QCC3008 Programming - ADK Configuration Tool [disable mic / configure tones & GPIO / TWS]

[@joawesome2319]

I just wanted the ADK when I came arcross your channel, I have seen that you provided it. Thank you very much for providing this. I will use your videos to guide me.

[@jonathanreader6503]

Hey, realise this is an older video so you might not see this! First, thanks for the video. I was wondering if you know anything about the newer modules such as the BTM571 and what would be involved to activate ANC on them? Thanks!

[@arduinoapplication7679]

Hi Darie. it's really a good source for me to learn. I brought a bluetooth audio module a few weeks ago. I though it's QCC3008 or somthing. when I received, it turns out that QCC3031. it's also nice as it has Audio broadcast functionality. however i don't have ADK for QCC30XX. if you have the ADK, please share me. appreciate your support :)

[@pablo231089]

Do you know how to increase the sensitivity of the microphone in this module? Or maybe you have access the development guide.

[@규현박-h5c]

Hi, I am your KZbin subscriber! Your videos are always beneficial and supportive to me! Thank you. I have a question. Can I put the audio prompt that I want? I'd like to know how. I've tried it many times, but I've been failing and I can't figure it out. I need a hand.

[@Darieee]

that's very hard to do ... I've never managed to even get close to solving that issue

[@ShtokCustomWorx]

Hey man, what’s Erik’s youtube channel to check his videos out?

[@decee1157]

Hello, did you by any chance play with the USB feature? Been trying to get it to work but i don't have luck with it. It does show up as a audio device but it doesn't pass audio though.

[@olafmarzocchi6194]

I found a receiver (a complete product) based on QCC3034 and I wonder whether I will be able to open it, and if so to access all these settings. I am planning to convert headphones to wireless and I also don't want any microphone functionality, plus I would like to disable ANC (if available) and to equalize for these specific headphones.

[@belakangdepan1235]

can this module use the party mode feature, and can this module be connected to a different qcc version

[@razorgcy]

Hey there. I've bought this QCC3005 module on AliExpress with an AUX in. I know that this specific Qualcomm module supports two inputs, and one is this AUX interface on the board, which it reverts to when there's no Bluetooth devices connected, which is perfect. However, I want to add a microphone to the second input and use it as handsfree in my car (yes, the output of the module is going to be connected to the AUX IN of my car head unit). However, out of the box this module does not support/show "Phone Calls" on my Android phone. Which setting is it to enable this feature. I know Qualcomm QCC3005 definitely supports it.

[@nguyenkim3616]

Will you upgrade to qcc 303x or 51xx?

[@noxdesignkorea]

I saw your wonderful video, I'll do the same. Thank you.

[@JoseNavarro-xy1po]

Hello, Thank you for your informative videos. I now also have a QCC3008 and would like to activate a PIN, which unfortunately I am not able to do. I have experience with CSRA64215, CSR8645. Maybe you have an idea. Thank you Jose

[@Ariel-mq1pg]

CSRA64xxx and CSRA63xxx Tools v1 is deleted. Do you have an alternative link?

[@Cecio1297]

Hi Darie, thanks a lot for these videos and for sharing your ideas! I successfully programmed a CSRA64215 for being used in a car's radio mod. I would like to program the module such that, when in a phone call, it uses the car's audio out and the phone's built-in mic as input device. Do you know if it's possible to do this using this ADK Configuration Tool? It's less elegant, but the only way in which I managed to use the module also in calls has been by connecting a condenser microphone to it.

[@Apodasch]

Hello Darie, Thank you for sharing your knowledge. Do you have any clue how to get the sw you are using? I cannot find it anywhere on the internet but I would really like to configure my pair of qcc3031 for TWS. Can you help somehow?

[@grindfi]

hey i love you for sharing this bro

[@UnH1ng3d]

Do you know which setting is responsible for it going to sleep when a stream stops? My problem is that it takes too long to start up again when using my phone for satnav, I get the first half of an instruction cut off while it wakes again. I tried both settings under "silence detection" but I don't seem to be able to stop it sleeping.

