is so close id have stuck with the mesh side panel

[@kameiakaishin8004]

how was the thermals? 4-6 hrs usage?

[@GloomyOrange05]

what tools do you use?

[@MyEvilVlog]

а куда выдувает блок питания ?: или что он вдувает ?

[@TewaAya]

Psu dead by that glass if used too long. I might buy this case and make diy/3d print attachment for eatx case.

[@bharatbyan]

can you share which riser cable was used ?, length of the cable ?, stock cable came with case ?

[@mr.electronx9036]

440mm

[@georgeconstantinides7619]

hello friend. how long is the pcie4 riser cable that you have shown on this video to install your graphics card behind the case. thanks

[@curiouslilpanda]

From the research I did, it is a 380mm cable

[@georgeconstantinides7619]

@@curiouslilpanda thank you friend !!

[@user-kou693th9e]

Can Install the radiator 360mm ??

[@shadowr2d2]

Thank you for posting this video 🎥🍿🍺🇺🇸. You have a new subscriber 🎉. Keep up the great 👍 work 🎉. An amazing 🤩 build.

[@WYTLA]

没有价格警察和散热警察的评论区太舒适了(*￣︶￣)

[@namitu3d]

Well, the power supply definitely won't get hot with all the air it can suck in... irony off

[@SamyakGupta-e5q]

The only problem i have is the way the gpu rizer cable is bent

[@Dougyen]

"It was an atx case?" "Always has been" *Gunshot*

[@tondoestech]

I would certainly change the orientation of the AIO fans to pull fresh air from outside and avoid the hot-air recirculation from GPU. Better if it is facing the mesh first prior the rad. Also, since there is no other placement options, I would definitely use mesh side panel over TG. Less visual appeal but more practical in cooling. Flipping it to face the inside of the case if TG use is preferred, to get air from inside the case. Not very efficient, but it'll way more effective than facing dead-on a glass panel.

[@zetter5888]

Unfortunely putting the fans to intake does not yield better temps at all, it only makes the gpu rum hotter because the aio isnt assisting it im getting the air out. Aio intake would be much better if there was more room between the fans/radiator/case

[@ФИКС3Р]

Why it's so loud at the end🤔 and that squeak

[@iam_justbored]

Because the fans ramp up when the PC is started?

[@ФИКС3Р]

@@iam_justbored I watched his previous builds and none of them has that noise

[@arifnurabidin2509]

Tell me is 15liter for matx case , consider a small or just decent?? Im talking acer u300 case Do you have any case recommendations that support matx mobo and atx psu Smaller dan acer u300??

[@Mannerdm]

jonsbo z20

[@apurvgaikwad6203]

Can anyone please tell me more about the gpu riser cable he used? I have asrock B450 motherboard and amd 5700xt, what cable should i use and how long that should that be for SSUPD.

[@curiouslilpanda]

If your motherboard is ITX then you use the one that’s included, if it is ATX then you need a 380mm cable

[@abood_alzbidyE92]

psu say please let me breathe 😂

[@bizklaustdeity3115]

The graphics card will vent its heat to the sides that the AIO fans next to it will suck the hot air into the radiator. Not the ideal combo for performance but this is just for aesthetics.

[@zetter5888]

It does suck in hot gpu air, but the Radiator is so close to the gpu that it actually blocks one side of the gpu exhaust. So it doesnt affect it by much

[@shuginubi]

One of the best parts of windows 11, is that if your CPU has an integrated GPU, you can just put your monitor cables into the motherboard, and do not bother with putting GPU ports. System will utilise discrete GPU accordingly, depending on load. Which means, you can make insane builds/chassis.

[@1337ghomri]

GG airflow

[@FakeName39]

I feel bad for that power suuply

[@mimik9092]

nice build

[@injectionAI]

featuring the psu with a clear panel but not the gpu is a mistake

[@justeddm]

Ncase M2 matx build

[@TechTalkTobi]

in this current build, there is no reason to have an ATX Board. Sorry but no.

[@curiouslilpanda]

The only good reason is when you want to use a good ATX board you already have

[@dalelivingston7312]

959 Sonny Squares

[@geralt36]

The PSU is choked though. A mesh panel would've been better. Not as pretty but definitely more functional.

[@LQSTik]

Если была цель сделать компоновку не выходящую за рамки материнки, то задача выполнена. Только толку от этого мало, охлаждение на нуле

[@graf_andy_s4577]

И зачем там стекло, с таким то видом. Кабеля как лапша в коробке, да и блок питания в глухую стеклянную стенку. Не практично, да и не понятно как себя поведёт водянка 240 в таком пространстве. 😢

[@akumakh00]

]he will never run stress test on it.... it will literally burn

[@vuhoangkhanh6796]

There's no room for cool air inside this case

[@yilongwei4592]

that's ok, because you just take pictures after building and remove all the panels if you actually want to use it

[@zetter5888]

​@yilongwei4592 That is incorrect, it works just fine, it's an itx system not a full tower with 7 fans..

[@yilongwei4592]

@@zetter5888 we call it a "MenGuan" , meaning "heat can"

[@LEK]

SSUPD cases actually have really good thermals. Whats worrying is the glass panel. That PSU will suffocate and fry the entire system. With full mesh panels, there is barely any difference between this case and a mid-tower.

[@mr.electronx9036]

The cable management looks awfull. The AIO is bending like hell and the riser is almost to short. the glass panel will chocke your power supply (should add fans on the side) Case looks nice but the price is way to high Nice white build anyway 👍

[@Kage0No0Tenshi]

wtf! PSU can not take air, swap PSU so it can blow some air from motherbord bottom and pull out.

[@justeddm]

Nice case..weak mesh

[@holyfilipp]

че то выглядит так себе, собирается сложно, зачем такое надо