Reduce small(portable) generator petrol consumption with this three easy steps.

[@bencoinstitute]

Pls Fam do well to subscribe,like and share our content.... Let's make this Hardwork pay If you want a specific Video just let us know via this comment section

[@emmanuelzheamos5661]

Video on you to put piston and connecting Road, for hunder generator's sir

[@bencoinstitute]

@@emmanuelzheamos5661 Check this out kzbin.info/www/bejne/o2eogYylmbiIhdU

[@chukzmoi-lg1em]

Pls how to use a 2900 armature on a 3000 firman engine.

[@vincentrobinette1507]

There are a couple of things to note. First off, the speed of the engine is directly related to the line frequency produced. Many motors, like those in a refrigerator/freezer or, a fan, are frequency specific. Lowering the speed of the generator also lowers the speed of these induction motors, regardless of voltage. Second off, the screw you pointed out only controls the idle mixture of the carburetor. When loaded, the mixture is controlled by a main jet located inside the float bowl. To change the fuel mixture while loaded, it is necessary to change the aperture size of the metering jet located in the same tube that the bolt threads into, that holds the float bowl on. You are spot on, with the fuel consumption being dependent on the load. Every generator in the world has a 'best efficiency point' called Brake Specific Fuel Consumption, which is an operating condition where the generator will put out its absolute maximum kilowatt hours, per Liter of fuel consumed. That normally occurs at about 70-80% of its maximum rated power. To save fuel, it's important, to choose the smallest generator that will power the load reliably. Running a large generator lightly loaded will consume more fuel, than a smaller generator running closer to its rated power.

[@bencoinstitute]

you are spot on with your Analysis, however just to be sure of how the screw works, try loosening it and compare the fuel consumption...you will notice a big differential. Thanks for your input vincent

[@sanctusetverus]

This video is amazing. That screw in the carburetor, I think it's the Idle screw that allows fuel to enter then generator even when the butterfly valve is completely closed. So the generator won't turn off if it's the speed is too low

[@xiacadecongo4551]

hi engr Benco , that flat screw head bolt to tighten in the carburetor to reduce fuel consumption, where could i find it in the sumec firman spg 1800 pro max , cuz I've checked on it, i found only star head bolt at the bottom of the carburetor , i didn't see any at the top beside the combustion chamber zone in the front like it's shown in the video . I'm eagerly waiting for your response . Thanks .

[@JoelByllz]

So my generator mechanic set my carburetor in a way that it consumes 5L in 3 hours.. with this video I’ve been able to adjust it. Sound’s changed and I’m testing to see how long 5L will last

[@DingDingMandarin]

Good job Onoseyonalu. Thank you for sharing.

[@bencoinstitute]

Thank you sir/Ma

[@gheckopoint5643]

Hi, good videos btw, greetings from UK. The machines you show look like they get some real use, are they used everyday for people’s homes and shops etc?

[@bencoinstitute]

Yeah

[@boyotoritseju8053]

Nice one bro, thanks for the enlightenment

[@bencoinstitute]

Thanks bro

[@dereal_bizzybrain2801]

Thanks boss… this is so helpful

[@TiktoklinaTV]

Ahhhh mere looking at you, you look more of a model than an engineer, I love your videos btw🥰

[@bencoinstitute]

Awwnnn...thanks

[@Terryclintonmusic]

😂

[@bencoinstitute]

Lolz...Terry... Y are u laughing?

[@Terryclintonmusic]

Because its clear from now on that she will only watch your videos to see your face and care less about the content of the video. 😉

[@osajeyfo]

Thanks from naija 🎉

[@bencoinstitute]

You are welcome brother

[@T0licYanki]

Remember that according to Faraday's law the absolute value or magnitude of the circulation of the electric field E around a closed loop is equal to the rate of change of the magnetic flux through the area enclosed by the loop. So if you decrease the speed, you decreases the induced EMF and invariably the power. It is also linked to the First Law of Thermodynamics.

