Removing and servicing the brush and clutch Dyson dc07- DC14-DC33

Monroevacuums.com
See our Non-commentary video if you want to skip to the clutch instead
Parts- needed
Torx T15 and T10
Flat head tool (screwdriver is an easy choice)
Belt- bit.ly/3Da3Gpl
Belt puller: bit.ly/3rs3EHu
Brush- bit.ly/3EoVKSw

[@Fallon19]

Watched a couple different videos, but this was the one!!! Thank you!!

[@monroevac]

You’re welcome, my pleasure 😇

[@LLStacheLarry]

I well be watching your videos.

[@paulwayne2602]

Excellent. Well done step by step video. Loved your voice and your humor. As an added tip for someone like me who had difficulty with the snap ring, please show the indentation on the rod just before you reposition the washer and the spring as you resembled the clutch. As I worked on my clutch, I couldn't see the indentation once everything was reassembled and ready for the snap ring placement. I was frustrated with the snap ring because I wasn't able to position the rod and ring correctly. My fault. I watched several other videos and no one showed the indentation on the rod. After spending time with the rod and ring not being able to snap it in place, I removed the inner parts, placed them in a stacking position and looked closely at the rod itself. Then I saw the indentation and within a couple of minutes had the snap ring secured to the rod. Again great video, great audio and step by step.

[@monroevac]

Thanks for the tip- Always learning

[@randalramsey605]

I am so anxious to sit down and watch this! Thanks for unlocking the mysteries of Dyson engineering!

[@monroevac]

Hope you enjoy it!

[@mevk1]

Nice clutch breakdown - thank you!! Us amateurs can say f.. that tool all you need is a screwdriver and leverage.

[@monroevac]

Yep

[@davidfarmer1666]

Thanks for the instructions.

[@monroevac]

You're welcome David. As you enjoyed the video

[@wcdaniel7]

Outstanding video!! This video greatly helped me replace the belts on the clutch.

[@monroevac]

Glad it helped!

[@thomaswrinkle2038]

Loving this so far! I realized that the tape helps the plastic not to crack when you pry the piece off with the screw driver. Another video had a kid just pulling it out with his fingers. I could not, nor could my weight-lifting son. His Dyson was yellow though, so I think it's built slightly different... Went out and bought a T15 screwdriver and it was about a 1/4 too short. I chopped off about 1/2 of the plastic handle with a chisel and mini sledge. I was proud of myself.

[@monroevac]

Great work Thomas. I remember how excited I was when I finally figured out how to fix it

[@nickm455]

If you tilt it all the way forward or backward I cant remember it comes out really easy by hand.

[@nickm455]

Tape is a good idea though.

[@monroevac]

Thanks for the tip, I’ll check out

[@jayambermsp8000]

Excellent repair video. I recently fitted some new belts on my clutch and the clutch works perfect. but when the machine is upright, it tries to spin. Do you know what it could be?

[@monroevac]

Not sure what could cause that - this model doesn’t come with a micro switch that can malfunction- I’ll have to inspect a model like yours to better understand the cause

[@timturner6613]

They don't make Dyson belts for the clutch . They do make some off brand belts .

[@vickimoorman5404]

What if belt still doesn’t turn after all this?😊

[@monroevac]

Check your brush. Try removing the end caps, sometimes they collect a lot of hair and carpet fiber. If the brush is fine. The consider replacing the entire clutch with a new one

[@rkidlat]

I cannot get the t15 closest to front off. It has resistance but it doesn't come out. It just turns and turns with about 40% resistance. Not sure what it's connected to. A loose nut? It's not the clutch cause I have the replacement and I can see the screw doesn't connect to it. I'm so frustrated. Am I screwed?

[@monroevac]

When say the front, do you mean the front section of the black cover?

[@LLStacheLarry]

Do you repair vacuum cleaners for people?

[@monroevac]

Yes.. visit Monroevacuums.com

[@LLStacheLarry]

@@monroevac awesome. I was thinking of getting into it. I have like 30 of them in the garage I found on side of the road. I like trying to fix them. I would like to get into fixing for people. There is nobody on my side of city/ town that does it.

[@monroevac]

@LLStacheLarry go for it. One at a time😊