Ford Fusion Rear Bumper Cover And Taillight Removal (2013+ ) Second Gen

[@rccola4494]

It don't get much better than this. I needed to remove rear bumper on 2014 Fusion because someone backed into the wife's driver side rear quarter panel. The impact hit the wiring for the rear parking sensors up against the steel bumper perfectly to cut them clean off. Took about 2 hours of removing … adding wire and soldering to the 6 sensor signal wires. Hooked things up before assembling everything back together and it works. Not very much damage to the bumper … like a 2 inch slit … hard to see so not going to worry about that. Thanks for taking the time to make this very helpful video.

[@Rick_Schott]

Got hit in the back, no real damage but one of the backup sensors popped in. Only way to fix it was remove the bumper cover. Saved this guy a bill from the collision shop! Great video, easy sub.

[@mondeq1]

Sir, I found this video very useful when installing a towbar on a 2015 Ford Mondeo, (EU version of Fusion). I thank you for your time and also the very high quality. At 1.21 where you removed the rear light, I use a cable tie. I fed it up from the bottom of the light in a 2 o'clock direction and the joined it together. This left me with a loop to pull the unit straight off. I feared using a pry tool in case I scratched the paint as I would not be as experienced as you. Again thank you for a wonderful video.

[@happywrenching]

+mondeq1 Glad it worked out for you :)

[@madmaxhornuberdriver7837]

Well, this was exactly what I needed. And great camera work and lighting!

[@andrewproctor8781]

It’s not boring with the clips and nut and bolts, it helps us procrastinators that don’t remember lol

[@velasco330]

Hi Dude, nice going. As you are performing that task, it seems so easy to do. It helped me a lot. Thanks for sharing in such easy way. Best regards from Brazil...

[@happywrenching]

Greetings! Glad it helped!

[@jleau89]

good vid gonna try this tomorrow on a 2018

[@Deathbringerrrrrrrrr]

Did it work? Same process?

[@ForceTranq]

Thanks, I was looking for this kind of video

[@Deathbringerrrrrrrrr]

We need a video removing the trunk hinge arms

[@peterandreadis4864]

This was terrific and super helpful Thank you!

[@DCIROCK23]

I'm very interest want to know how 2014 titanium Fusion led tail work on SE Hybrid?

[@crisgarces03]

I believe it's called the "rear bumper center insert" with reflectors.

[@mikew9673]

thank you very much for the detailed video!

[@bodyshop8008]

Great video! How does Mom like you always taking her car apart to make these videos? lol Very helpful info.

[@joseph_b319]

I wish the front light replacement was that easy.

[@crisgarces03]

Hi, what if the plastic part of the bumper with the red "reflectors" needs to be replaced, is that possible?

[@jigarbavishi1302]

when putting back the tail lights should u hear a click to make sure the unseen screw is fully installed ?

[@batsukamuro]

Thanks for this. Very well done.

[@terrywarnett3270]

Hi, There. Nice Video and this should help me out. Someone scraped the side of my 2016 Fusion and the side has come out at the top where the clips are that you show in the video that just push in? I tried pushing it back in but it will not go. any ideas?

[@question777]

Nice video. Thanks !

[@pcnetworx1]

Fantastic!

[@luisarmenta8034]

This is very helpful thanks guys

[@m2aroz]

Thanks very nicely done!

[@umairmohammed5702]

Top video !!

[@asiajxO]

is there a link to this car part

[@johnlkeck]

Does anyone have a good recommendation on where to buy a new bumper?

[@jasminecrawford5300]

Link to where you ordered the bumper?

[@tomilheirobarbalho6117]

Good job 👍 thanks you

[@zabilbakhshaliyev1783]

Hello guys ! Could be Ford Fusion 2015 rear left fender replaced ? I have damaged my car . Anyone have any video or references? Thanks guys .

[@Relski415]

Will this work on 2006 fusion

[@daeahn416]

If your rear bumper has a sensor, do you have to remove any wires?

[@happywrenching]

If you do have the rear parking assist sensors then there should be a single connector on the driver's side of the rear bumper that you will need to unplug.

[@daeahn416]

Huh? Where is that?

[@Twinjeremy]

those nuts are indeed 10mm not 12 like he said... at least on my 2013 fusion energi it was

[@jimtarter2073]

excellent demo

[@7ALABEB]

Please l want tetinum bamber for se (l want 2 exsust) like tetinum

[@AdmirCustovic]

Great video. Thank you.

[@victoriagkl2173]

Very helpful thank you!