ReCover Tactical P-IX “AR Platform” for Glock | ❗️watch this BEFORE you order ❗️

A small (or massive) shift in my content. The P-IX brace from recover tactical is described as a "modular" platform for you Glock to drop in to. you'll see in this video my comprehensive breakdown, firing test, and review. (spoiler alert, its not good)
(pew pew time begins around the 5 minute mark)
DISCLOSURE: I purchased this brace with my own money on pre-order and waited months to get my hands on it. I was stoked to test it out and figure it had promise to be a lot like and "apex" Glock bulpup conversion kit which is also great! as it would happen, this kit borders between useless and unsafe and sits right on the line of completely impractical.

[@cymond]

The irony? You cannot use this chassis with a SBR Glock! SBR markings are required to be visible, without disassembling the gun. This chassis covers the entire Glock, so there's nowhere to put the NFA engravings.

[@cheeko_914]

Then put a longer barrel on it and convert it into a rifle/carbine.

[@cymond]

@@cheeko_914 Almost nobody wants a Glock with a 16" barrel hanging out the front, especially without a handguard over it. If that's your thing, get the Apex Tactical kit. kzbin.info/www/bejne/i4fNZnmfftl7f80

[@cheeko_914]

@@cymond thats clearly what this kit is meant to be used as. Why would they put your hand and rails in front of the barrel with such a large opening if it wasnt meant to be used with a barrel extension like a suppressor?

[@cymond]

@@cheeko_914 Yes, a suppressor would be very nice. It's also off-topic, since we were discussing barrel lengths for legality. I highly doubt that a version with a 16" barrel would be popular. I only know of 2 companies that make 16" Glock barrels, and even those are uncommon. They're just not very popular.

[@Icriedtoday]

What the hell are you talking about? I've been an SOT for 20+ years and I have no clue of what you are talking about. The serial number? It's on the weapon itself--they Glock serial number IS the so-called "NFA markings." You just have to pay the stamp and give the ATF your Glock serial number, that's it.

[@allenpickett5307]

That is not considered a short barrel rifle if you put your Glock in there at the end of the day it's still a pistol.

[@bradfordperry5997]

Thanks for this video! I just found out about these and went searching for info and found you. My quest for a brace continues.

[@DeskPop]

They have a great 20/20/20/80 brace I made a video on! Go with that!!

[@rawchickensandwich]

Is it commercial spec? I’m not familiar with airsoft but I have an ar stock adapter I bought at a gun show for an ak74 and my milspec stock didn’t fit on the buffer tube. I had to get a commercial spec stock for the buffer tube.

[@Cleverbrotha]

I read through the entire Q&A section before ordering mine. On the website for Recover Tactical, it stated that it shipped with a Commercial spec buffer tube. The SB Tactical braces are designed to fit mil-spec buffer tubes. That’s why I ordered mine without the buffer tube and stock they included in the add ons. If you have suppressor height sights on your Glock, it was suggested to take them off. I also noticed that your Glock had an aftermarket window cut slides. I read somewhere that the lighter barrel may create an issue with cycling. Man don’t throw it away. Someone will take it off your hands with a factory Glock.

[@DeskPop]

I specifically mentioned i switched to my slide because I do not have optic height sights, I had factory height trijicon fibers! I have a factory barrel and lightened slide (because I usually run an RMR) we did encounter many cycling issues but intentionally left that out of the video because I have an upgraded slide. “Commercial spec” is fancy word for airsoft… it’s not a buffer tube by any specs because it won’t hold a buffer: it’s just misleading. You’ll also not in almost all their videos/photos they have a different tube that the one shipped with.

[@Cleverbrotha]

I am a bit concerned after your video since mine will be arriving soon. I’m not in any way discrediting your concerns. I added the commercial spec information because of width issue. That buffer tube is ridiculous. I’m glad I purchased mine without it. I was merely adding the information so that those running suppressor sights who may be considering this platform could take that into consideration. Also, I added the window cut slide info because I read that it created a problem for one of the other conversion kits for Glocks… I believe it was the Kidon Conversion Kit. So I assumed it would be the same here. My biggest concern is Recover Tactical’s ridiculous responses to your email. On their website they claim to have a “money back” guarantee for the P-IX…. Send it back. Get your money back. Just don’t throw it away. Even though that may have been for theatrical purposes only!

