What is KiwiGrip non-skid coating & how to apply it.

[@bertharris9748]

I tried this on my boat. Couldn’t get it right then I turned on the background music and Voila, got it. Thank you.

[@daveberquist2593]

Lose the background music - just a distraction and detracts from the presentation. Otherwise, great video.

[@frankh3113]

You could do without the music!

[@madalenefrost9235]

Can this be used on vehicle rubber running board? Have had two bad accidents with shoes/boots slipping on the running board of my van

[@PYIinc]

Because rubber is an oil-based product, and KiwiGrip is a water-based non-skid, adhesion might be an issue. We recommend first applying an oil-based primer that will adhere to rubber, and once fully cured, then apply the KiwiGrip. For further assistance, feel free to contact us at [e-mail]

[@madalenefrost9235]

@@PYIinc Many thanks I will do that

[@beckyh8565]

can kiwi grip be painted over anti slip paint?

[@81scoops]

Smooth will this turn out if applied with a smooth roller?

[@PYIinc]

If applied with a smooth roller, the finish will be more of a sandpaper-like texture.

[@kb8wfh]

If water-based pigments are added to the white, how should it be mixed? Will the paint mixer at the hardware store do it? or should it be done another way? Thanks

[@antoinettewilkins4030]

I have two types of nonskid that I want to repaint, one is rough like sand paper texture and the other is an embossed fiberglass surface. Can I use kiwigrip on the embossed surface as well? I'd want to keep the embossed surface and not add any texture to it.

[@PYIinc]

Yes, KiwiGrip can be used in the embossed fiberglass. However, if there is any cracking or crazing you will want to repair that first as KiwiGrip is not a sealed paint. If there is gelcoat present on the fiberglass this will need to be sanded and dewaxed before KiwiGrip can be applied. If you are only looking to change the color of the embossed area I would add 10% water to the KiwiGrip base and roll it on with a standard 3/8" nap roller as opposed to the textured roller provided.

[@jackrabbit5047]

Question: if applying over an old nonskid deck, will just sanding the "peaks" be enough? How do you get into the 'valleys"?

[@PYIinc]

Sanding the peaks will be enough if you are after a medium to aggressive texture. You may need to apply a thicker coat to hide some of the pre-existing non-skid. However, if you want a fine or mild texture, you will need to sand down to the valleys to get a "smooth" surface. Or apply a thick layer of KiwiGrip to fill all the valleys. Then once it's dry, go back and apply another layer of KiwiGrip and use the roller to get the desired texture. This will, of course, use a lot more of the product.

[@danlawson6103]

I have a non skid sand Awlgrip painted deck over fiberglass that is old, what is the recommended preparation for this old surface? Can I paint over the non skid or should I remove it.

[@TheSolargen]

Please show more sanding.

[@peterkacandes5905]

What about applying it on an existing non-skid pattern? What’s the best way to clean and sand it?

[@PYIinc]

To prepare the old nonskid to accept KiwiGrip, scrub the surface thoroughly with a rotary green pad or wire brush, making sure that all the peaks and valleys are well dulled off. Then scrub with boat soap and water, allowing the surface to dry before masking and applying KiwiGrip. KiwiGrip will typically hide old non-skid that is less than 1.5 mm in height.

[@cbiltris]

How do you apply this on a "diamond type" roof? It's impossible to have a flat roof ?

[@PYIinc]

What type of material is the roof? Fiberglass?

[@cbiltris]

@@PYIinc it s Hanse 312 sail boat

[@PYIinc]

@@cbiltris The diamond pattern will obviously show through. You could sand the fiberglass diamond pattern or apply the KiwiGrip very thick to cover the diamond pattern. Here's a diamond pattern with a normal layer of KiwiGrip applied onto it: instagram.com/p/BGlndRSMtR_/

[@sailingbrewer]

It appears my deck was painted with less than good quality paint. Once it is removed do I need to apply an epoxy base primer like interlux primekote and a coat of Perfection, or can I skip the topcoat and apply this directly to the primer?

[@PYIinc]

You can apply KiwiGrip directly on to the epoxy primer.

[@chrisbell1068]

In the video it says to sand the surface to give kiwi grip something to bond to. if the floor is fiberglass will it be too smooth to bond to? would I have to maybe rough it up a little with sand paper?

[@lukemallet916]

Yes!

[@mikebeasley553]

Did you watch the video?

[@bertharris9748]

In a nut shell (no pun intended?)

[@MalamaoTim]

Is it okay to apply new kiwi grip over old kiwi grip?

[@Deniseisnotarobot]

I'm wondering that too. Any answers?

[@bretguidry6603]

I do it and it works great.

[@myboys1986]

hard to see because white on white does show true texture

[@haroldharold3908]

if ive got a deck with fibber glass fibers on the surface is this product what I need to redo the deck and cover the fibbers that make it itchy to stand or sit on?

[@haroldharold3908]

ok thanks that sounds good do you have a video on it and can a mug do a reasonable job of it thanks

[@haroldharold3908]

also do you have a product to do the sealing with. thanks

[@haroldharold3908]

ok thanks

[@outdoortherapy6596]

All the important parts like radius corner prep and removing the tape around radius corners were cut out of the video. Clearly thats the hard part they didn't want to show us.

[@kaydenfranklin4026]

pro trick: watch series on flixzone. Been using them for watching lots of of movies recently.

[@kannonbradley9068]

@Kayden Franklin definitely, I've been using Flixzone for since november myself :D

[@chaimaryan2366]

@Kayden Franklin definitely, been using Flixzone for years myself :)

[@leonardthiago8816]

@Kayden Franklin yea, been watching on flixzone for months myself =)

[@mymobile5014]

Fcking music is dire!

[@2uneak]

Better music next time! No answers to people's questions? I'll skip this product.