Rebuild Carburetor - Johnson Evinrude OMC Outboard

  Рет қаралды 40,662

thisoldoutboard

thisoldoutboard

Күн бұрын

Пікірлер: 66
@Ayerlooms
@Ayerlooms 2 жыл бұрын
Thanks for taking the time to make these videos. They are priceless. I’ve been working on motors my whole life and I always pick something up free m watching someone else. I haven’t been inside a motor for a few years and I just got a mint FD-11K and I have been monkeying with the carb and forgot all about the damn float being level to the body lmao. Who says ya can’t teach an old dog new old tricks. Lolol. Dammmmmmit man. I’ve had that pig apart five times like I gotta have a piece of trash in a Venturi lol. Nope damn float wasn’t set. Set that sucker and she sat dead flat still at an idle. Had the screws set perfect. Lol. She is just the nicest motor one could find. I bet it doesn’t have ten hours in it. I ripped the whole thing apart and every single screw came right out not a drop of corrosion on any screw like it was built last week. You don’t get em like this one often. I was told there were only 22000 made with the K after the 11 and that that was to signify that it was a 571/2. Something is different in the build than the first half of the year. Any idea what’s different ?? I can’t see anything that stands out from my other. ??!!!! Tia for any help.
@robertdurbin1632
@robertdurbin1632 5 жыл бұрын
Great video. Helps with where to get started. Thanks for taking the time to make this video.
@johnnybk7436
@johnnybk7436 3 жыл бұрын
Great video! Thanks for your help.
@bodomchildrenof
@bodomchildrenof 6 жыл бұрын
You're a great tutor. I owe you one for the knowledge you pass on. Now, I can maintain my 10hp Golden Jubilee :-) Thank you!!
@dennisfalan1623
@dennisfalan1623 5 жыл бұрын
He doesn't know what he is doing almost all the info in this video is WRONG! even the initial adjustments are way off if you follow his instruction the motor will not run anywhere near as intended Buy an OMC Evinrude Johnson manual I recommend Seloc 1956-1970 Evinrude Johnson tune up and repair 1.5 to 40 hp
@gorp27
@gorp27 5 жыл бұрын
Pretty good video. One thing I would recommend is using those Stanley screw drivers as chisels and such and to invest in a good set of hollow ground screw drivers, you won't be disappointed in the investment.
@Mark-wx1ho
@Mark-wx1ho 6 жыл бұрын
Brilliant video once again. Same carb as my 1960 model. Also used your link for the carb kit which also ships to the UK. You are a real help my friend. Thanks again.
@dennisfalan1623
@dennisfalan1623 5 жыл бұрын
to bad all the info is wrong brilliant video LMAO!!!
@hamshter
@hamshter 7 жыл бұрын
great vid. That's really helped me work out where the bits go on my Johnson carb. Cheers !!
@detroitredneckdetroitredne6674
@detroitredneckdetroitredne6674 7 жыл бұрын
Great job thank you for your knowledge and expertise I will learn a lot from this
@jandrschreppel2752
@jandrschreppel2752 4 жыл бұрын
I just aquired 5 different old boat motors. The first one I am tackling is a '53 Johnson 10HP QD-14. I dont see that model year under 10HP carb kits in your links. Where would I find the right kit for this particular motor?
@thisoldoutboard
@thisoldoutboard 4 жыл бұрын
They are all the same. Sierra 18-7043
@jesseparrott6328
@jesseparrott6328 3 жыл бұрын
Could I use this logic to determine other parts too. Say for ie an impeller kit? I've found the 53 is hard to part together, myself.
@wallerking2966
@wallerking2966 Жыл бұрын
I cant find the link for the rebuild kit. I have a 57' 30 hp evenrude big twin 25924, i cant find hardly anything for this old motor and it is very dear to me. Does anyone know what kit I need?
@CarlosRodriguez-xm3qv
@CarlosRodriguez-xm3qv 4 жыл бұрын
hi i have a 1959 gale buccaneers outboard do you have any video on those or how i can use for reference
@CarlosRodriguez-xm3qv
@CarlosRodriguez-xm3qv 4 жыл бұрын
25 hp
@thisoldoutboard
@thisoldoutboard 4 жыл бұрын
I do not, I hope to make some soon
@highwatercircutrider
@highwatercircutrider 2 жыл бұрын
Isn’t the bottom jet in the bowl the high speed jet and the upper jet for low speed (what am I missing here?).