[@DeskPop]

@@Cleverbrotha They seem to have a “just jam it on there” policy 😂 My biggest concern is running this without a suppressor that results in destroying your lights and possibly hand… Also for the reloading/trigger/safety that makes me want to end my life when I use it

[@Cleverbrotha]

@@DeskPop I’m going to attempt to run mine with a KAW Valley Slim XL Linear Compensator since I have a threaded barrel. It will extend my barrel by 3 inches, keep all gasses blasting forward, and most importantly keep you from losing your index finger!!! I’ve already changed my recoil assembly. Replaced the 18lbs spring with a 13lbs spring. Hopefully that will eliminate cycling issues. Once I get it and shoot it, I’ll let you know if it makes a difference. So go retrieve it from trash before trash pick up day!!😂😂😂

[@theoffice9208]

@@DeskPop you seem to be running things not stock and not using commercial spec items on a commercial spec tube. So who is the one at fault here? Seems like you are

[@syrusdvirus2951]

Just saw y’all on 2A pro cast. Love the brutal honesty. ❤

[@DeskPop]

I knew someone would go back and find this… thanks for supporting us 🙏🏻

[@syrusdvirus2951]

@@DeskPop I had to. 😂 so glad I did.

[@kkkevv224]

authentic review. hopefully theyll make a 2.0 or 3.0 version bc i like the idea of it. guess you can look at regular AR9s but i like the compact truck gun design.

[@187chona]

Good review! Subbed !!

[@nmtay]

Good review. Just saw one of these in a picture and decided to look it up because it looked cool, as soon as you mentioned it being a Glock chassis, I knew it was trash. I guess if you're in a ban state and can't get an AR, something like this would be cool, but, for what the cost of the firearm and chassis costs, you could just buy a decent AR-9.

[@jonnycarcano]

As someone whose first gun was a Sccy, I don't mind the dogshit trigger that much. I have been through the worst of it after all. What bothers me is that the slide doesn't go far enough back to pull the round out, much less eject. Granted, that might be because I didn't lubricate it for god knows how long and/or I was using shit barrel. I did have reliability issues with that barrel in the past. I'll try running my 6-inch Wolf barrel, that's never given me any problems.

[@los3r908]

Almost grabbed one yesterday cause the caa micro roni I wanted was out of stock at Idaho guns. But when I pulled it out of the box it just didn't feel good. Glad I decided to order he roni online instead.

[@youhadmeathello165]

Thanks for a great review

[@DeskPop]

Thanks for watching my first ever video

[@cristophercinco8377]

Great review.

[@joseruano2004]

Do you know if it will work on a paintball gun

[@ivanchavez3013]

Does anyone know if i can put the ak underfolder adapter on it

[@JulkerReviews]

Just found your channel, you have great videos! Please do more pistol chassis or a video about backpack guns

[@DeskPop]

As soon as my budget allows it you got it! Making a video on a gun that does fit in a backpack here shortly..

[@jonathancarroll5740]

Thanks for your review, I was going to get one of those today but since the guy you reached out to for customer support was rude I believe I will take my business elsewhere

[@aaronhalili579]

I'm getting rubbish groupings even with the additional retaining screw. Tried to use a rail riser as well like another youtube vid shows for keeping the rail more steady, but at this point I'm more accurate shooting the pistol alone Shoulda tried it with a red dot so you could review the crappy accuracy too

[@DeskPop]

Even without the accuracy ailment this product is only fit for playing airsoft, and even not good for that

[@d.e.a.t.h2258]

Just saved me 350. I'm glad I looked up reviews and found you

[@boblupart862]

Got mine today. I really enjoyed shooting it! I put in a Glock 19 Gen3 Definitely a niche product in some ways but it is highly effective for what it is. I had no problems with the SBA brace nor any worry about hand burning. The safety thing, yeah okay I get how it can feel like crap but either shave it like this guy said or live with it. It is what it is. The only thing I hate is the mush in the trigger as stated. It sucks a lot when compared to an AR FCG but...I mean come ON. You are literally adding a trigger to a trigger. It isn't perfect but for adding as much utility as it does? For the price? 9/10 for me!

[@gracianomartinez234]

Basically its ok but do not order it with a stock, its illegal. The r elease mechanism will not release your basic ten round magazine. The problem with mine is only that.

[@cri8tor]

Thank you for the warning.

[@DiazPoopInThere]

I like this review

[@RealRickyRoss]

My kit included two approximately 1 in stainless steel screws with washer and nuts. Does anyone know what these are for?

[@DeskPop]

There should be some holes in your kit to put those through, and lock it closed even more securely than with just the clasps

[@wadewalcott740]

Thanks for the video. You just saved me $279. These things always look SO much better in my imagination!😂

[@bobotmeister]

true that. save mine too. 😅

[@jacobstaten2366]

Why wouldn't they make the tube fold?

