Rebuilding turbo ford 6.0l powerstroke

[@donaldkeezer9413]

??? What about the electrical part. Oil plunger. How does that come apart. Great video.

[@s33therfan]

Seems like I lost that in the editing , but I remember taking it out with a magnet and cleaning it up some. Thanks for watching.

[@Matt_Huffman]

Thanks man, wanted to see what I was getting myself into before I started. Very helpful!

[@s33therfan]

Thank you for the feedback. It is not too bad once the turbo is off the vehicle. This turbo had alot of slack in it and this kit really did the job. You have probably heard about the upgraded drain tubes for the turbo , you might slap one of those on there if it has not been upgraded yet. Best of luck on yours and thank you for watching

[@Matt_Huffman]

s33therfan thanks for the added feedback, I didn’t know about the drain upgrade so I will be adding that to the list. Also, if you don’t mind me asking, why did you remove this turbo again after you already rebuilt it a month prior? Or did I miss that part of the video?

[@s33therfan]

I did not do a rebuild the first time I cracked it open . I just went in and cleaned all the rust and vanes , and put some antiseize. I had actually got another turbo and was trying to decide which one was the best to rebuild. The kit worked out perfect though. Great question and thanks again.

[@backwoods6334]

Awesome video just got your self another subscriber just bought a 6.0 powerstroke got an extra turbo with it that needs rebuilt so this video will help me alot thanks

[@s33therfan]

Thank you very much for the great feedback , and thanks for watching

[@felipeamaya9831]

Great video I'm about to rebuild 2006 f250 turbo charger ,thanks broth

[@brandond3010]

Be nice to see some detail on "how" you got the O ring on at the 18' mark. Every difficult thing in this - video stops while it's done then just starts again like it was nothing. I have the same kit and that O ring just won't seat. Used the bolts to hold it while stretching it around but the diameter is so thick it won't bite into the groove so still just pops off once it's not held

[@ericklago9185]

Great video !! you took your time to explain everything thank you

[@s33therfan]

Thank you for the feedback , I hope it helps you out on your project . It's good to make a in depth video that can help someone make sense of it and know what to expect. Thank you for watching

[@hagermancakemeister9204]

Great video man!! Thanks for keeping it up!!

[@s33therfan]

Thank you for the great feedback I appreciate it and thank you for watching.

[@tonybersaglieri9953]

Just curious, how has that rebuild kit help up? $30 for a rebuild kit seems like too good of a deal to last more than a year

[@Cherokee93]

I might put one of these on ford 4.9 bc I can get it for free but it needs bearing and seals. how would I lock the vgt? I would use an external wastegate

[@ldtexas1648]

Yeppers! Helped me out too! Thank you!👍

[@s33therfan]

Thank you for watching

[@bobsdogtag]

another fantastic video !!!!!!!!!!!!!!!!!!!!!!

[@s33therfan]

Thank you very much sir again for watching

[@baxrok2.]

As usual, you made it look easy! That baby is gonna purr like a kitten and pull like a monster now. Do a video on how it goes down the road when you get it back together. Thanks!

[@s33therfan]

+Baxrok2 will do , I know I still have bugs to work out of it . One of my cac boots sprung a leak after getting the turbo on . About the way it goes you fix one weak link and another pops up ha . It's not been too bad definitely been a good project . Thank you again for watching and the support along the way.

[@baxrok2.]

s33therfan When you post your videos do you put any tags in the box below the description? For example in this one you'd put stuff like, turbo, turbo rebuild, Ford turbo rebuild, etc,. If not you should as it might help get you more views. You deserve them!

[@s33therfan]

+Baxrok2 I did not know that , thanks for the advice . I'm definitely going to start doing that from now on . Thanks again

[@baxrok2.]

