Cletus’s channel is nothing but fun. This channel has a great amount of fun and a good bit of learning. I’m a huge fan of both. Keep it up fellas!
@overanDownUnder6 жыл бұрын
Shannon Sisk I was just going to say the same thing. I like how much detail is given on even the smallest detail. Awesome channels.
@nogainsnodames6 жыл бұрын
This content is fuccking dope. Eating up the knowledge. Also it’s pretty cool he’s got coop in there on the camera.
@breakupgoogle6 жыл бұрын
reroute that fuel line so if a tire blows it wont take it out
@matyLSX6 жыл бұрын
Thanks for tips. You guys are all great to watch. Your always showing us something your doing it building to give your followers ideas. Thank you for what you guys do....
@travissmith20676 жыл бұрын
I used the flex seal liquid on the complete outside of my tank and worked like a charm.
@JohnRoberts712 жыл бұрын
Love the detailed information
@samleisch13886 жыл бұрын
I'm sure you know this, and someone may have already said it. But I wouldnt run your PCV hoses in front of your mass airflow sensor..... and oil residue or fuel and itll ruin the sensor and ruin your ability to tune it or if it's enough fuel... kaboom
@MrLom6546 жыл бұрын
cooper: I race with no clothes on so that saves weight! hahah
@beforebefore6 жыл бұрын
How can you create a vacuum in the air-to-water intercooler if it's "open"?... the trunk ice tank can't seal well enough to create sufficient vacuum. Temporarily cap those lines off? ...or just suck from that high point in the front water-to-air heat exchanger? Then I have to ask how can you possibly prevent it from getting air bubbles when you launch... if that big tank in the trunk has air in it... surely you'll occasionally uncover the pump inlet on a hard launch... no? Do you have to map the methanol intake cooling spray into the engine fuel map? Will it begin injecting at a certain positive manifold pressure, or RPM, or what? This takes me back to the early 90's when I put a water/methanol vapor injection system on my Gen2 RX7. Sorry to mention non-Uncle Sam related vehicle here... but this was after I transplanted a '78 Buick Turbo Regal V6 into my '76 Skyhawk, which I hacked the potted oem engine computer in order to take control of the wastegate - and give me a point to also control the water injection I put on it)
@michaeldeaton17886 жыл бұрын
Can't wait to take my slomaro to Jeremy !!!!
@MichaelBacon2126 жыл бұрын
Hey Jeremy Get some Flex Seal for the water tank. The stuff really does work amazingly.
@stykytte6 жыл бұрын
I don't know, I've coated my computer with it but the internet still keeps leaking terrible Flex Seal memes.
@123vaw1236 жыл бұрын
@@stykytte cringe
@Briceon6 жыл бұрын
@@stykytte You must not have filled the ethernet port. That should fix your problem. Gl
@country63686 жыл бұрын
It really does not work for shit
@fuckeththou89256 жыл бұрын
@@stykytte funny that you say that and make one of the worst flex seal jokes ever.
@judeh1016 жыл бұрын
Sounds like Cooper filming
@maxmillion42166 жыл бұрын
Jeremy, That beard must weigh 6lbs plus another 10lbs for your low hanging fruit....lolol..! Can't wait to see you drag'in them Cleetus bald eagles..!!!
@orb1talnz6 жыл бұрын
why not use a deadhead fuel system? it would also reduce fuel heating...
@FixItNick6 жыл бұрын
Bilge watched 7 parts whew... love it man, you could have used the tire compartment, fill it up with water and stick a water pump at the bottom lol
@AKay4tothe76 жыл бұрын
Stopleak will take care of all of that business.
@MagicModzzCOM6 жыл бұрын
Jeremy the hair bro😅
@HondaForLife946 жыл бұрын
You should make an intro for your videos. Dress up like your “I want you to make some power”. Then maybe have some other videos of you doing some burnouts or sprinkling the magic dust to make more power.
@greghuff3436 жыл бұрын
Most police forces keep and destroy the ballistic panels in this area. I guess they don't want a handful of cheap bulletproof cars running around. That said if they are in there they are very heavy.
@r4ng3k03r16 жыл бұрын
Get a couple of lithium batteries they weigh plenty less than those heavy ass bricks you're using now it'll save you a little bit of weight
@ELJEFEEEE6 жыл бұрын
Did a cow lick your head?
@SortaProfessional896 жыл бұрын
Hahahahaha it really does look like that! It could be the 12 dogs he has as well but ill think cow until told otherwise.