[@cory5525]

I will stick with my Roni for my 19! Thanks you saved me 240 bucks.

[@dude...are-you-sure]

This review is a must if you were planning on buying this thinking this is an ar platformish clamshell conversion kit. the ar platform is a big misnomer very misleading. the ar grips i had was not compatible to this kit. the buffer tube system was the only ar compatible part. the quality of the craftsmanship is subpar for something this costly. the micro Roni cost less and is better made. 8:37 so i had to file out lots of the inside for my Elite Force G17 to fit and be able to be racked. id say this is just a toy for the airsoft kids...

[@andrewstallman111]

I wonder if your replacement trigger vs the stock trigger would effect the length that the linkage is pulling?

[@DeskPop]

I have an SPSR trigger in my carry. This kit actually has a spring behind the trigger that forces a long pull either way so we opted for the smooth Agency arms trigger!

[@andrewstallman111]

@@DeskPop Gotcha. I ordered a kit with none of the add-on junk. I'm more of the mind that it's just a fun range toy, nothing serious. I was wondering how the mag release would work. Obviously you have to work within the design of a glock. But like you point out it's in the way if you hold it there. Good video.

[@DeskPop]

@@andrewstallman111 mag release was my biggest complaint, it’s definitely very much just a range toy! Their actual braces are great. Just not this kit, Meta Tactical makes a sick drop in equivalent to this for about $100 more (and gives you a 16” barrel) Might make a video on that one next!

[@DeskPop]

@@andrewstallman111 definitely the best call to just order it bare, Areo sells buffer tubes for cheap that will actually work with a brace 😂 Reloading absolutely ruined it for us, it’s very irritating to handicap your ability to reload!

[@andrewstallman111]

@@DeskPop Yeah I've got an SBtactical tf1913 I'm hoping to put on. We'll see how it does, folding wise I mean. Only needed to order a buffer tub to pic rail adapter, but hopefully it's effective.

[@RMAN1231]

I found a lot of things wrong with this platform , am running a Glock 19 with a fake suppressor , I put a mil-spec buffer tube I had laying around with a brace on it , I fixed the trigger pull where it’s firing about half pull , , fixed the pistol grip that would not tighten, , running a sig red dot and open sights and holds around 2 inch group at about 25 yards , I have no problem with the mag release, if u know anything about guns at all it’s very simple fix , not disagreeing with you on some problems it has , but a few minor tweaks and mine is flawless now

[@DeskPop]

We can absolutely agree to disagree! I think if you’re forced to “McGiver” and spend extra money on a platform you purchased that promises to be a “drop in” system; you got taken. I know a fair amount about guns (I build and fix a lot of them) and I’d love to hear what you did to “fix” the magazine release. I will be making a video about their 20/80 brace soon, which is actually decent; but ironically their product broke before I even got to fire it so I had to order a few parts from them all over again. Imo, the inability to grab a magazine while your empty magazine is dropping on its own is enough for me to completely dismiss it from any sort of functional or practical use. I appreciate the comment, enjoy your kit!

[@RMAN1231]

@@DeskPop like I said I agree it has some issues, already had everything to fix it so cost to me , just parts laying around, may have miss lead u on the mag release, I have no problem how it is at all , I adapted to it , and I also build guns and custom all my guns to fit my preference

[@capitil2114]

@@RMAN1231 how did you fix the trigger pull?

[@firestarteronix]

Thank you, I almost made the mistake of buying one.

[@jessearroyo3927]

Very good!

[@jodee9727]

Thank You!

[@DeskPop]

Get a 20/20 or 20/80 brace if you like their stuff! They actually make GOOD braces, just a TERRIBLE pcc conversion

[@JamesKaret]

very interesting. i bought it for airsoft but haven't tested yet. i wonder it'll be different.

[@redghost0168]

I want to see that I want to do the same

[@JamesKaret]

Received yesterday. Using WE Glock 17 gen3 and 18C. They don't fit. Need to make trigger guard holder thinner. (Position is also out of line. Better grind almost every part of under barrel place.) Slide attachments are also slightly small. Even after the massive grinding, too much friction at pistol slide to operate well. 14kg puff dino (white one) gas is required to use it. Using on 18 is impossible. I drilled a hole to fit the selector, still, it doesn't fit. (unless it's on full-auto.) After those grinding, drilling, mag release is terrible. Kit is pressing it slightly, you might need to grind that part too, but it'll make really hard to detach the mag. ReCover says it'll fit on UMAREX licensed airsofts, so this product is only for VFC and GHK glock owners.