@NotSomebody63
@NotSomebody63 4 жыл бұрын
Can I use B12 parts cleaner instead of the acetone you used?
@thisoldoutboard
@thisoldoutboard 4 жыл бұрын
Yes
@kennethhamby7665
@kennethhamby7665 2 жыл бұрын
Is there any differences in dimensions on the high and low speed adjustment pins?
@daleburnett8431
@daleburnett8431 2 жыл бұрын
Yes the upper which is low speed comes to a point more like a needle vs the lower which is more of a blunt end once you have both out or in hand and they both have the same threads so don't mix em up
@kennethhamby7665
@kennethhamby7665 2 жыл бұрын
@@daleburnett8431 the reason for asking is, the low speed pin was lost before I bought the engine, and was trying to get a figure on having one machined out
@nateward6483
@nateward6483 4 жыл бұрын
Do you have a link for a fuel pump kit for a 1971 Johnson 20 horse 20R71s
@thisoldoutboard
@thisoldoutboard 4 жыл бұрын
thisoldoutboard.com/johnson-evinrude-carburetor-rebuild-kits/
@Dmonieluv
@Dmonieluv 7 жыл бұрын
Excellent tutorial, thanks maan!
@thisoldoutboard
@thisoldoutboard 7 жыл бұрын
Glad it helped
@dennisfalan1623
@dennisfalan1623 5 жыл бұрын
Lol so wrong
@mulespur4806
@mulespur4806 5 жыл бұрын
I've got 59 35hp super seahorse and can't find any carburator kit all together I've seen one piece at a time but I need a complete kit
@thisoldoutboard
@thisoldoutboard 5 жыл бұрын
amzn.to/2MJ4dXf
@mulespur4806
@mulespur4806 5 жыл бұрын
@@thisoldoutboard thanks a million
@JoseGarcia-pd5bo
@JoseGarcia-pd5bo 7 жыл бұрын
Thank you you for the info!
@tayfs414
@tayfs414 7 жыл бұрын
Thanks for the video!
@mulespur4806
@mulespur4806 5 жыл бұрын
I was wondering if you know what kind of sealer to use for a cork float that can stand up to ethanol gas the shellac I was using don't work
@gerardjones7881
@gerardjones7881 4 жыл бұрын
throw it away and get a new plastic float, it will never give any trouble.
@alexchorny1
@alexchorny1 3 жыл бұрын
How to adjust low and high speed needles?
@thisoldoutboard
@thisoldoutboard 3 жыл бұрын
bit.ly/2faZY66
@travissnyder5123
@travissnyder5123 5 жыл бұрын
I have a QD-23 motor can you tell me what it is
@thisoldoutboard
@thisoldoutboard 5 жыл бұрын
It’s a 1962 Johnson 10 Hp
@ZackofAllTradesct
@ZackofAllTradesct 7 жыл бұрын
Very helpful. Thanks.
@Reidball100
@Reidball100 6 жыл бұрын
The carb kit referenced comes with more pieces than you need, correct? Looks like a lot of extra washers, seals, gaskets depending on the exact year. Is that correct? I have a 1955 QD-16 10 HP, and just bought this kit from Amazon: www.amazon.com/gp/product/B07F73M7MS/ref=ppx_yo_dt_b_asin_title_o01__o00_s01?ie=UTF8&psc=1. Looks like a lot I don't need given the replacement parts you noted here. Thanks for any feedback you can provide!
@thisoldoutboard
@thisoldoutboard 6 жыл бұрын
Yes the kits can have extra parts. The kits are for a range of years and models. They are cheaper to sell that way, that’s why.
@nobodyspecialdotorgrichard5971
@nobodyspecialdotorgrichard5971 6 жыл бұрын
Any idea what I am referring to or how to adjust it?
@DundoMarinko
@DundoMarinko 7 жыл бұрын
Freeze -off ---by CRC is best for rust or acceton with trasmition fluid 10% let sit and do it work avesom lesson you give keep it up
@nobodyspecialdotorgrichard5971
@nobodyspecialdotorgrichard5971 6 жыл бұрын
Very helpful video! When you screwed in the long needle(the low idle adjustment) you didn't show the little thing inside there that the needle actually screws into(it doesnt just screw into the body of the carb!) On my 1958 evinrude18hp, it comes out when I pull the needle out! It is just a cylindrical tube with threads inside it that seats in there and the needle screws into. I shove it back in and then screw the brass piece in and then I screw the needle in but, I am completely confused by these three parts and how far to screw it into the piece. mine wont stay running so, I was hoping to see what you did with this piece.
@thisoldoutboard
@thisoldoutboard 6 жыл бұрын
