RC HELICOPTER CRASH !!! SCALE RC BELL-206 JETRANGER / Modellflieger Show Gatow 2014 *1080p50fpsHD*

[@KevinTalbotTV]

Am the only one that finds RC helicopter crash videos funny? Good work cameraman!

[@johneells7415]

Why funny ?

[@MStreppelhoff]

Helifliegen ist einfach das geilste Hobby ! Königsklasse :)

[@onuralibatmaz5597]

doesn't matter how big it is, it is always heartbreaking.....

[@bmpowellicio]

The tail rotor stopped suddenly but the blades are still attached, so it might just be a main blade striking the tail, something that often happens in sharp turns in scale helicopters. It's embarrassing for the flier, but it can be fixed mechanically in a couple of hours, but the GRP fuselage needs repairs and then lots of filling, sanding and painting to get back to its original shine. Sadly, this happens more in shows than elsewhere because of the extra stress of operation to a timetable and in unfamiliar surroundings, but most people who fly these things are relaxed about crashes and the repairs needed. I know I am!! If you don't fly you don't crash, but we like to fly.

[@dominicfeliciano9462]

4:56 Blades is in trouble! 4:57 Blades!

[@MrMHelis]

Uups. Hab ich gar nicht mitbekommen. Ich war am Samstag auch da. Und nächstes Jahr bin ich auch wieder da. Wirklich ein tolles Event.

[@rc-media-world]

ja ich bin 2015 auch wieder da wenn das wetter passt.... tja man muss eben permanent auf alles die kamera drauf halten.... grüsse bunterfisch

[@hinnerkemme4715]

Ich bin Hobby Modellbauer , und mitten im Flug hat meine U36 Feuer gefangen , die blieb aber 10 in der Luft , sah richtig nice aus. Hatte sich gelohnt

[@mr.blairs4501]

ohhh man echt schade um das Teil ;=) tut mir echt leid

[@ng21644605]

Great copter pilot - Must have been quite the bummer for him.

[@ng21644605]

***** My guess is, You've got way more money than I do,

[@kiter147]

I'll stick to my indoor heli thank you very much

[@selivanyro]

eh-he-he your afraid to fly)

[@positivemasculinity42]

A pilot whos scared of the outdoors. Like a hacker whos scared of computers

[@8672Danny]

morrgan haack I'll stick with my Hex-copter xD

[@spidernad1]

If you pause at 4:54 you can see the tail rotor drive snap off. And then, Scheisse! Even I Know What That Means. lol Sorry for the loss.

[@tobyjarett]

how much does one like this run 900.00 us dollars or more?

[@aed040]

toby jarett More than 900usd. the stock pod and boom heli with that size already costs more than 900usd.

[@InTheDogHouse3DPrinting]

Scheisse means Shit! A setup like that will cost close to $6500.00. I had looked into getting one till i saw the price.

[@tobyjarett]

oh wow i had no idea that they were that much. what an expensive flight.

[@isyourshitfixed]

***** all of you are incorrect 1500 rtf rcaerodyne.com fuselage 500 hobbyking.com 600 size kit 150-200 receiver radio cheap 2.4ghz 50$ some where around 100-150 for ESC brush less motor lipos , most expensive part is getting established etc chargers ,learning (crashing alot) get a 450 size heli 350$ ready to fly visit www.xheli.com

[@1205juergen]

Sehr schöner Flug , aber leider kein gutes Ende ....

[@mikej9014]

This was filmed on my birthday :O !!

[@STRIDER_503]

What a shame, that model is beautiful.

[@luciuskun4932]

i wonder what struck the helicopter??? big shame

[@STRIDER_503]

Tail rotor came loose and flew off, struck the main rotor then it crashed.

[@luciuskun4932]

what a pitty.tanks for telling me

[@casperaudi7476]

Came in to have Fun with his toy helicopter left disappointed It will be better next time don't give up..

[@Mrbfgray]

Pretty good landing from what I see around here.

[@heinzklossok701]

"ECHT SUPER" Die Angst fliegt immer mit!

[@ElectronNinja]

Mains whacked off the stab and tail blades. I'm guessing either too little clearance, squishy dampers in the head, or both.

Commodore8888 great stack though 👍🏻🍺

[@RCModelPlane]

tolles video

[@floex831]

4:53 schizer, I don't wanna play anymore.

[@ost6018]

Ohje. Der arme Heli. Sehr schön geflogen. Sah so aus als ob der Heckrotor blockierte und was weggeflogen ist. Aber auf den Handy ist es schwer zu erkennen. Hoffe, der Heli kann wieder aufgebaut werden.