[@redghost0168]

@@JamesKaret damn, I kinda expected it to only be able to use the umarex/GHK

[@JamesKaret]

@@redghost0168 better have one of those to use it. or ready your tools, i guess. one thing for sure: it's not that worth your money. overall length with shortest stock is same as MP5. (or even GHK G5)

[@leofightsback6514]

And just 30 days if you still got that brace on , you going to have to register it as a SBR. If you register it, it will no longer be CPL compliant. So you can't carry it as a truck gun or on your hip. Local law enforcement said they are going to arrest anyone they catch with a pistol sporting a pistol brace

[@SK-me9by]

How about standing up for our rights and stop complying.

[@leofightsback6514]

@@SK-me9by hoorah I'm with that brother

[@WoainiHandong]

Thanks. I won't be buying this. Try the kpos scout if you can get it for cheap. I'll watch your 20 brace now. I watched Hop video a long time ago and didn't think it would be good. It's always on sale.

[@Cellus002]

I was about to buy this thing. Thank you for the video

[@SlippinYT]

This is your first video I ever came across but have you tried the MCK from caa? It’s the only kit I have but I really enjoy it

[@DeskPop]

MCK kit is great, recover has a brace that great too!

[@tomtolentino7575]

Simple solution to the spent gasses fowling the inner portion of the kit……extended barrel. Not only will you resolve that issue, but accuracy will substantially be improved 😎👍

[@angrycoder5520]

That trigger pull is a deal killer. for people who trains with live ammo only a few times a year. trigger pull is pretty much everything.

[@jimbeele6712]

The trigger pull is ridiculous...

[@adam100a8]

I’d it auto sear compatible

[@summers9911]

Wow,300$ for a piece of plastic trash...gotcha

[@Dariuswnebfjkhewfkew]

Dose this work with the psa dagger

[@DeskPop]

It does not

[@user-oz3yc3pl9v]

Damm that freaking sucks that it broke your front sight

[@AZBADBOYz]

Innovative idea but not ready for market clearly. They should make a dedicated lower that uses real AR lower parts, specifically trigger but the slide and barrel of a glock. This of course would have to be a serialized lower unit.

[@ariefwidyanto8734]

Dude.. thanks for the review.. I almost order this things

[@TSC1978]

I have one and they are LEGAL in Illinois as long as you don’t have a buffer tube and only a stock. AR’s are illegal. It’s 10 times more accurate than my Glock itself and my Glock Light does not obstruct shooting. I have a Red Dot on the top. It’s a great platform. The only thing you got correct is the trigger takes quite a pull. Everything else you got wrong. Changing mags takes me less than 2 seconds. Buy one! It’s $350!

[@thomasleigh8673]

I agree with you and also live in the land of “killinois” so understand the pain you are in as a citizen in this shitehole. That said this guy I think needs to go back to just playing computer games and making late night videos of him beating three year olds on Fortnite so he can feel like he’s a big man….but in reality the gun he is using for this video has probably seen more action than he has his whole life. Word # truth

[@Eric-mw1gr]

@@thomasleigh8673 Yikes. Are you the owner or just an unpaid shill?

[@boblupart862]

I bought this and its coming tuesday. I will let you know if its still like this.

[@hdua6772]

Any update?

[@boblupart862]