[@bencoinstitute]

you will only consider all this if your aim is not to reduce fuel consumption

[@bulusnomaudu1782]

Pls how do you adjust the electrical Frequency (Hz) of a generator. Thanks

[@bencoinstitute]

by varying the speed while taking note of data on your frquency meter

[@Plutowave]

You’re amazing boss love your video 😊❤

[@bencoinstitute]

Thanks so much

[@bhatwaseem419]

Sir when we tight this screw anti clock wise it reduces petrol am i right i have som confusion plz tell me

[@bencoinstitute]

No, anti clockwise(to d left) increases petrol consumption

[@trigga6968]

please whats the best small generator to buy in nigeria ( 1.5kva to 1.8kva) that can carry small fridge and light bulbs

[@bencoinstitute]

Even though I don't recommend the 1900 generator for some reasons.... But the Elepaq constant with oil switch looks good

[@trigga6968]

@@bencoinstitute whats the best budget friendly kva i can go fro then sir and if possible i can know the price range i should work towards

[@onyedikachi6037]

Thank you Sir.

[@bencoinstitute]

You are most welcome

[@paulraymond5317]

Please explain the difference between running watts and starting watts

[@bencoinstitute]

running watts is the continuous power(watts) the generator can produce while starting watts is the generator peak power(watt) which is a momentary boost to power motor driven appliances like some refrigerators... you know this motor driven equipment requires a large amount of power for a short period of time to start running so that is where the peak watts come into play

[@JosephDavidEshilama]

Good day, how do I go about a generator making an unusual sound when trying to turn on with its remote and end up not coming up but turned off when using the remote to turn it off after a manual start.

[@bencoinstitute]

Oh.... Have u tried turning on with the key too?

[@JosephDavidEshilama]

@@bencoinstitute it has no key but a remote and a sensor starter, so I have been starting it manual this days

[@bencoinstitute]

Check your battery

[@prymnet8594]

Please which engine oil can I use for spg8000e2

[@bencoinstitute]

Oh Sumec fireman has their peculiar brand of Engine oil... That will be fine if you can get it.... In Absence of that i will advice you go with Golden super ..

[@circle19realty]

Can I change a alluminium coil generator to copper coil?

[@bencoinstitute]

Yes sir

[@Blacknarrates]

I just had to subscribe

[@bencoinstitute]

Thanks for the sub We appreciate

[@muhammadshettima42]

I unscrewed the golden screw two times. Will this negatively affect the engine in the long run. Its working fine now though

[@bencoinstitute]

No.... It won't

[@adeboyeoladimeji3329]

if you unscrew it means you allowed more fuel into the engine.

[@johnsominosonsinterbiznglt1036]

Nice one ☺️

[@bencoinstitute]

Thank you! Cheers!

[@Lozzybeatz]

Wow.... Nice work

[@bencoinstitute]

Thanks Man

[@emmanuelzheamos5661]

Waooo thank yoy

[@bencoinstitute]

You are welcome

[@emmanuelolumoroti4378]

Best one bro.

[@bencoinstitute]

Thanks my G

[@lasedikarabobandile5707]

With this point can one put on ac

[@bencoinstitute]

If you use it for very heavy load...it is advisable you don't temper with it

[@makaingoma2879]

Is there a down side in adjusting the carburator??can it harm your engine?

[@bencoinstitute]

Yes,if you adjust too mucj If you adjust too much your gen works on lean..ie the generator doesn't get enough fuel need for proper working

[@osajeyfo]

What it is the name of the screw driver

[@bencoinstitute]

Is a regular screw driver A flat or star screwdriver can do the job

[@joekeyzzpianoministry382]

My battery keeps draining. Even even I bought a new it didn’t even last one week

[@bencoinstitute]

What king of Generator

[@joekeyzzpianoministry382]

@@bencoinstitute Firman remote/key start 3kwa sir

[@joekeyzzpianoministry382]

It is the same type with one you used for this cover on this video I am commenting

[@babs8282]

My new senwi generator consumed 10ltr in 4hrs

[@bencoinstitute]

That's too much Man

[@kalitbh5250]

Hello did you later fix the issue and fuel consumptions