@watahyahknow6 жыл бұрын
about the tank fillertube : you could shorten it and fill it from a resessed fillerneck build in the rear doorjamb photobucket.com/gallery/user/fabmaster23/media/bWVkaWFJZDo3MjI0OTUxMw==/?ref= unless you spray the gas all over the upholstery it should be a nice solution
@picklebacon6 жыл бұрын
Dropping some knowledge!
@nickmudd6 жыл бұрын
Do I hear iRacing in the background? lol
@Drolfuus9996 жыл бұрын
Love the channel keep it up, hope it becomes profitable for you! You have good opportunities
@CTemple826 жыл бұрын
Great videos man, lots of good information.... This is good safe budget building at its finest and NOT hackery cutting corners bullshit like some of these other guys on KZbin...Great content, keep it coming.👍
@jon1060226 жыл бұрын
Finally a video! I was worried about u man. But i seen u in cleetus videos so i knew u were good lol
@picklebacon6 жыл бұрын
Someone is gay for Jeremy
@jon1060226 жыл бұрын
Someone is childish af
@joshieOle876 жыл бұрын
I ain’t gay but 20$ is 20$
@GodzillaSVTMACH16 жыл бұрын
You should let out all the air in the tires and put Helium in them. You know Helium is lighter than air! Rofl
@Redline_ratchets6 жыл бұрын
Ba ha ha ha ha
@froggersgarage51276 жыл бұрын
It would weigh more because you use more
@neutron6146 жыл бұрын
285/35r20 2013 camaro 1LE 2SS zl1 style wheels fit right on and the brembo calipers we have 13 of those cars for parts
@RoyBoy20206 жыл бұрын
You got a cradle and rearend??
@michaeldeaton17886 жыл бұрын
You have wheels for sale ? And what state you in ? ( fingers crossed for Florida )
@neutron6146 жыл бұрын
gimo2055 were in ohio
@neutron6146 жыл бұрын
Rivers edge auto sales
@BLSdesigns6 жыл бұрын
Jeremy I really enjoy your videos lately! Gonna be tackling a fuel system myself pretty much the same so was nice to see a little bit of what is gonna be involved.
@10100rsn6 жыл бұрын
First bucket leaks into the inner wall of the cooler. Then it leaks to the outside once the inside of the cooler is filled.
@kylemcintyre86276 жыл бұрын
You should flex tape the inside of your trunk where you had to cut the hole for the cross member.
@capnslufox6 жыл бұрын
Monster plump? Sounds cra cra
@pizzacrusher46325 жыл бұрын
budget builds sure are easy to afford when you have all the parts "just laying around." ;)
@samnorman99106 жыл бұрын
Just wondering - On the water cooled intercooler, if cooler is better, have you considered running something different like anti-freeze cooled with crushed dry ice. Seems like that would drop the air temperature much lower than water / ice. Is there a limit on how cool of an inlet air temp you should target?
@JasonLeaman6 жыл бұрын
What are you going to do when you launch the car and all the water goes to the back of the water box and no water goes through the pump ?
@yourtechstation6 жыл бұрын
Mr Dashpuppy from my understanding of the system in the video, the pump is towards the back of the water box plus he needs to put more water in it. Also it’s a closed system so it shouldn’t loose any water if Jeremy fixes the leak.
@JasonLeaman6 жыл бұрын
gotcha, thanks!!
@joesilvasr97335 жыл бұрын
You can source very inexpensive bulkheads to remedy that leak. Amazon aquarium section or any local AG Supply store.
@rickybobby03146 жыл бұрын
Love your videos!!! Learning somethings, and I appreciate you taking the time to show what you are up too. It’s so much easier to just show a fast car rather than, doing what you do and show the build up of a car.
@typedrew6 жыл бұрын
Leave the battery in the back. Delete the one in front.
@ransomholbrook74286 жыл бұрын
Not a fan of Methanol for this application. Ethanol would be better, not nearly as corrosive, then you could use E85 to drive it around on the street with just a tweak of the tune. Hope that fuel pump survives.
@WelLRoundeDSquarE6 жыл бұрын
I would have to agree with your theory on where to put regulator 100%. It's the only way you can ensure you maintain pressure in the rails. Of course it's just my opinion.
@vortecturbo6 жыл бұрын
Jeremy with all due respect you be better off doing the regulator like what you were talking about having it feed up to the rail have it go with boost pressure rise put the pump on kill since you're doing a return style system and then have a short piece feeding your fuel rail without shopping that up between time labor and materials you be better off getting a hold of Jesse at Olsen Custom works and have him get provide you some Billet rails
@6iixzero7005 жыл бұрын
Saudi’s favourite car caprice 😎 They already made caprice 2015 1000hp in Saudi
@Adriansitos6236 жыл бұрын
Why don't you save 45lbs of weight by switching from lead acid battery to a lipo battery? They weigh in at 5-7lbs depending on crank power. That is a huge savings in weight
@biggin54346 жыл бұрын
Cost, he's trying to do a budget build and lightweight batteries aren't cheap.