​@@hdua6772For reference I got the PIX-MG setup. Haven't shot it yet because I have family that got the covid and have been taking care of them. I will update again after I do that. Anyway its nice but out of the box the front and back rails are not aligned. Not sure if its damage or a hinge misalignment but I have an email out to them. No response yet but it was the weekend and it is labor day monday. My glock 19 gen 3 with old old aftermarket trijicon sights fits in perfectly. I was worried about my front sight on the glock but there is significant clearance between the top of the enclosure and the front sight so I am not worried atm. Trigger has a good amount of take-up but I think there is a way to adjust that. If not..well when I shoot it I will give an update on the feel. One thing I was worried about was the mag release button on my glock not working because it is a slimmer profile than the G17 but it works well. The charging handle is really cool in how it just clips on. Can confirm that you DO NOT need to attach the lower part of the charging handle for it to still function. It is somewhat uncomfortable to pull back. I feel that is due to the aggressive angle of the curve combined with its thickness. But not unbearable NOR is it a deal breaker in my opinion. It is nicely rounded so you don't feel like you are grabbing sandpaper. The forward mag well is as described in this video. Takes more effort than expected to remove a mag from it likely due to the way it's positioned at the front of the gun. I did not, however, feel like I would break the enclosure or the mag well by pulling on it hard so it functions as it should you just have to be firm AND sharp. I can also confirm that the safety does have that double position thing he talked about in the video. If all you have ever used was a good AR safety it will feel very sucky but for what it is I feel its fine. I won't be filing it down as @DeskPop did until after shooting it if ever. In regards to hand burning from the muzzle blast, as I haven't shot it yet I can't be 100% sure BUT in holding it c-clamp style my hand is behind the end of the barrel with the G19 gen3 so I doubt I will be uncomfortable. Is it physically possible to grip the enclosure with your hand far enough forward to be in front of the muzzle? Yes with my glock 19. I can't ever see myself doing that but it is physically possible. That might not be true with longer glocks though! One thing I didn't expect (which makes me feel stupid) is, with the gun in and two 33 round mags the center of mass moves very far forward. Not bad or anything just something I didn't expect as dumb as that sounds. Should be good for reducing vertical drift though! Over all the feel of it is solid. It doesn't feel like a toy or fake when the glock is in there. So aside from the wonky top front/ back rails being out of alignment I rate it 8.5/10. Assuming all goes well with the shooting I have added significant utility to my glock without having to modify the firearm itself. I call that a win. Will update after shooting it.

[@boblupart862]

@@hdua6772 Yes! I shot it today and I was very happy! Overall I give it a 9/10. I wouldn't call it an 'ar platform' like they do since you can't put in an AR trigger group. That is my biggest gripe, the mush in the trigger. But again, this is a calmshell enclosure that a gun fits in to so it is what it is in that regard. It felt super sturdy and tight while shooting. I was most impressed! The whole 'you will burn your hand' comments..nahhhhh! Not even close and I was never uncomfortable I'll put a video up of me shooting it. 9/10 for sure! Very happy with my purchase! I'll have a video up of me shooting it.

[@hdua6772]

@@boblupart862 huh I wonder if you put a timney alpha trigger in it will it get any better. The Glock triggers aren’t really the best and with the added pull I think it’ll make it worse

[@DeskPop]

@@hdua6772 I have a timney alpha trigger on my glock, I did a review of their 20/20 and it’s just a better system.. this is a cool idea with terrible execution

[@ElluzhinYT]

The convertion kit from CAA is better. Just saying.

[@slimmg7566]

So it's illegal to have I don't get it ?

[@DeskPop]

Become illegal the second you throw a stock on a gun without a barrel that has a 16” oal. So putting the glock in it how they send it, is committing a felony

[@bokii2284]

I like how honest you are with the review, there are points where you sound like you’re just hating tho. But hey you saved me some $$ by pointing out the drawbacks on it. Thanks!

[@DeskPop]

For sure; the company definitely deserves to be slammed after basically just calling me a liar for expressing my experiences. We just did a video talking about a product we like that’s not good too, and the company Emailed me thanking me for my feedback, and promising to revisit their pepper balls potency! This product advertises and was just advertised as something it’s really not.

[@johnwilson2181]

Thanks Karen. My suggestion is don't use the mag grip without a mag secured in it.

[@aggsup]

Can I have it? I wanna use it for science

[@jgross1991]

Is your shirt ok?

[@xxTenaciousExx]

What stock is that

[@DeskPop]

Idk my guy it comes with the kit

[@stevenjeffrey4637]

Cool that you corrected "site heights" to "height sites", but it is actually "sights", lol. Sorry,..I had to be that guy.

[@DeskPop]

its funnier this way

[@wood-wheel-wizard]

It’s under 300$ decent at that price.

[@sodalines]

the flux raider or the bt uswg are great and way better

[@gfoe1499]

Damn I wanted to like this but broken sight? Nah bruh I’ll keep my mck

[@DeskPop]

Yea possibly “my fault” for upgrading to trijicon fibers though! They do want only OEM components. I VERY wanted to like this, I pre ordered it and waited months. It’s just BAD!

[@granitejeepc3651]

Why did you not put sights or a dot on it?

[@DeskPop]

Because I didn’t talk about how well it shoots, it’s bad enough without getting into that

[@SuperAsian78]

Man sometimes I really don’t understand while the laws are the way they are…smh

[@risablima7924]

Will a glock 30 on it?

