Really helpful video the music was a little loud and distracting but overall pretty good video:)
@BMWarrior1 Жыл бұрын
amazing knowledge and understanding - true expert in their field. Keep up the great work guys!
@RacingDiffs Жыл бұрын
Thank you👍🏻
@PRAGEETHKARUNADHEERA11 ай бұрын
Very well explained. Easty to understand. Enjoyed watching this.
@RacingDiffs11 ай бұрын
I'm glad to hear that! Thank you for the feedback 👍🏻
@georgekrapivko2 жыл бұрын
Love mine!
@lukathegarlic2 жыл бұрын
In one of your E46 M3 videos you said the pinion bearing preload should be 0,6Nm to 0,8Nm. In this video you state 0,8Nm to 1Nm. Why is there a difference now, is this specific for each differential type or is it based on bearing sizing? Also the backlash was said in one of the previous videos to be between 0,05mm - 0,08mm. Now it is 0,1mm to 0,12mm. I hope you can respond, I would like to understand the difference. Why don't you provide crush sleeve anymore but the shim instead? It is a much better solution to put a new crush sleeve in and the cost difference should be negligible. Thanks!
@albobaggins55572 жыл бұрын
I had the exact same questions, the torque spec on the crown wheel bolts changes also
@markdemma7273Ай бұрын
True BMW community legends! Just set my E46 M3 diff up with a new helical LSD and 4.10 gears and the job would have been impossible without the shim pack I purchased from you guys and the knowledge and experience shared in these videos. This is genuinely what motorsports is all about... learn from experience, share that experience, the cycle repeats, and humanity advances. You gentlemen are the real deal. Thank you.
@RacingDiffsАй бұрын
So glad to hear this! Thank you for your kind feedback. This fuels us to push more and make more videos👍🏻
@onesikm3 Жыл бұрын
Great video but I noticed improper use of thread locker! In a blind hose you should always put thread locker inside the hole first then when you drive the bolt in it will actually do what it’s supposed to 😄
@scipperdsbc95212 жыл бұрын
Perfekt 👌
@Oxigan2win Жыл бұрын
Hello - tightening the pinion - is it the same procedure for the 188K 330 CI E46 3.93 diff? Thanks and very very nice video!
@RacingDiffs Жыл бұрын
Yes, pretty much the same👍🏻
@wojtasm52 жыл бұрын
Jak można mierzyć ustawienie łożysk jeśli wymieniono tylko jedno łożysko? Przy kosztach zakupu nowego zestawu kół zębatych to żadna oszczędność pieniędzy. Należy wymienić oba łożyska i dokonać pomiaru i regulacji napięcia. A gdzie pomiar głębokości osadzenia walka ataku? Obawiam się że jest to o wiele trudniejsze jak przedstawia ten film.
@jacklay6867 Жыл бұрын
Mr. May I have a question for you, how much oil to put in the Differential?
@RacingDiffs Жыл бұрын
Put the diff on a flat surface, like on the car. Fill in the oil until it starts to leak from the upper oil plug. Close the plug. For E46 M3 diff, you will need about 1.8L of oil.
@CristianoRonaldo-mv2uyАй бұрын
will this work on a 188k 3.38 diff from a 2003 320ci?
@RacingDiffsАй бұрын
The procedure is similar, but you need different parts. You need the kit that is available in the link below. racingdiffs.com/collections/differential-tuning-parts/products/bmw-gear-ratio-swap-set?variant=40754684133538
@sandpiper15152 жыл бұрын
For your LSD conversion kits how robust are they? Could they be use for "Racing" as the name implies?
@TGLasers2 жыл бұрын
If you are anything serious about racing get a propper LSD core from them...
@RacingDiffs2 жыл бұрын
They are designed for street usage. RacingDiffs is name of the brand, product is LSD conversion kit. 🙂
@doomslayer50442 жыл бұрын
hi guys, i have a question, i have a bmw e39 520i from 96' that has a M52B20 engine, after i did some research i found out that i have a 188k type diff, id like to purchase a LSD set that you guys offer, but im curious to know if i need to grind the spider gears too
@RacingDiffs2 жыл бұрын
The new version doesn't requre grinding ovlf spider gears. You can see full installation video right here. kzbin.info/www/bejne/mH2ohJmelqiFhac
@doomslayer50442 жыл бұрын
@@RacingDiffs thank you so much for the fast answer, cant wait to order a set
@7H3_23R02 жыл бұрын
Could you please tell me what is your shoes's brand?
@RacingDiffs2 жыл бұрын
Skechers 😊
@coreytelfer45662 жыл бұрын
What is the torque wrench used in this video?
@RacingDiffs2 жыл бұрын
We got good old wrench, which we calibrated and it works perfect. But don't know the make. I'm sure similars are to be found on Ebay.
@eXoguti094 Жыл бұрын
God the music is so loud... You guys don't need any music in these videos, we're just interested in the straight-up talking
@1Heyfred7 ай бұрын
Good video, but the music is annoying and makes it hard to follow.
@RacingDiffs6 ай бұрын
Appreciate the feedback. 👍🏻
@johnyxxx2 жыл бұрын
Love your video's, but please stop using that background music when he is talking, it's very annoying. Thanks!