[@svenwollenberg8953]

Ost601 ...der Heli wurde aber auch hart rangekommen ... wahrscheinlich ist die Pleuelstange des Heckrotors gebrochen oder eins der Heckrotor Blätter ist gebrochen

[@KS71-l7y]

This pilot realy flys the helicopter and does some aggresive manouvers too. Pitty he lost the heli in that way, but at least he was realy flying and not just hovering an inch from the ground.

[@tonydilluvio6274]

Sorry for your loss but that was the most scale-like flying of a model helicopter that I have ever seen...

[@tonytrimboli4517]

Check out ( MD530 does backflip ) No Idle up !

[@dirtsammich4377]

Yea, great scale flying, I liked watching the progression as he warmed-up. Sorry for your loss man.

[@FrustratedNameSearch]

I hate equipment failures like that. But, I've been there. With a Bell 222 that took me 3 years to build. I quit after that.

[@Thrashaero]

FrustratedNameSearch which is why you go flybarless micro, they handle the punishments, especially over tall prairie grass it's like nothing happens. unless you are stupid rich for scale crashes, it is pointless.

[@kc5hgv]

Ouch looks like a bird strike @ 4:54. I saw a bunch flying around during the video.

[@DestructoGuy17]

At 0:45 it looks like a real helicopter flying through the sky!

[@Casemaster3000]

DestructoGuy17 yeah all perspective isn't it, good way to save money on filming movies :P

[@Robert111]

+DestructoGuy17 It is actually a REAL helicopter, but a small one.

[@WasteTime4Passwords]

+Robert111 Again, we have that "Jimmy Stewart and the German Areo-Engineer conversation," from that movie where they built the little plane out of a wrecked bigger plane.

[@yesicamoctezoma9097]

y

[@siddharthiyer1120]

From what I can see, the tail rotor screw got loose, causing the blade to tip and strike the Vertical stabilizer intern cutting of all circular motion and causing the heli to go into a tail spin...

[@Yefatbastard]

Yes the problem started in the tail assembly.. It was NOT a main rotor, tail or boom strike.. The main rotors are still in good shape all the way to the ground.. I suggest watching it at .25 speed..

[@siddharthiyer1120]

yeah, I did, when said the blade tipping, I meant the tail rotor tipping

[@14Mentalist]

In other words the screw came of hit the blades and caused it to fall.

[@mickjagger6168]

Siddharth Iyer Are you a 100% sure it looked & sounded like while in the turn the torque just snapped the tail wing ?? I had that happen to one of my old bell 1/4 scales.. JUST PUTTIN THAT OUT THERE. EATHER WAY IT SUCKS !!!!

[@ivanchico7]

mick jagger yeah i think you're right

[@markgamble8377]

hope it was salvagable. heard the snap.nice show till then.musta been near the end.

[@jimmyd4092]

Man that sucks , nice heli and good flying till the tail came off, I've had my share of servos dying in mid air ,loose bolts , bad luck and bad flying sometimes, just part of the hobby

[@schreibhecht]

Ich würde gern mal sehen wenn der Motor gestartet wird. Mich interessiert wann der Rotor sich dreht. Ich sehe immer nur Filmchen von Turbinen aber vom 2 Takter hab ich den Start noch nie gesehen.

[@russellparr9252]

Looks like the vertical fin either came loose or the stress of the turn caused it to lean into the tail rotor and... well, catastrophe. Too bad, that was a beautiful bird. I'm sure he'll get it repaired and up flying again.

[@JamesLewis-mp9zn]

Last month almost had a mishap. Just changed to a fresh battery for my Hughes 300C and was about to lift off when I heard a ZZZZ sound. Quickly drop the collective and shut down. Did a quick visual and didn't see anything out of place. Tried again same noise and decided to call it a day. When I got home took the canopy off to do a through inspection. What I found cause me to say "O Shit". I lost the tiny screw to my pinion gear to the motor shaft that caused to freely turn. That's the one thing I didn't lock tight. From then on any time I'll take one my helicopters out (have a small fortune tie up in scale birds), I'll double check everything.

[@ChrissiRC]

Au man, der Arme! Was ein Kack! Hoffe der Heli wird wieder!!! Der hatte doch vorher schon Probleme bei der Landung! War wohl nicht sein Tag.

[@OznaczenieSeryjneN]

What the heck caused it to crash?

[@theslicelifewdominos]

Sorry man! That looks $$$. Did you fix it? Anyways, your flying was very good! Good job!

[@Drrck11]

What caused it to crash? It appeared to be perfectly fine.