[@DeskPop]

That’s a wide frame glock so it won’t fit. I also wouldn’t consider putting anything shorter than a full size in this. I also wouldn’t even buy this

[@oscarfry324]

to me it sounds like you got a bad customer service rep and a bad P-XI case so little to no quality control see if you can find someone that has one and borrow theirs to compare it to your own

[@joshuawaddell6640]

I hope they listen to feedback and make some serious adjustments for a gen 2 version. CAA seems to have done this with their MCK. I bought the gen 2 MCK a little while back for my Polymer 80 and absolutely love it. I think this platform has real potential if they iron out some issues for future models. Good video, thanks for sharing, and God bless!

[@RemoteCamper]

A P80 DOES fit?? They make NO mention of the p80s fitting on their "fit chart", and I figured that the trigger guard would not let it fit either. That was the sole purpose I was watching this video.

[@joshuawaddell6640]

@@RemoteCamper I have the P80 for the CAA MCK Gen 2. It also comes with a Glock adapter as well.

[@jesserhernandez4182]

goffies! 1. pull the mag out of the fwd grip/mag holder by using your thumb as leverage. don't jank out. you look silly! 2. You are purposely pressing the mag release on the pistol. Just dont! 3. Get some sights pls. 4. safety, clear the weapon and don't point to self, even if it's not loaded. Goofy.... I couldn't bear watching on..... Stay Safe guys!!!

[@DeskPop]

1. The gun never pointed at me once this entire video. Not really sure what you’re watching. 2. “Just don’t” is not possible. You have a firearm recoiling, even zero pressure on the area will result in an unintentional mag drop simply due to it being bumped by recoil. You look goofy either way because this thing lacks any useable ergonomics! Carry on!

[@jesserhernandez4182]

you're prob right! I went as far as 0:43 and just stopped there. if it's a pros n cons vid, be fair. 1. How much time did you spend on your investment b4 posting? 2. It seemed as tho you were biased. You do realize IWI is the maker of this gadget. 3. it's not supposed to take the place of an AR. It's just meant to dress up your Toy. It's not for performance, it only provides stability, just like their other products.

[@DeskPop]

@@jesserhernandez4182 you can see immediately before at that point there’s literally nothing in it-are you a baby? Is an empty holster scary for you too? You probably don’t appendix carry because your gun points at you if you bend over. You can also clearly see it’s pointed up and away anyways. But I’ll GLADLY post me looking straight down an item that’s as lethal as a nerf gun Recover Tactical is NOT an IWI company. Not even CLOSE!!! It’s the DESIGNER of an IWI products company. Second; I spent plenty of time with my “investment” more than enough time to decide its trash, but I’m sure someone as knowledgeable as you would really like it! Go buy one.

[@DeskPop]

@@jesserhernandez4182 IWI makes great stuff, I recommend their AR’s to people as some of the best entry level AR’s out there all the time; totally cool being lectured by someone who knows something, but so far all you’ve done is prove you’re completely ignorant and have zero purpose here except to complain and make zero notable points. Go give them your money or become informed instead of just crying that “he flagged so he bad” about an empty brace.

[@UsoZoo]

@@DeskPop 100% sure he works at this shit company by the way he trying to defend this joke of a kit💯😂😂

[@user-nf8jr2ov8x]

Thank you so mach bro . Tuday i was thinking to order this prodact to protact my famaly we have here big war in israel 700 Civilians were murdered.

[@DeskPop]

Get the 20/20 for your glock from them instead; it’s fantastic and more portable. Highly recommend the Byrna body armor backpack as well. Body armor will do you a LOT of good. Stay safe brother.

[@skeebo8918]

@@DeskPopfud sellout

[@unkorichie2029]

May Lord God be with you, your family, and your country❤️

[@user-nf8jr2ov8x]

@@DeskPop Thank you very much brother, I wish you only the best

[@user-nf8jr2ov8x]

@@unkorichie2029 Thanks a lot bro I wish you and the whole family That you will be able to raise your children in peace and calm Sending a hug from Israel

[@jerstolp1]

send it my way...seriously

[@MonkKFBR]

Have an MCK. Have a 20/20 from this company. Love them both. Gonna get the P-IX because this was such a one sided review I can't take it seriously. Honestly, I haven't seen this level of whining about an innovative product in a long time. Clearly, they pissed you off and you decided to take it out on them by doing a hit piece. Try being balanced next time. Yea, it's got issues, I get that. Every product out there has issues. New/innovative products, in particular, set off the close minded of the gun world the most.

[@DeskPop]

When I see this I know you didn’t see that I Gave them a GOOD review on a good product like the 20/20. It’s not one sided, this product sucks.