@vortecturbo6 жыл бұрын
Feed the rail from the pump have it t out to go to the regulator for your return then you won't have to worry about any fuel pressure drop issues whatsoever until you're making some really big boy Power.
@Blackinterceptor9996 жыл бұрын
Tell Cleetus to upgrade the dang suspension on neighbor, that will solve the wheel hop and make it a LOT safer.
@justinvasko35776 жыл бұрын
If you add some salt to that ice tank you'll lower the temp of the water even further! I don't remember the ratio. It's no different than adding salt to the ice on a hand turn ice cream maker
@Andrewlang906 жыл бұрын
I looked on the website, and I couldn’t find “Natures bracket”, is it out of stock? I’d like to order one
@disgruntledegghead69236 жыл бұрын
Lookin good for a "budget" build, can't wait to see where it really goes. And yes Jeremy, run your tranny as hard as you can. I still cringe a little when people call em trannys, especially when they say they're gonna run em hard.
@geotoo41176 жыл бұрын
Jeff Knebel Zip ties and bias plies says it best " the Bruce Jenner"
@disgruntledegghead69236 жыл бұрын
@@geotoo4117 well said, I watch his channel too!
@crazzymonky6 жыл бұрын
People really on here trying to give this man advice 🤦🏻♂️😂😂 like I understand y’all wanna be involved and helpful but damn, you don’t think this man know? Lol come on guys. But awesome video, it’s cool how you explain all the little tricks you are using to achieve different things.. it would be cool to see this run against the dale truck, the V, and neighbor. 4 lane strip and just have James thrown in to give y’all a high number to try and reach!? That would be sweet.
@lingenfelterzeeohhsix81546 жыл бұрын
Jack Daniels right???? This is Jeremy owner of Fasterproms!!! Held (holds) THE WORLD RECORD for fastest c7 corvette and fastest ATS-V and fastest CTS-V cadi ON EARTH!!!! I think he knows a bit of what he's talking about ,....JUsT fine lol. Think that every time I see a basic comment , yikes people!
@paulhouchen90106 жыл бұрын
A wise man always takes advice good or bad.
@richardstevens3206 жыл бұрын
It would be good videos if you would ever do some work during videos in stead of just talking the whole video about what your going to do
@XxiMcRAzYLaZyxX5 жыл бұрын
I don't think you mentioned the pump you put in the ice box. Do you have a part number?
@dirdidarod6 жыл бұрын
Would be an awesome idea to dyno test steelies, stock aluminum rims, and some aftermarket rims.
@JohnnyAnderson16 жыл бұрын
Cooper is learning so much, love the channel! Cant wait to see the V and Sam run GOD bless!
@WelLRoundeDSquarE6 жыл бұрын
coffee enemas are more fun that pepto and water ... just sayin
@corwininadsm6 жыл бұрын
Full meth might eat away some of the aluminum blower, but fuck it.
@JMJM752576 жыл бұрын
Trim the underneath of the hood. The "honeycome" That must weight a bit.
@srbman69414 жыл бұрын
Can you do a Vid on MAS please, what do we use when & why? Thx
@solocamo36546 жыл бұрын
7:50 exactly.. I went with a softer tire that also was 3lb's lighter than factory. 3lb's per corner but it's as far away from the center as possible. Felt it in acceleration - but please keep in mind the car doesn't even weight 2600lbs.
@M3rVsT4H6 жыл бұрын
Loving this build. Hey might I suggest an elbow on the cooler return which brings your return line below water level. That way it won't suck air back into the system every time you switch it off.
@slacktantrum87486 жыл бұрын
Smart dude. I learned much. Enjoyed it much. Solid episode. This channel could be at the top with more tire smoke and broken diffs.
@ldnwholesale85526 жыл бұрын
PCV? Simply breath the engine into a catch can. Ideally breath the valley as well as both rocker covers. 3/4 "hoses
@HellTriX6 жыл бұрын
@Fasterproms Use a holly Hydramat to suck the fuel from both sides of the tank? :)
@davidwindsor28666 жыл бұрын
Starting to get there. Is Cleetus better friends with james then Cooper. Due to Cooper. Doing late night camera work with Jerremy. I don't know.
@SortaProfessional896 жыл бұрын
Just a quick question, so the blower had a screw go through it. Will it still make power like an undamaged one? And also will you put a different blower on it if its not going to be as efficient as a undamaged one?