On this parts diagram, which part (number) are you referring to? www.marineengine.com/parts/johnson-evinrude-parts.php?year=1958&hp=18&model=FD-12&manufacturer=Johnson&section=Carburetor+Group
@snowhenson
@snowhenson 6 жыл бұрын
We have a Johnson FD-18 E Serial no.J 2429434 Sea Horse what carburetor kit will work on it?
@thisoldoutboard
@thisoldoutboard 6 жыл бұрын
18-7043 on eBay ebay.to/2t8a6Uc or Amazon amzn.to/2Moiac9
@chuckcecconi4571
@chuckcecconi4571 4 жыл бұрын
Is this the same for a 1970 Evinrude 18 hp fastwin?
@back40adventures74
@back40adventures74 8 жыл бұрын
Would be nice to see something for the 9.5 motors as well!
@thisoldoutboard
@thisoldoutboard 8 жыл бұрын
Back40 Adventures I've owned several but I don't have one at the moment. If I get another I definitely will make a video.
@thisoldoutboard
@thisoldoutboard 7 жыл бұрын
Hey I added a couple of videos to my channel where I rebuilt a 9.5 hp carburetor.
@nazaer1
@nazaer1 7 жыл бұрын
do you have a video on how to tune the carb
@thisoldoutboard
@thisoldoutboard 7 жыл бұрын
I don't have a video but here is a link with a detailed description of the initial settings. bit.ly/2faZY66 A full tune up needs to be done on the water while the engine is running.
@nateward6483
@nateward6483 4 жыл бұрын
Hey man where are you from? I need my motor basically completely rebuilt it’s a 1971 Johnson 20 horse this thing is a shit show was wondering if you would be willing to basically rebuild it for me thanks
@stevenreed9268
@stevenreed9268 4 жыл бұрын
That was almost painful!
@calebnewsam8843
@calebnewsam8843 4 жыл бұрын
Uhh, you did not install the high or low speed packing washers correctly. Please follow the repair manual and illustrated parts breakdown.
@outboardfixer
@outboardfixer 4 жыл бұрын
Top needle is low speed not high.
@nodnottap
@nodnottap 7 жыл бұрын
does anybody know what the carb settings are for an Evinrude model 4266
@nodnottap
@nodnottap 7 жыл бұрын
how do you start 1940 1.1 hp evinrude
@gerardjones7881
@gerardjones7881 3 жыл бұрын
forgot all the packing washers around the needle. Thats gonna leak like a strainer. This is not useful.
@tuckerlaws2371
@tuckerlaws2371 4 жыл бұрын
Muffler you mean in take
@thisoldoutboard
@thisoldoutboard 4 жыл бұрын
Silencer was the term I should have used See Part Here ---> www.marineengine.com/parts/johnson-evinrude-parts.php?year=1959&hp=10&model=QD-20&manufacturer=Johnson&section=Carburetor+Group
@dennisfalan1623
@dennisfalan1623 5 жыл бұрын
You don't know what you're doing That is not how you adjust the float and you didn't even use the packing washers. The jet needles are going to need adjusted all the time and your initial jet needle adjustments are wrong also The low speed should be backed out 1 1/2 turns then adjusted while at the slowest idle you can get and keep running the high speed initial adjustment is 3/4 turn out read the manual before you do a video it's not just take a guess at it and make a video
@thisoldoutboard
@thisoldoutboard 5 жыл бұрын
Thanks for the feedback
@highwatercircutrider
@highwatercircutrider 2 жыл бұрын
The identification of the high and low speed jets was mixed up
25 Hp Johnson Evinrude Carburetor Rebuild
11:24
thisoldoutboard
Рет қаралды 134 М.
How to Clean Rebuild Carburetor 1957 7.5 HP Johnson 1952 thru 1967 Johnson & Evinrude 3 HP to 18 HP
26:58
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН
coco在求救? #小丑 #天使 #shorts
00:29
好人小丑
Рет қаралды 120 МЛН
Fuel Conversion to Single Line 1957 5.5 HP Johnson T-Mike Tricks #outboards
18:00
T-Mikes Vintage Outboards Restoration
Рет қаралды 1,1 М.
Dialing In a Carburetor After a Rebuild
8:01
Old JohnnyRude
Рет қаралды 7 М.
1954 - 1959 JOHNSON / EVINRUDE 5.5, 7.5 AND 10HP REVIEW
11:35
Boat Motors
Рет қаралды 1,7 М.
1955 Johnson 5.5 Outboard carburetor cleaning
13:48
Crazy Bill's Garage
Рет қаралды 477
1958 Johnson  Evinrude 10 HP Carburetor Overhaul
26:25
Brandon's Garage
Рет қаралды 16 М.
HOW TO CLEAN AND REBUILD 6HP JOHNSON / EVINRUDE CARBURETOR
13:36
Boat Motors
Рет қаралды 10 М.
1958 Johnson 10 HP - Adding Fuel Pump
12:08
Brandon's Garage
Рет қаралды 24 М.
黑天使被操控了#short #angel #clown
00:40
Super Beauty team
Рет қаралды 61 МЛН