RC Flying: How to install a UBEC to power only the retracts.

  Рет қаралды 7,857

jbfordfocus

jbfordfocus

Күн бұрын

Пікірлер: 16
@etiennehogue8780
@etiennehogue8780 Жыл бұрын
Finally A good explanation, it seems no else can provide these instructions clearly.
@danb.4571
@danb.4571 2 жыл бұрын
Outstanding. The factory instructions want all the UBEC power transferred to the receiver while eliminating the SBEC, which I did not wish to do. This cleared up all my questions. Thanks for a nice, concise explanation.
@heydonray
@heydonray 4 ай бұрын
Well enough and thanks for the supreme effort that went into this vid. HOWEVER, I am at a loss for a reason to only supply the retracts rather than the entire Rx and ALL servos. No more effort for more safety.
@jbfordfocus
@jbfordfocus 4 ай бұрын
The retract motors draw a lot of power for a few seconds that reduces the available power to your other more critical servos. ie: When coming into land, you activate flap servos + your retracts, plus you are using all the control surface servos, so keep the retracts out of this power loop is preferrable. Also, servos do have a tendency to burnout and short pulling a huge amp draw. To have all this isolated through the UBEC keeps the critical services still operating. But to answer your questions, you could put both flaps and the retracts through a UBEC.
@flashthunder829
@flashthunder829 Жыл бұрын
Outstanding explanation
@michaelvidal9234
@michaelvidal9234 Жыл бұрын
Excellent, this will be used on my Rans S-20
@dDevilsrReject
@dDevilsrReject 2 жыл бұрын
Thanks, some good info in this vid.
@tulushadi
@tulushadi 3 жыл бұрын
i have been looking for this.. thanks for the video
@franciscoe.9989
@franciscoe.9989 3 жыл бұрын
***** Respect *** Great Presentation
@Lawzy
@Lawzy 5 ай бұрын
Thanks for creating this overview. Can you or any of your viewers please tell me whether the common ground (UBEC, receiver, servo) is still needed if the receiver is being powered by the UBEC? Or can the receiver/servo common wire be removed? Thanks.
@leksychannel7332
@leksychannel7332 Жыл бұрын
Great 👍👍 , btw may I ask, this is a dual output, can the two outputs be different from each other, for example 1 for the 8.4v servo, the other 5v for the lights
@leksychannel7332
@leksychannel7332 Жыл бұрын
😁Can you make a follow-up video about settings with two different voltages, then what must be considered so that there are no installation errors 😊
@powerofdreamx
@powerofdreamx Жыл бұрын
Thank you
@allanhvidt-nielsen7777
@allanhvidt-nielsen7777 11 ай бұрын
Good explanation. just one question, as the servo is already powered by the Ubec, would it not work with only the signal wire going back to the reciever?? Or do you really need the negative as well?
@prov418
@prov418 6 ай бұрын
I have the same question, I think you may be right. I don't know enough, but it seems like this method is creating ground loops which I assume are best to avoid.
@whiteboy8236
@whiteboy8236 8 ай бұрын
thank you
When to Use a Battery Eliminator Circuit (BEC)
18:13
RC Video Reviews
Рет қаралды 17 М.
RC CRAWLER TALK:  BEC'S FOR RC CRAWLERS
12:49
SCALE RC CUSTOMZ
Рет қаралды 4,3 М.
MAGIC TIME ​⁠@Whoispelagheya
00:28
MasomkaMagic
Рет қаралды 17 МЛН
ROSÉ & Bruno Mars - APT. (Official Music Video)
02:54
ROSÉ
Рет қаралды 204 МЛН
😜 #aminkavitaminka #aminokka #аминкавитаминка
00:14
Аминка Витаминка
Рет қаралды 2,3 МЛН
啊?就这么水灵灵的穿上了?
00:18
一航1
Рет қаралды 101 МЛН
MORE POWER! Fitting a UBEC to my RC
11:29
RCKicks
Рет қаралды 5 М.
What is a BEC and why do you need it?
5:31
HolmesHobbies
Рет қаралды 49 М.
What is a BEC and what do they do in the RC hobby?
9:10
RCJuice
Рет қаралды 73 М.
How I choose my servos for RC planes || F3A Basics
7:07
Rombaut RC
Рет қаралды 7 М.
Tes Remot Flysky FS i6 Pakai Servo
7:54
Tuas RC
Рет қаралды 26 М.
Como conectar un BEC externo para alimentar nuestro RC.
10:23
HerederO Dj
Рет қаралды 6 М.
MAGIC TIME ​⁠@Whoispelagheya
00:28
MasomkaMagic
Рет қаралды 17 МЛН