[@Manhatn15]

So go Cz scorpion it is

[@DeskPop]

Honestly, I’d look at the freedom ordinance Fx-9 As someone who’s owned a scorpion I don’t recommend them! They can be fired while out of battery and crack in half.

[@DeskPop]

Cmmg also makes an excellent 9mm pcc

[@Manhatn15]

I’ll check them out. Thanks!

[@jw9517]

Song?

[@DeskPop]

Curious George- Nate Rose

[@jw9517]

@@DeskPop thx

[@chingh3714]

thanks for the info! companies who don't stand behind their products never last long anyways. seems like they didn't even bother with R&D before releasing it on the market.

[@theoffice9208]

Recover offers a 90 day unconditional money back guarantee, this guy has an obvious axe to grind and admitted as much to me in a previous comment

[@mmbsrusa]

Just get a CX4 or JRC and call it good. Keep the pistol on your hip in a holster where it's supposed to be.

[@DeskPop]

I somewhat agree with you, for this kit, it’s a waste- however; I do think there’s a case to be made for just throwing a brace or stock on your pistol, particularly in the cost to use department! Plenty of people buying “first time” guns right now are buying a glock and hoping to use it for home defense, which is great as long as you train with it and become at least capable with a pistol. Throwing a $200 brace on your glock when you realize your wife of ten years will not go shooting with you ever because “guns are scary” once you buy it at least gives her a fighting chance if someone breaks in and she has to use it vs. buying a whole PCC in addition to a glock. Personally, I’d love to run a Kriss or a APC9, but I often times find myself just grabbing my 20/80 braced G17 and throwing it in my bag or next to my bed because it’s so portable

[@Rubin5342]

The 20-20 and 20-21 are two of the best products ever built. This, NOT SO MUCH! //ji

[@kennethsmithjr4985]

Hard to dispel from user error or Gear fail… but got it it’s Trash

[@DeskPop]

I literally built and sold custom guns for a living when I made this

[@foofsamoyed]

Nice optics you have there. I bet it holds zero amazing

[@DeskPop]

Thank you

[@tragadocious-6357]

Thank you for saving me money. I almost bought this instead of an mck.

[@DeskPop]

Look at their 20/20 brace! I have a video on those I haven’t released yet and it’s actually awesome.

[@tragadocious-6357]

@@DeskPop will do

[@joshuawaddell6640]

FYI bought the Gen 2 MCK for my P80... LOVE it.

[@tragadocious-6357]

@@joshuawaddell6640 I've been looking at mck for a bit. I think it would pair nicely with an extended threaded barrel and suppressor. But at that point, you should probably just get a pcc. Either way, I have the kriss mag extensions for my 21, so the mck looks more attractive for that.

[@user-qy1fx3jg2j]

I don't know Glock has a cosplay outfit

[@jimbeele6712]

By the way, I have one for sale now.😂

[@FlyingTigersKMT]

The bad part about all that gas debris on the light is that there are tons of metal particles in it so when you wipe you'll scratch the crap out of the plastic lens.

[@sadaway4301]

Hop from tfb tv did a good review on the 20/20 that shows its not all that unless you get the riser for a sight, and its still usually too short to shoulder properly causing you to hunch up in an uncomfortable position- its a moot point with the brace ban rn but this chasis is undoubtedly sturdier and stabler with a stock. Recover did add a heat shield on the newest model but youre the only reviewer ive found complaining about burnt hands so- idk but doesnt seem to be an across the board issue. Its a chasis so ofc you get compromises but its the closest glock chasis to an AR receiver in terms of operations and dimensions- it goes without saying its not a 9mm AR but again- its a glock chasis not an AR, it won't out compete them it will do something different. Watched the full review but ultimately I'm deciding most gripes are non-issues at best and over exaggerated at worst when comparing to 2 or 3 other reviews out here.

[@DeskPop]

You’ll wish you bought an MCK

[@sadaway4301]

​@@DeskPopfor the trigger pull yes, but I may be going back to NJ and that's a no go with the brace on it by default so- but if I plan to use a short buffer tube on this for a cheek weld a la Demonstrated Concepts I'm sure it'll do the job just fine. Also got a slightly extended barrel for my 19 so that'll clear the front regardless. Imo the major con is a heavy trigger pull but for a defensive piece that's not a deal breaker. Potentially better ergos than the roni/mck too

[@DeskPop]

@@sadaway4301 meta tactical makes a SUPER effective conversion as well It has worse ergos for sure. I have my home defense gun with their 20/80 brace and it’s just a better setup

[@sadaway4301]

@@DeskPop meta tactical? Is that the bullpup conversion?