Yeah, the tags, as they are called, are for people doing searches. So, if I'm searching for say, rebuilding a turbo, YT will look for those tags in different videos. It can be quite specific or very general. In my videos, I go to both extremes. For timing videos, I put in tags like, "timing" to keep things general and then get super specific and say "2005 Mazda 2.3L engine timing" and then I do just about everything in between since it's very easy and only takes a minute. In your case you might say stuff like, "turbo rebuild" and then get specific with "Ford 6.0L Powerstroke Turbo Rebuild" and then mix it up with stuff like "6.0L Powerstroke" "Powerstroke turbo" and so on. Hope this helps!

[@1995jonjon2011]

Before the rebuild what the the truck doing was it building boost up to almost 30 psi and not having power?

[@s33therfan]

+Jon Melton Basically what had happened was once installing the engine in this truck I noticed the turbo propeller had slack end play. It wasn't until I ran into some other issues that I decided to go ahead with the rebuild . I had to remove the turbo anyway so it was a good time to do it. However I didn't run the truck long that way and I wouldn't recommend it for anyone else . Once it gets slack in the propeller or play it could come apart and ruin the turbo. Other than fixing the bearings and the slack I didn't notice much gain . I've however had more loss from leaking intercooler cac boots leaking and had to fix replace those . I will say the rebuild is very simple and most cases the kit I used is all you need unless there's some serious damage to propellers shafts in which case the cost of that most just replace the whole turbo. Hope this is helpful and thanks for watching and subcribing best of luck

[@rossdubois2959]

Thanks you so much 👍

[@s33therfan]

Thank you for watching.

[@rossdubois2959]

@@s33therfan - hi 👋, ) maybe you help me..??. I need a kit for 6.7 powerstroke turbo 11-14 with dual compressor…???

[@juanjaimes1836]

Thanks for sharing this, do you think one can get 25k miles out of a rebuild? I drive like a grandpa lol

[@s33therfan]

Absolutely, Thanks for the feedback.

[@snicks50]

You do not have to mark any thing. its marked already for you.

[@luischairez476]

Can i use the stock compressor wheel or do i need a wicked wheel?

[@s33therfan]

It is up to you , the stock will work but Im sure a performance would be better. Great question and thanks for watching.

[@manuelmarquez2237]

Good mechanical

[@s33therfan]

Thank you very much for the kind words , and thanks for watching

[@bluesman97]

Great Video.. Thanks for sharing.

[@s33therfan]

Thank you for checking out the video . I sure doesn't hurt to know what you're getting into before starting a project. I will say it was cheaper rebuild kit but so far so good it's held up just fine , and it's for sure 100 percent better than it was before the rebuild . Thanks again

[@KidKandyful]

Thank you so much for this

[@s33therfan]

Thank you for the great feedback, it is much appreciated.

[@MrOmargaytan1]

Hello, what's the kit name, or part number?

[@s33therfan]

I do not recall the exact brand but it was a cheaper one that basically looks like this one in the link . Thanks for watching Look at this on eBay www.ebay.com/itm/303530642419

[@samc5898]

Did you have to re-balance it after the rebuild?

[@s33therfan]

No I didn't , just put it back together and been driving it ever since. Like I'd told another person I have not been gentle on it by no means . I was sceptical myself about how the kit would hold up , but so far I would say it's been worth it. Only time will tell though. I'd had another turbo I thought about using but upon further inspection seen that it was worse pitted and scarred than this one so I decided on the rebuild . Hope you found the video helpful , please like and subscribe if it was . Thanks for watching

[@itsnotfar]

Install unison ring at 10 o clock. Am or pm ? Just kidding🙂

[@s33therfan]

Ha , thanks for watching.

[@rtorres2079]

Where I can get the rebult kit?

[@s33therfan]

I got mine from ebay it was one of the cheaper kits . Around 30 dollars . Thanks for watching

[@jtnoodle]

Annaseez. lol

[@franklauriekranitsky2782]

You can get motion sickness just watching this video! Good technical advice but your video skills could use some help.