replacement of gear selector cable If this video has helped you please buy me a coffee www.paypal.com...
Пікірлер: 24
@steveturner4214 Жыл бұрын
Super helpful thank you mate. I've recently had the cable replaced but its been super difficult to get it in the right place to find the gear. Sounds like its too loose and i just need to tighten the cable a touch.
@Witteringtrucker Жыл бұрын
Spot on video bud. Needing to do mine on a citroen relay. Struggling to get reverse and 6th gears.
@davidkidd20332 жыл бұрын
Very good and helpful
@leahfindlay92586 ай бұрын
Love your video. So helpful. However, I went to fit my new cable and it's too short! I used the OEM number from the old part, they matched but there is a 20cm difference in length. I can't seem to find a new one that's the same length as the old one. Any advice would be appreciated.
@fuelheadjay88006 ай бұрын
There is a few different lengths out there measure your old one and look on ebay
@projekt_no42 ай бұрын
Hi! Had the cables replaced by a workshop (came in with a complete new engine btw..😂) and now the shifting is a bit “off” - I get 3rd gear instead of 5th, 2nd instead of 4th etc. Feels like the gear selector is a bit too much to the left or whatever. Do you think that’s what I can adjust with the orange clip? Would be great cause this really sucks 😂
@fuelheadjay88002 ай бұрын
Yes should be able to
@TheKinlock2 жыл бұрын
Hi Jay that was really helpful, could you let me know where you ordered your cables from? I got the smaller ones and can’t find the longer ones, great footage thanks
@TheKinlock2 жыл бұрын
Hi Jay that was a great help, who did you buy the cables from? I have made the same mistake in getting the smaller ones. Thanks for the vid
@fuelheadjay88002 жыл бұрын
Type this number in ebay search 255138011598 Glad to help
@kevherman9437 Жыл бұрын
Did you take the orange clip off on the longest cable right hand as sat in cab, I can’t get reverse with new cables 🤷♂️🤷♂️
@fuelheadjay8800 Жыл бұрын
Orange clip adjusts stick pull clip out and you can adjust the rod up and down sound like yours is adjusted to tight that's y u cannot get reverse pull clip out pull rod down to knotchs the put clip back in hope you get me 😂
@kevherman9437 Жыл бұрын
Thank you for quick reply 👍👍👍👍👍
@kevherman9437 Жыл бұрын
All sorted jay thank you
@florianzavada41852 жыл бұрын
Super!!
@PeterSmith-sp7nb2 жыл бұрын
Hi Jay, thanks for the video. Did replacing the cables solve the issue. Can anything else be done besides changing the gearbox. Cheers Pete
@fuelheadjay88002 жыл бұрын
It did for around 40 mile but I've lost all bottom gears so at mo I'm striping box off to see what's wrong vid Will be coming out soon
@PeterSmith-sp7nb2 жыл бұрын
@@fuelheadjay8800 🙁
@AldaynJackson22 күн бұрын
Model 2006 Renault Megane
@SP330Y9 ай бұрын
Before you changed the cables was it very difficult to get in gear?, mine is like that feels like the gears resist trying to go in easily, after changing cables did it then go into gear easily
@fuelheadjay88009 ай бұрын
Yes mate a lot easy
@Sam-ic2bp Жыл бұрын
Hi are the longer and short for the swb and lwb?
@fuelheadjay8800 Жыл бұрын
I don't think so the best thing to do is take off and measure as was told two different sizes for my year van not sure way unless rerouted different but first one was too small I got may be has mine a mwb.
@whiteeedotcom Жыл бұрын
If it’s the same as a traffic (vivaro etc) the cable ties hold the linkage on to gearbox end (the ball joint gets loose) and there’s an aftermarket solution instead of cable ties that’s cheap on eBay. Not sure about the rest of the cable ties though