433Mhz Garage Door Opener - Universal Remote - Easy How to Program

[@martinmcgettigan9216]

That worked like a dream.... I went in with LOW expectations but following your clear instructions it worked first time.... Possibly for the first time ever..... Thank you very much 👍

[@PaulBeausang]

Tried 3 different videos - the approach shown here was the one which worked for me. Note that the approach was different from the instructions provided with the remote. Video is really clear and specific on steps needed and how you know the programming is working - i.e. what LEDs flash and when. Really useful - many thanks

[@rent2ownnz]

Appreciate the feed back, am really glad it worked for you. Took me a long time to figure it out by trial and error.

[@skunk_workx]

Best video for getting these remotes working, thank you.

[@opsahle2]

Thank you so much! I managed to get an universal remote from Aliexpress (not the one you show here) up and running thanks to your video. But strangely: All four buttons seem to be programmed now, but only one is doing anything - and it is NOT the one I pressed during the cloning process. But the main thing is that I now have a working clone!

[@rachaelmoore3673]

Perfect - worked first time with my NECo key fob. Saved myself £40 😀

[@rent2ownnz]

Nice one! good stuff :)

[@alfilart]

I watched many videos and this is the one that works. Thanks!

[@sticustom]

Thanks mate. You made my life a lot easier. Just read the instructions and they made no sense at all. I got the remote to work as I watched your video 👍🏻

[@csikiandris]

Köszönjük!

[@headgon]

Hay any tips I did what you did it didn't work so tried to program of the main unit but that didn't work either maybe duds?

[@rent2ownnz]

Not sure ... have a look at some of the previous comments there are a few methods to do these units.

[@johnsgalv]

Thanks man, finally got the bloody thing running 😀

[@matarankamataranka9257]

Lorsque je veux réinitialiser la télécommande en appuyant sur les touches A et B ==> la lumière reste fixe. Y-a-t-il une autre possibilité de réinitialisation?

[@rent2ownnz]

je ne suis pas sûr. Je n'ai pas eu ce problème. Je pense avoir posté un autre lien dans la description pour une autre méthode que j'ai trouvée. Cela peut vous aider.

[@hrcivic]

The best easiest tutorial i ever seen. Thank you very much

[@denis8321]

Is there any possibility to erase the code from the original remote when programming a new remote? I have only one original, and I don't know how to reprogram again if needed. 🙄

[@eutherian]

Cheers. This has saved me twice!

[@beeldbuijs1003]

Thanks. Two additional tips: Mine would stil not open the garage door, despite the led blinking confirmation. Turned out there was a tiny piece of bare metal wire broken loose from the solder on one side, on the back of the new remote. I soldered it back and now it works fine! I had to 'tune' to the right frequency by turning the tiny screw on the bottom right first though. :)

[@simonkirton8521]

Just wondering before I pull my elderly neighbours remote apart can you actually change the frequency on these remotes if that’s what I take ‘tune’ as or you just having a laugh

[@LegendLength]

@@simonkirton8521 I believe they support 2 freqencies, 430 and 320 or something like that. So it's likely some kind of binary switch.

[@Araian85]

Thank you. Mine came without instructions. Works perfectly now.

[@rent2ownnz]

You're welcome!

[@Outdoorsy_86]

Only video that worked for me👍🏻 thank you 🙌

[@paulsgreatdane]

Great video mate! I followed the instructions that came with the remote and it didn't work. lots of looking around before I came across your that works cheers 🇬🇧

[@brianpeterson113]

Thank you. I never got a manual when I purchased these. This video is very helpful and they work great. Thank you for the 411.

[@rent2ownnz]

Most welcome

[@JL-dg8ym]

The best and simplest instruction - thank you thank you😊

[@jeso317]

Great vid, mine works great. Would you consider a video on how to change the battery on this badboy?

[@SonjaBrODNJAK]

Thank you very much... With your explanation works excellent...You saved a lot of time... I am very grateful....

[@rent2ownnz]

Thanks. Yes it took me along time to figure it out myself. Back when I sorted this, there was not one solution. Glad this helps people :) hopes you liked and subbed to push it back up the list :)

[@nothere9551]

I got a couple I had trouble programming them too. After a year still going strong.

[@kidda74]

Got mine to work thanks to your video, but the range on it is crap. I have to be almost on top of the garage door mechanism for it to work? The original one still works from metres away?

[@rent2ownnz]

faulty remote

[@saskiajonker9247]

Thanks for this, instructions were vague but got the remote to work thanks to your video!

