QA1 Control Arms - Right Stuff Hubs & Spindles On The Chevelle With Lou Santiago, Garage Insider TV

It's Garage Insider TV with Lou Santiago working on the Chevelle! In this episode Lou gets the ‪@QA1TECH‬ control arms on along with The Right Stuff hubs and spindles provided by First Place Auto Parts ( www.fpautoparts.com ) for mock up. Parts on the table to the frame in this episode plus great tips from Lou along the way.
Like on Facebook! / garageinsider
Follow on Instagram! garageinsid...
Check out the website! garageinsidertv.com/
Brought to you by ‪@Strutmasters‬

[@gregsimon9061]

So glad to see you Lou, been following you forever, the first time I saw you on TV was building a frame for a Mustang.

[@richardwills7768]

Always great to watch a master at work, and someone who knows what they are doing.Great stuff Lou, keep it up...

[@miltonpomales5405]

Always great explanations!!! Keep it up!!!

[@meanskwirl8508]

Good to know

[@shanewright6958]

Great job and Another great video 👍👍🇨🇱

[@scottbejma5723]

Always great!!!

[@williamlikos1996]

I look forward to your videos..

[@goodfellasinc.5648]

The best of the best as always

[@johnguerriero6851]

Keep it rolling buddy and buy a tapered pry bar set to put into the frame hole and jimmy those control arms right into place so the bolts just lightly tap home!

[@tomcampbell4414]

Bearing grease method that works great and takes no tools- that’s my style

[@rushmore8]

Good timing since I am working on the front suspension of my project right now. I see now it would have been much easier to take the body off first!

[@MondayMorningRacer]

How many shirt and bandanna changes are in this one Lou?! (lol)

[@ashleygetterdone5429]

Why on earth would anyone give this video a thumbs down... thank you Lou

[@jasonmenard1073]

Man im so glad you have a shop and your building cars truck bikes. Because of watching you on MUSLECAR you have shown me how to be a better fab guy you taught me a lot and now your doing for your self on KZbin dude thats gnarly ill be checking out etching you do. Thanks again for being a good inspiration in my life. LATER

[@randywright4310]

Thanks

[@saqwedcxz12]

Hammer for seals that is the SEABEE way. CM always.

[@jasonrutledge888]

Breaking out the white board! lol!

[@beeasy4360]

Defogood stuff

[@Jeet_Kune_Do_And_Carate]

Why no cotter pin?

[@jessemarinjr6374]

Hello Lou ,Great to See you on KZbin , Miss You and Jared on your TV show ! I have a 68 C10 with a lowering kit ,that drives Terrible !! Anyway do you Recommend a QA1 coilovers setup for the front & rear on my 68 C10 ? And last question ,ain't No Mechanic by No means ,and I just can't find a Shop here in Vegas to do a Quality Job ? Do you know Any shop that can do a Quality job ?? And if you don't know any shop how Difficult would it be to install on my C10 ?? Please let me know ,because I have Been Screwed on some prior work I have had Done ! NEED YOUR HELP & ADVICE WOULD BE GREATLY APPRECIATED !! THANKS LOU ,GOOD TO SEE YOUR CHANNEL !!! JESSE

[@kevinselesky4303]

First. keep it coming Lou

[@thecontrarian9933]

You didn't pack the bearings correctly. Your technic of putting the grease on your hand is good but you were putting the grease on both ends of the bearing. Just pack the bearing from the wide end or one end until it comes out the other end. Otherwise great show.

[@datrelwashington8894]

0⁰⁰