[@Beamshipcaptain]

Tail rotor itself came loose, a screw wasn't locktied or something, and the tail rotor assembly, pitch-change plate and all, came loose and whacked the vertical stabilizer fin. Might be able to autorotate, but he was too low for that setup.

[@marcwage]

Wunderbar!!!!!!!

[@joeyindie7593]

the governor rotor and tail-up wing are broke and malfungtion thats why the helicopter lost its stabbilize and rotating then crash the ground. note: dont force your rc helicopter

[@bitemykrank1970]

What actually happened ? Was it component failure, structural failure or boom flutter ? All i can see is the tail rotor goes, and the rear of the boom is chopped, once there is no correction , the uncontrollable spin begins, luckily it didn't fall too far. I hope the damage was minimal, it's such a nice bird, and was being flown beautifully until it went pear-shaped. You have my sympathy. I might be able to work out what happened if i could read German.

[@bartsshorts]

i am truly thankful for your loss

[@the10thleper]

What the ..... dang, looked as if it hit something the way it broke buckled and crashed so quick. Did a shaft break? That was a significant malfunction. Nice model.

[@haroonali9089]

crash is at 4:56

[@abdulhakeem7225]

thanks

[@harrygrabow1545]

Hier hat sich die Verklebung vom Heckrotorbefestigungsspant gelöst wodurch der komplette Heckrotor herrausgeflogen ist

[@jjj5647]

slight mechanical hitch ... I don't speak German but understood shizer 5.03. If I watch more of his videos I should be fluent in no time.

[@brab199]

I'm confused, what made the tail calasp like that? Was it moving to fast when it was making the turn & just put a lot of stress on the tail? I went to read the description & had no clue what it said.

[@geraldevans4624]

well must say that was great to whach

[@efgtest]

1 tiny lose rear rotor screw $0.02, Mamage because of that tiny screw $2500.

[@TransferAir]

Schönes Modell, gut geflogen aber der Kommentator dann: ... "Das war ja jetzt natürlich ... SCHEIßE!" Sorry aber 🤣😂 ... zu lustig und treffend kommentiert echt!!! Hahahaha!!! ✌🏼

[@cammarota7487]

Watch your video in slow motion, with an equipment of great quality, exitem foreign objects at high speed while flying your helicopter. Sorry I'm using Google translator, because I live in Brazil and do not speak English. hugs

[@menard2835]

The birds were chasing it lol . Took out a blade 💸💸💸

[@RCGuy-dk9uo]

That's a shame it was a very nice helicopter and the flying was great I believe that its gyro falied causing the whole thing to snap into itself and crash it happened to me to I am sorry for your loss it was a very nice helicopter.

[@XyntiaOna]

ile udzigu ma ten sprzecik. i jaka maksymalan wyskosc.

[@jameslarson9066]

If you slow it down you can see the Humming Bird fly into the tail rotor and that's all she wrote...

[@ipadize]

könnte es sein, dass die vorherige Landung etwas angeknackst hat?

[@rc-media-world]

naja ist im nachhinein schwer zu sagen, könnte aber sein....

[@gustav_a.mozumder2011]

I am confused, how did it break in mid flight?

[@jeffmullinix7916]

That looked vary real when it came a part in the air .

[@WilsonLafaurie]

Mr. Murphy made an appearance, there was miles of green grass versus a few feet of concrete. Guess where it landed? GREAT heli, alot of work and money, its obvious.

[@AdammP]

looked like the tail rotor prop shaft broke mid flight, couldn't see too clearly but looked like something flew out of the tail and the rear propeller stopped working. comes with the hobby unfortunately!

[@chrismeade4613]

The real "Angry Bird" is holding the remote control !!!

[@taytaytay871]

How is it that all these kind of videos doesn't include DCS ...

[@cammarota7487]

Watch your video in slow motion, there are objects flying at high speed during the flight of your helicopter.

[@heliextrimone]

NTSB-Style :P

[@001GenLee]

Which is why I would buy a beginner helicopter over the more expensive / professional copters. I'm still learning, even though I haven't flown one in 2 years now. I had one of those Air Hogs Pocket Copters that you fly indoors, they're pretty cool but the charge doesn't last no time.

[@Phericzehn2]

i saw the same! more than two, they just flying around!

[@geraldevans4624]

well i have a hellicoptor my self its a rapptor 30 thunder so iam asking what do i do when i switch it on can you tell me please thank you so much.GERALD EVANS.

[@vedasticks]

Go to a model flying club. I just looked at what the raptor 30 thunder is and without any experience this thing is lethal.

[@geraldevans4624]

well i bet this hellicoptor cost a bit about 500 to 700 well now it will oh dear.