@curthatt64616 жыл бұрын
Wow! Some complex stuff there! Good luck with everything. Great video and of course the dogs are awesome!
@ridingwiththereids6 жыл бұрын
Freaking AWESOME to see Coop on this channel as well!! Keep up the awesome work man. We all know you're doing the editing for 2 channels now, yet people still talk shit. Don't listen to the haters. You're the man Coop! And for Jeremy, thanks for all of the knowledge man!! I absolutely love the channel!!
@Fasterproms16 жыл бұрын
Coop is a good guy indeed! However garret does all of his editing for their channel and my wife does all of mine. Cooper has a solid role
@ridingwiththereids6 жыл бұрын
@@Fasterproms1 well thanks for the correction. Either way, both channels are bad ass!! I love the content man!!
@motodenton6 жыл бұрын
Man I love seeing a channel that goes so Indepth on what your doing and why. But at the same time you still send it. Great content keep it up brother.
@teazz38126 жыл бұрын
Bulkhead fittings anyone?
@wobblysauce6 жыл бұрын
+
@shartne6 жыл бұрын
Your gonna want to cover that hole up in the trunk to keep the smoke out.
@avoinc77076 жыл бұрын
how much information? all the information!
@charliemcmillian80846 жыл бұрын
The crash bars in the doors are heavier than you think.mine was 34 pounds each in a 93 foxbody
@dannyneal97476 жыл бұрын
Nice hair, I take it you used the same gel that Ben used in Something about Marry??
@nataliedeyton68296 жыл бұрын
Unexplored territory is always fun 👍 no one better to do this build. I truly enjoy this
@MJ-MJ-196 жыл бұрын
I used evap as a return, then I needed to add a breather from the tank to the gas filler.. Or it was hard ass hell to pump gas..
@richardharris4926 жыл бұрын
There's plenty of just send it fuckers on the internet already thanks for the content awesome
@sirnate546 жыл бұрын
Great videos, but you need a intro.
@tylerwildman71196 жыл бұрын
You need... FLEX SEAL!!!
@bradleyt38206 жыл бұрын
get a hole saw and start turning all that sheet metal into swiss cheese every pound counts
@jaredthisdelle56176 жыл бұрын
Love the vids man .she's not heavy my grand prixs is the true porkapotamas lol 4500 with driver ..looking to top swap it .soon ..i have everything for it would love it if u could do a quick review on 3.8 top swaps Jeremy there's lots of people ....keep up the gd work man ....
@nl98876 жыл бұрын
Jared THISDELLE how 4500??? My gtp is 3200 with driver
@steveg22776 жыл бұрын
Exactly how my fuel setup is run. It just makes sense.
@The-Life-Of-Brannon6 жыл бұрын
Jeremy you need to put a old police light bar on the top of Uncle Sam. Or red and blue leds inside of the front and rear windshield
@lingenfelterzeeohhsix81546 жыл бұрын
334videos LOL was just thinking ; I live in utah but served a church mission in Detroit and the state police there use the HuGe trash can looking red single lights Ontop their blue statie cars lolol how cool would that be!??.....Ok not so much, now that I think about it, funny but not cool lol , have two siblings that are cops (highway Patrol and sheriff) let's get a cool clear LED low profile light bar up top! Lemme see what I can do!
@JohnRoberts712 жыл бұрын
Great content thanks for sharing
@JR368026 жыл бұрын
Hey man it's pump not plump unless plump is a part I don't know about
@philipk856 жыл бұрын
Awesome video I am so excited to see this thing run down the track
@richardharris4926 жыл бұрын
Never tested it? what! this just send it shit MUST STOP
@rupertkingsley6 жыл бұрын
Were you talking about unsprung weight re wheels and rotor weight?
@jacobhaberhauer65526 жыл бұрын
What’s some good bolt ons for a 6.0 lq4?
@teamrotax5506 жыл бұрын
I’ve been waiting so patiently for this video lol
@mick4886 жыл бұрын
Get some alloy checked plate and patch up that hole you made in the boot. Get a hole saw and cut some holes in it to run the heat exchanger hoses and seal it with rubber grommets. 👍take care mate 🇦🇺
@wobblysauce6 жыл бұрын
Does not need to be Alloy, a bit of plastic even.
@civicsr2cool6 жыл бұрын
You do way too much damn talking
@sintwo0one6 жыл бұрын
Great Afterhours content.
@danpeltier13546 жыл бұрын
drill all you can farm part hard to do but it work for me .
@chevroletmickey1436 жыл бұрын
Love tech talk. Keep it up and thank you
@PNW_Car_Mods6 жыл бұрын
Go Cooper!
@wokkez30076 жыл бұрын
My turn signal is on hyper flash notification squad