Ford Fusion - Rear Bumper Cover Removal / Replacement (2010 - 2012)

Learn how to remove / replace / install rear bumper cover on Ford Fusion ( 2010 2011 2012 ). Step by step guide on removing / replacing rear bumper cover.
In this video I will show you each screw and clip location and how to remove it. Easy and straightforward. No need to pay expensive shops.
Check out my other educational Ford Fusion videos on the link below. I will be adding more videos with time:
• Ford Fusion (2010 - 20...
Thanks for watching and if the video was helpful don't forget to Like / Subscribe!
⚠ DISCLAIMER:
While QuiteAlright strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. The videos are intended for information only. Follow the manufactures repair procedure and use appropriate safety procedures. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. QuiteAlright is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@jeffmajtyka1695]

Wonderful explanation of how to replace your bumper. Thank you sir. Wasnt to confident until I saw your video. Replaced my bumper in 1 1/2 hours after seeing this. Confidence went from about 30% to 95% after your step by step video.

[@QuiteAlright]

I'm glad I was able to help :)

[@Gerardocaracosa]

Will check my sensors tomorrow morning, thank you

[@QuiteAlright]

No problem 👍

[@xFINITYXRAGEX]

Great video bro very helpful

[@QuiteAlright]

Glad it helped

[@moeoverthere3640]

Exactly what I was looking for, best explanation and straight to the point. Thanks for sharing

[@QuiteAlright]

Thanks for the comment

[@chazits]

Thanks!! for the step x step. I believe this proctdure will work for by '12 mkz which needs some new back-up sensors .

[@QuiteAlright]

You're welcome. Yes it should be very similar to mkz

[@rykerharris2345]

super helpful thanks man

[@QuiteAlright]

Glad to hear it!

[@HauntedMac]

Really helpful thank you

[@QuiteAlright]

Glad it helped

[@chardvelasz1528]

Fantastic, thank you so much

[@QuiteAlright]

You're very welcome!

[@Alycanj]

Great video, tyvm

[@QuiteAlright]

No problem. Thanks for watching

[@Angel-vk3bk]

Thanks man, I bumped into my own truck backing out the driveway and now I need to fix that dent lol

[@QuiteAlright]

Hehe it happens. Good Luck

[@RaulMartinez-jn5kn]

Good video gdeat job

[@QuiteAlright]

Thanks

[@michaelgrady1608]

Nice explainer video, well done. Any issues installing the bumper (other than to just go in reverse order?)

[@QuiteAlright]

Thanks. No issues. Just do it in reverse order

[@anthonycarchidi4704]

Can you show us how the bumper snaps back in on the sides?

[@Regdar92]

Good shit

[@QuiteAlright]

Thanks

[@jaemccain6104]

Would the bumper removal for an SE be the same as this video?

[@QuiteAlright]

If it is model made 2010 - 2012 then yes

[@loukydookie]

Nice video, it is helpful but there are more panel clips in the black plastic panel that is inside the trunk(6 in total). Other than that I think he mentioned all of the rest.

[@QuiteAlright]

Thanks for sharing and for the comment

[@tonycervantes4816]

Good bro. Is of same on 2006/09 ford fusion. made a video to how to remove of front bumper on 2006 /2009

[@QuiteAlright]

Should be the same or very similar on 06-09 Fusion, but I've never done it so can't tell for sure

[@tonycervantes4816]

Ok thanks

[@Shawnjames21]

How did you remove those last 2 black clips? Looks like you have to pry them out

[@QuiteAlright]

Yes just pry them out. Pry out the middle black piece of the trim screw

[@darronsmith587]

What exact screwdrivers did you have so I can go buy them

[@coreybrien9472]

The only one you don’t have is probably the star bit maybe a t-20 you can buy a full set at your local auto shop for not too much.

[@QuiteAlright]

Before removing each screw in the video I say which type or size it is

[@darronsmith587]

I watched the video what was he first screw driver that was used in the video to take out the head lights

[@QuiteAlright]

@@darronsmith587 you need a 10mm socket

[@darronsmith587]

@@QuiteAlright thk u so much

[@timetehkid4198]

It’s been a year hopefully you know that rubber thing is weather striping.