[@keZZaZ84]

All well and good if it flashes 3 times but what about when the light just flashes rapidly when pushing A and B

[@shaun.oo__oo]

Champion, I was following OEM instructions and nothing was working till I saw your video and cleared the remote. Followed OEM instructions again and boom... working remote 👍

[@rent2ownnz]

Great ... MAybe you should share you one that was not working here and I will add it into my intro speel above, may work for the ones that my method does not work

[@shaun.oo__oo]

@@rent2ownnz I didn't make a video mate, all good your video was what I needed to do 👍

[@DavidJohnston58]

Thanks, that got it going. But A would only open the door so programmed C straight after in same way and now A opens and C closes, I'm happy with that.👌

[@rent2ownnz]

Cheers. Maybe your door master controller memory is full. you can clear it and start from scratch. should work. KZbin it :) I think I did a video years ago that had how to reset and clear the master controller memory.

[@0017397]

what if the LED doesn't flash when I press and hold both A&B?

[@imflamez5940]

^^^

[@declanjoyce8640]

Yep...this works, just ended 6 months of faffing about with other remotes...(but there again I am a slow learner!)

[@rent2ownnz]

Lol, life is about learning. pay it forward :) Glad it worked for you

[@ggazzara1115]

Thanks for posting a video that actually works for these remotes! I really appreciate all of the research that you did to figure this out too.

[@rent2ownnz]

Thanks for the review. I am happy it worked for you. CHEERS WESTY!

[@rorybrennan6828]

Loving the content westy!

[@rent2ownnz]

Thanks my man

[@binyuan9645]

Mine looks like the same but doesn’t do the three blinks and I wonder how to make it work.😢

[@rent2ownnz]

You Tube it. I believe there are or 3 different methods for the same looking device. If you do find it, let me know and I will post it in the title notes. and may even add a little bit of an explanation at the end of this video.

[@abbcyuan4525]

@@rent2ownnz Thanks for reply. I did have searched and watched more KZbins but no luck yet with those not blinking like mine.

[@shabanah8027]

On the larger remote which is the button to close the door?

[@rent2ownnz]

the biggest button

[@shabanah8027]

@@rent2ownnz but that's the button that opens it for me. It doesn't close it

[@viewer6825]

Hi mate..thanks for the video, as my same remotes are crazy.I followed yur reset ode, howeer, theywill no reset. I get th same led light flashes like you do, but they never reset....any more clu?

[@rent2ownnz]

Hi, Have you tried following the instructions in the description? I have linked 2 other videos that may help at the top as well you you.

[@rent2ownnz]

Hi - you could try the description notes and I have also 2 other you tube links that may work to help you out.

[@viewer6825]

Please, yes for extra links. I have followed the tutorial exactly. The broblem that keeps reoccurring, is when actually holding down the original remote button and the clone one. When simultaneously pressed, I get the clone led flash a few times, but it will never do the final flash to say it has accepted the code Unfortunately, this same thing happens every time. I do hold the remotes next to each other, and have rotated the original remote to every single side, as well as to the two faces of the remote to try find the signal, all to no avail.The clone resets perfectly, as shown by pressing a/button at same time, and then releasing b 3 times. It will simply not indicate the led flash that the code has been read. Thanks

[@viewer6825]

Well, after months of trying, I cannot get these to work on a Firmamatic remote controlled garage door. I still find, that on some occasions, it appears, like the video, that the buttons do not have anything stored. However, a long press of the buttons, which is needed to get my control unit to recognise the transmitting remote, that all the a b c d buttons all show a red light on a long press, and not on with a quick press. I tried so many times, I got the remote batteries go flat. Tried on three units as per the video, without luck. Does anyone use them on anything else, so I can try to confirm they are simply not compatible with Firmamatic?? Thanks for the help.

[@rodneybradbury2880]

Hi Westy i tried everything you have in the video but still not work i have a merlin garage door any other ideas i could try thanks Rod.

[@rent2ownnz]

Hi Rod, is it the correct frequency remote for the door itself?

[@Msopasniful]

Hi all, i cant erase function. Press a and b together but dont stop blinking. Is there any solutions?

[@dianazamfirescu359]

Hi. My remote is continuously flashing and no combination of keys can stop this. Do you know what i can do?

[@AEROSOLKID1]

Yo!! Like the video but HTF do you get 'em cleared of factory code? I have tried pressing A & B simultaneously but the light just continously lights intermittently.

[@joriiiiii]

Same problem here, still looking for a solution...

[@IIIMrReaperIII]

But how do I program the remote i have but only one buton, I dont wanna lose any other i already have programed ?

[@jonnolee667]

Great demo mate, unfortunately my remotes just keeps flashing red rapidly when I press A and B

[@rent2ownnz]

There are a few ways to do it... See if you can you tube another method.

[@LegendLength]

My problem was not pressing them at exactly the same time.

