Quick Disconnect Overrun Clutch For The 8N From Yesterdays Tractors

[@MrCap1813]

You don't have to be moving to raise or lower the mower.... just put the tractor in neutral and let off the clutch which engages the PTO.... at that point you can raise or lower the mower. Once you have the mower up, depress the clutch, put the transmission in 1st (or whatever gear) and git bizzy. I also use a toplink that will keep the mower up without the pto being engaged.... it will also let you set the mowing height so you don't have to worry about accidentally hitting the positioning lever and dropping too low. Been using this tractor and style toplink since I was a kid. They do require more work/knowledge on the operator's part, but you can make your own repairs without breaking the bank, and they are just as safe as any newer tractor out there.... the key is learning to operate them (or any tractor) safely.

[@cbr600rx7]

Dude not trying to be hateful but a lot of your problems are from not knowing what your doing. About 15 minutes of google searches will tell you the N series uses a PTO driven by the transmission and a overrunning clutch is always recommended when brushing with one. Also that hog is definitely on the larger size for a N tractor. On perfectly flat ground or field you can get away with a 5.5 or 6 foot but if your cutting hills or trails a 4 or 4.5 is way better matched and will not push the 2500lb tractor around as much. Your catching a lot flack because 80% of these that are still in use are used for cutting/mowing and as long as you use the proper size overrunning clutch which is usually under $75 they are excellent for that. Once again not trying to knock you or give you a hard time but a little bit of research and understanding your equipment goes a long way. I do wish you the best with the project.

[@goarfang]

I agree and I never use a hog bigger than a 5

[@EclecticHillbilly]

I used to have an 8N but went to a Jubilee because the Jubilee has a live lift (PTO doesn't have to be engaged). Makes a world of difference. Edit: They both need the overrun clutch.

[@mikedimond6903]

great tractor raised on one ran brush hog for years when I was 16 plowed driveways in michigan were snow was deep now I'm over 50 and just got another one for our farm yes it's touchy when mowing I just learned to adapt great old tractor

[@backachershomestead]

Luv my 8n and jubilee for brush hogging. I have big steep hills here in Tennessee. The overrun clutch has been around for at least 40 years . Makes a good tractor great. You can buy these tractors cheap because people are scared of them. Just my opinion!

[@tcmits3699]

If possible, over running clutch should be mounted on implement side. No flywheel effect on drive shaft itself, when disengaged, if mounted on tractor side, the drive shaft itself still has flywheel inertia energy, even when first disengaged.

[@robburke8867]

Yeah that’s a better install than the roll pin! Good video!

[@michaelwilson-fn1lb]

Have an 8N. Did not know about the clutch. Thanks

[@TimsWorkshopTJY]

Hi Brett, cool old tractor. At one time we were going to buy 11 acres so was checking out old tractors for sale. The 8N was a common one around here but the most costly even old ones. I was looking at a farmall when we decided to get a place we no longer needed a tractor. Like that your dad can help you

[@billypirtle1443]

Somebody already changed the phone shaft out to the slandered size shaft the areganl shaft was smaller 1 and an 1/8 . You could get the right size shaft back in the late 50's.

[@duanedean3256]

I think its always a good idea for all to take tractor safty. You can actually do it online. One forum i belong to, you had to pass the test before you could post anything. Another thing, learn/research the tractor before jumping on it so there isnt any surprises. This would have helped you figure out, the pto drives the hydraulic pump that makes the 3 point work. You would have also figured out a bush hog will drive a tractor forward without live pto. Because of the momentum of blades. I run a 5 footer on my farmall super c and yes, itll do the same if im not careful. You have to learn the tractor, especially before someone gets hurt.

[@scrumpymanjack]

Hi. Thanks for the video. So does the overrun clutch stop the PTO from pushing the tractor forward after you push the clutch on the tractor down? Is that the main point? Noob here (obviously). Thanks.

[@bucksgarage1]

Yes. It let's it free wheel.

[@scrumpymanjack]

@@bucksgarage1 thanks for the reply and for the explanation. I read that most modern flail mowers have a built-in overrun clutch. Is that your understanding, too?

[@bucksgarage1]

@@scrumpymanjack I haven't ever used a flail mower. I would think that if the manufacturer says the the mower has one installed you wouldn't need one on the tractor side also.

[@crusader777]

Better get a chain for a top link on that brush hog

[@terrybillings7587]

This is not a tractor problem it's a operating problem. you need a manual to teach you how to run your tractor before you get hurt . You do not need to be moving for the lift to lift the bushog. Learn how to use the tools you have or get rid of them before they get rid of you.

[@neildidit]

An over running clutch makes it better, but still not as good as a live PTO. Oliver super 55 and 550 have truly independent PTO with a completely separate clutch and clutch lever.

[@terryhelton4814]

got 8n do have over drive you have to pay atinch to what you are doing if it stats pushing drop the brushhog to the ground

[@TimsWorkshopTJY]

Hi Brett, what do you use for editing you video clips? My software is old and not working very good

[@bucksgarage1]

Windows movie maker. It's not the best but it's free and pretty easy to use.

[@TimsWorkshopTJY]

Thanks Brett

[@TimsWorkshopTJY]

I have it still on my old desktop computer but not on my windows 7 laptop. It has video player. Anyway tried loading a video clip on the desktop the large viewing screen is black when playing the video? It's like it doesn't recognize the mp4 format?

[@bucksgarage1]

@@TimsWorkshopTJY I have windows 10. Maybe try downloading it? I'm not a pro with computer problems.

[@TimsWorkshopTJY]

Got it buy using my photo editor on my laptop. It also does videos too

[@camdencarroll8179]

Hi, do you have the link for this clutch?

[@bucksgarage1]

www.yesterdaystractors.com/S23639_Overrun-Coupler-with-Quick-Release_28714.htm

[@WorldsOkayestFarmer]

Thats a nice addition! #WorldsOkayestFarmer

[@bucksgarage1]

Slow night?

[@WorldsOkayestFarmer]

Brett Buckley it’s been this is actually the busiest but I’m caught up on my stuff

[@sethmalin2895]

5:47 you sound like Johnny Knoxville

[@godmodeforever]

You two are dangerous.

[@stevemedeiros4546]

Dude you need to learn how to use your tractor you obviously bought the wrong clutch I cleared over 20 acres with a 8n I had to put a clutch on it you don't take it on and off it stays on any implement you use will need to stop when you purchase in the clutch it stays on

[@timhaas8917]

Slip clutch