[@DeskPop]

Yes, its way more functional than this kit. Even after gen 2 I can't tell you this is going to be anything less than disappointing to you.@@sadaway4301

[@merc4hire308]

I have a question- how were you aiming without sights sweet cheeks! Next time, put sights on unless you have have a built-in red dot inside your eyes, which I doubt!

[@DeskPop]

I was pretty much expecting the cheap plastic to break apart while shooting and didn’t even talk about the “accuracy” of the kit. If I talk about how straight something shoots I’ll throw sights on it

[@1delta10tango9]

Why so aggressive?

[@mikemccoy3611]

Shooting without sights.?.?.? Hmmm. Until the ATF unilaterally outlawed this platform without congress or the president’s vote and signature, I put well over 500 rounds through this platform and had zero problems. Certainly none of the problems you had in this video. But none the less after the ATF illegally and unconstitutionally banned these I threw mine in the trash. But not because I didn’t like the platform.

[@DeskPop]

Disrespectfully, the type of person to say "This is against my rights, anyways I'm going to comply" is exactly the type of person to enjoy this kit.

[@areuokdaie]

So basically it's junk. Got it.

[@joshhouse6857]

If they fix these things it be neat enough. Though I'd rather get a carbine to get a subscription to Glock+

[@E3litecompany]

Well it’s cheap sitting at 274 so you can expect it to be cheap

[@wilez3219]

​@@E3litecompany that's not cheap to me 😂

[@jimmythebudgetbuilder7197]

@@wilez3219especially for a p.o.s 😅

[@dylanmijer2890]

It’ll be great for air soft😂, but for the price hell nah🤣

[@SNAKEDOCTOR99GT]

You can't compare that to a AR 15

[@turbo18eg]

Finally a real review on this thing

[@JasonPro420]

Imma stick with my MCK all day... better.... just.. better

[@trivantedrayton6438]

Facts

[@cpd969]

12:46 😣

[@DeskPop]

“You’ll shoot your hand off, Kid!” Or whatever the old guy said in that movie

[@jayilla28]

Great review

[@suttisakthavarasuk]

It's a good show, but it's not smooth. ; )

[@goowy1256]

Thanks for the review , im definitely not buying this.

[@capitil2114]

Shitty experience I have had says it will fit a Glock 23 gen 3 get it and the mag release does not even work for me but it does work for my gen 5 Glock 19 currently waiting on customer service to email me back because I paid for the full kit and it got shipped without the buffer tube and stock🤦‍♂️ Here to follow up they sent out my stock but forgot my buffer tube I’m so over this company 0/10 recommended for anyone looking to purchase this product save yourself your time and money

[@DeskPop]

They accidentally did you a favor by not sending you the airsoft stock and buffer

[@vedrisca]

Looking at all the negative comments here makes me think that there's way too many fanboys for the one-hit wonder that was the 20/20N Stabilizer brace. If the mag release depresses as you are holding it in the correct position (in alignment with the thumb rest), then that's simply bad design. And if the P-IX intends for you to hold the front magwell as a grip, why isn't the barrel shroud extended to support that position? The fact that you're slammed with ad-hominems as a small KZbinr without any counterclaims regarding the actual design of the brace itself goes to show how shady this whole thing has been for you. Thanks for taking the time and money to show to this to us.

[@DeskPop]

Thanks man; it’s honestly ridiculous as no one wants to talk about a bad design. I even gave their 20/20 brace a positive review; this one’s just bad and their company is even worse!! (They even chose to delete their comment after I pointed out they simply attacked my character instead of refuted my points)

[@MrBenjaminsisko]

This was almost a good idea I wish it worked better maybe they will remake it better

[@ed2335]

I'm guessing they should have tried to make you happy. Good video.

[@rednexicanusmc5884]

It looks cool. I like the concept but looks like a nerf gun. Might as well just buy a short barrel AR

[@mikie1466]

That would take a tax stamp.

[@2bad4uxxtwobad4uxx2]

Excellent review, now I will not be getting one...💙❤💣💥

[@jimbeele6712]

I bought it for my 40cal glock. Nothing but a$200+ dollar headache. Just a waste of cash!!!!

[@Glock45M]

Why?

[@jimbeele6712]

I checked to make sure my glock fit and it did. I had to modify all sorts of parts to get it to work. Just CRAP.....

[@asianmovement]

I got one and the minute I opened it I was disappointed. Customer service is sht. Instagram msgs are sht. product is sht.

[@typsyflacko1939]

Buy a flux raider

[@itsamk18-ish]

Based. #raidergang