[@theAGanimators]

Hey Darieee, long time no talk. Just wanted to chime in here and concur with J.A.A on this ridiculous new un-mute setting that HYT programmed in on these QCC3008 modules (apparently to try to reduce the level of the hiss between songs?). The previous HYT CSRA64215 modules did not mute out the first second or two of the turn by turn directions like this one does. The delay is so awful on the HYT QCC3008 module that I harvested an older HYT CSRA64215 module out of another speaker that I built two years ago to use in my car. For those like me who haven't ventured down the road of reprogramming these modules, the HYT CSRA64215 did not have this "slow to unmute" problem and is much better for car use if you ever use navigation. I did a before and after test with my Pixel 5a and the difference in the delay on the QCC3008 and CSRA64215 modules is enough to tempt you (or a novice driver that you loaned your car to) into a wrong turn with Google driving directions. CSRA64215 example: "In 500 feet, turn right". QCC3008 example: "Turn right"

[@Darieee]

wow ... that sounds super bad .. Glenn - do you think you could do a short video on this? maybe even with the navigation use case I can probably send it to HYT to have a look

[@james_robertson]

Hello, does anybody know if this video also applies to the qcc3005? Edit: an AliExpress seller confirmed to me that the adk config tool will work with it (module name: RRD-305)

[@benhonna]

Share me is a peer device function like TWS, but the volume & eq are not synced between devices. Share me may be able to connect to more than one peer, not sure on that though.

[@Darieee]

alright so is that like a simpler version of TWS ?

[@DAVIDsh97]

Just one question. Is this module configurated from fabric to be solded directly for BT-audio proyects, or needs programation first? Thanks.

[@Darieee]

it comes programmed in a usable state; its name will be "QCC3008 TWS" or something similar, but you can use it as is

[@DAVIDsh97]

@@Darieee thanks

[@biggityboggityboo8775]

Do you need the CSR USB programmer specifically or will any USB>SPI bridge work?

[@Darieee]

you need custom drivers if you want a generic programmer to work 🥶 there are some available for that FTDI breakout

[@biggityboggityboo8775]

@@Darieee right then the CSR programmer it is! Thanks for replying.

[@theorginal9952]

Hey dude... wanted to let you know that your video on using DSP helped me great without which I could've never completed one of my project. Could you please make a video on using the DSP of QC30xx series. Also share the KZbin channel of Eric. Cheers!

[@Darieee]

stuff on the qcc3031 will be coming in the future erik's been notified and will get his shit together 🔥

[@theorginal9952]

@@Darieee Many thanks! I've read in a forum that QCC30xx series and maybe even QCC51xx require TRBI200 programmer instead of CSR USB-SPI programmer. Is it true? Were you able to tap into the QCC30xx series with the CSR USB-SPI programmer. TRBI200 is pretty expensive burner

[@Darieee]

I haven't touched any of that yet - the HYT modules do have the standard SPI header though so - maybe that still works

[@theorginal9952]

@@Darieee Oh I see. I'll be waiting for your video then. Cheers!

[@Darieee]

kzbin.info/www/bejne/aau0oGSdhLNnl68

[@RetrospektiveAudio]

Hi @darieee, will this work for the QCC3034? can you link the ADK Config Tool + Fullchain again?

[@3rutu5]

I would like to know similar, i just picked up one of these units.

[@RednasAart]

Hi there I'm trying to install the ADK Configuration Tool but it's just not working. What do I do wrong? I just can see the QCC300x Blue Lab, that's all. Kind regards Sander

[@Darieee]

hey Sander .. no idea .. I never got around to accrue the time and energy to dive into the ADK :(

[@sidhunp]

Using FTDI USB-Serial adapter i am able to connect and use PSToll and UFE. But NOT ADK Config Tool. It needs either the real CSR Programmer or HID (USB) transport (Info from QCC3007 data sheet, can share if anyone wants but it is available online). trying to connect USB with a regular data cable did not work. either i have issue with 3v3 at which QCC USB lines work, HID need to be enabled, or i do not have drivers. People in comments, any help is appreciated.

[@sidhunp]

@@BalkrishanBairwa github.com/lorf/csr-spi-ftdi You need to make some driver changes. Follow the instructions carefully.

[@randomthings2843]

hi. thank you for your tutorial videos. but, can u make a tutorial using usb-spi-ftdi breakout board like FT232RL? because no one selling CSR USB-SPI Burner in my country.

[@Darieee]

I've only ever used the csr programmer they mostly can be had on ebay com or aliexpress com unfortunately

[@randomthings2843]

@@Darieee yes, i see. btw, i have a sanwu audio with TDA7492P + csr 8635 module. and i see someone selling a QCC3008 module with similar PCB board with 8635 in aliexpress. what do you think if i replace 8635 to QCC3008? because i've found those datasheet from www.tianjiarun.com

[@SturmiHD]

Hello, the Adk Config Tool link is broken, do you have another one? Thanks alot

[@Darieee]

can't check right now - buuut - are you super super sure ? do the other ones work ?

[@SturmiHD]

@@Darieee all links to the tools are deleted on dropbox. I need the one for the QC3008, thanks

[@Darieee]

@@SturmiHD do try it now - I readded the link :)