[@lucid523]

you know how much money that would cost you to fix all that probably as much as a new car or probably more

[@sophiaharris9916]

It was to much pressure on the tail rudder causing it to bend an lose control

[@ethanevans9268]

Or the tail rotor screw came loose ?

[@themanthemyththelegend1392]

Could have been saved if the pilot knew all orientations...

[@muhammadikhsanfirdaus9189]

well but I fell sad 😩,just think what happen if that happen to me

[@muhammadikhsanfirdaus9189]

waw are you me?

[@tanseiyang3163]

what broke up in the air?

[@SOLDOZER]

Skip to 4:45 to watch carnage

[@dirtsammich4377]

Was that anything like the gunship you flew in 'nam? I know it was million dollar equipment but its gotta be better than parking cars..

[@jeffmullinix7916]

I was scipping frames and the tail trans looked like it came loose causing the tail blades striking the vertical fin .

[@jeffmullinix7916]

I skipped threw the frams again and the tail gear box did indeed came loose that caused the tail blades to strike the vertical fin . This happed at 4:54 in the flight .

[@pramodghadage5355]

Rip💐💐💐💐💐

[@superchargedM90]

Just go to at 4:53

[@LtdBoomer]

Das wäre kein Hobby für mich.Tausende investieren um Sie in den Sand zu setzen in ein paar Minuten. Dann doch lieber Standmodelle für die Vitrine im Wohnzimmer.

[@MisterLEM0NS]

Ladies and gentlemen, the difference in flight between having a tail rotor and not having one.

[@rachelpriddy8088]

when will it crash

[@kristinemariepinote1519]

The most painful and slowest death on a heli is the tale rotor being explode

[@PikabooBaap]

What about its price

[@ethanevans9268]

I think it may have been a loose pin drive reel in the starboard side of the main engine

[@Ride-Fly]

😂

[@TheMrSimi]

Sieht aus als wenn hinten der ganze Heckriemen rausgeschossen ist weil da ist die Karo aufgeschossen

[@jerryfox2960]

What was it though? couldnt see any bird it just exploded

[@klaus3968]

ein Jammer, so ein schönes Modell :-(

[@marcelolemes342]

Que pena heim. Parece que foi atingido por um pássaro. Estava indo tão bem

[@Ward00]

NOT hit by a bird.

[@digitalbroadcaster]

Vertical stabiliser detached and went into the tail rotor. Then planet Earth decided to have a go and crash into it too.

[@bushpilot-bm3kf]

Basic main blade tail strike, nothing special. Scale bird had long main blades and a very tall tail. Level flight o.k. but hard turn bank and tail strike.

[@XYDogAustria]

Und 1000 Euro Futsch oder..ist da an Vogel rein geflogen oder sowas ??

[@xpadakel4795]

4:50

[@berg6945]

wat did it hit ?????????

[@Saburai868]

the ground

[@berg6945]

In the air u idiot wat made it hit the ground smart one

[@lotus9937]

The main rotors stretched and cut the tail rotor.

[@berg6945]

Oh thank u

[@sarah20025]

Voiletest Man

[@sniperm8942]

It's look real from an angle

[@klatovakhendrix4721]

I had a smaller helicopter than that. When I was flying with it, the helicopter was so far from me and there wasnt a signal. Suddenly fell to the earth about from 40m.. its a tought

[@SethHamburg]

Die rote Leuchte ging immerhin noch.

[@QuadrocopterTipps]

Kennt ihr gnutz ???

[@jeffmullinix7916]

It's a Kavan Jet Ranger .

[@Giovanniram22]

And now what I will tell to my wife to buy a new one?

[@neleabels]

Wie schrecklich, das schöne Modell... :(

[@halleffect1]

that thing came down like a rock.

[@amitsunkur8127]

A lost of tail rotor i noticed???

[@MsOkcokc]

слава богу хоть тихо стало, все довольны

[@TwazkemUSAbi]

OMG WAS EVERYONE OK?

[@MAPLERO4D20]

Did it strike a bird or something?

[@GraemeMurphy]

One of the four main rotor blades failed.

[@InTheDogHouse3DPrinting]

GraemeMurphy It wasn't a main blade that failed, it was the tail rotor.

[@Nine.ix.9]

RakinBill yup... it's the tail rotor that flexed and hits the tail... however that's a big ouch to the owner's pocket... :D

[@wouteranthierens]

I think the bearings of the tail-rotor got jammed. Probably the tail-rotor was driven by a belt. The belt ripped the end section of the tail, and resulted in a loss of tail rotor control. He had no time to cut off his engine for an auto rotation.

[@susanthasusa8307]

ZulkarNINE Zamhuri

[@asw850]

You got exactly what you paid for!!