[@Wen-hz9mb]

I’ve tried this Di many times! When I press a & b together the led just flashes fast ..what am I doing wrong? 😩

[@LegendLength]

@@Wen-hz9mb again, press the *exact* same time

[@waltermelon5672]

Thanks so much. Lifesaver ! In my case I only got one to work. The other would not reset . The button solid Flash after reset on every button . Edit : got it to work. Must be something about the timing issue with resetting

[@rent2ownnz]

must be kaput ... probably a broken wire

[@balthazarixe3542]

The duplicate remote programmed using your video was perfect. However it works only 1 time and then has to be re programmed and process repeated. Any solution for this ?

[@rent2ownnz]

Hard reboot and then clear off any memory on the garage door controller itself. Then try it.

[@balthazarixe3542]

@@rent2ownnz thanks for this. However it works for the first time I press the cloned remote . Should I try pressing again, it does not work. If it works once it has to keep working. Could it be that it’s not able to store memory

[@christianreiss7203]

I have same problem. I thought remote was broken so I bought few of them from diffrent producers but still works only once. I tried to code it in motor but still works only once😐

[@maddhouse5324]

Hey. When I follow the first step to clear codes. I hold A+B, (3x Flash) release B, press B x3 and nothing happens. Any ideas?

[@Baifundo]

Same issue here!

[@rachaelsteele4364]

Have you solved this as I'm having the same issue...

[@maddhouse5324]

Unfortunately, I did not. After following the manufacturers programming method and also every other tutorial on the internet, I ended up getting refunded from ebay. Sorry I couldnt be any help. Good luck. :)

[@mightymouse6293]

How would you know if your remote device is 315mhz, 433mhz or 330 mhz?

[@rent2ownnz]

written on it. or on the the inside (Normally a sticker) or you can get a frequency scanner and press a button and see what frequency it is emitting.

[@robbyhiggins]

Worked perfectly, Thankyou

[@patrycjaradecka950]

Hi, not sure if someone has the same issue. I have the same garage fob, but a few weeks after programming it's not working and I have to do the programming again. I even bought two and they both lost programming at the same time. Does anyone know what could be the reason?

[@applebeetea9301]

Could you make a tutorial to replace the batteries for this exact model? Thank you

[@rent2ownnz]

Hi There, Which model? the old one? or the new one?

[@johnruru2706]

Cheers mate for your help. Good video, great help👍👍

[@charliedrake247]

Great job thank you for your help.😊

[@vspeaight]

Thanks for the great and easy to follow video. Set mine up in minutes after watching your video. Works so well. Thanks for taking the trouble to make this very helpful video. Australia

[@rent2ownnz]

More than welcome. Glad it helped.

[@nekonekad3573]

Hallo Westy Sehr geehrter Herr Ich habe 4 gleiche Schlüssel kekauft und jetzt habe ich ein Problem, ich kann die Fernbedienungen nicht programmieren. Ich muss zuerst den Speicher löschen, damit ich dasselbe programmieren kann. Wenn ich jedoch z. A- und B-Taste gleichzeitig geht das Licht sofort an und brennt ohne Unterbrechung, obwohl ich die csk-Tasten bis zu 20 Sekunden lang gedrückt halte. Gibt es einen anderen Weg, was soll ich tun, bitte erklären. Grüße aus Österreich

[@nekonekad3573]

Dear Sir, I bought 4 of the same keysI have a problem, I cannot program the remote controls. I have to clear the memory first so I can program the same thing. However, if I z. A and B button at the same time the light goes on immediately and stays on without interruption, even though I keep the csk buttons pressed for up to 20 seconds. Is there any other way what should i do please explain. greetings from Austria

[@samanthastubberfield8975]

I followed all instructions and it shows that my remote is linked. But still doesnt open garage. Have tried doing it on the actual garage door as last part instructed. Flashes as if synced. But still doesnt work 2 open garage :( please help.

[@logankelsall6389]

Is it the same process for a gate remote to.

[@ASousaMakesIt]

Thank you! I just did it and worked like a charm!

[@rent2ownnz]

I am glad.... Yep I struggled to find the way to do it ... so figured it out and shared it so you all can get the benefit. hope you liked and subscribed

[@SenorNav]

Thank you sir, your method worked great in New Zealand. Jai hind

[@jonatanpagdanganan]

The problem is when you are in 30meters away to your door the clone remote did not work

[@rent2ownnz]

get a genuine one then as your signal strength sounds like it has reached it range. easiest way to find your range is to slowly walk toward the door and press until the door reacts.

[@insaf2668]

I got a Morton 10 by alpan garage door , will it work for it?

[@rent2ownnz]

Not sure... Only one way to find out.

[@christianreiss7203]

Hi maybe someone know how to solve my problem. I have the same universal remote but after copying the code it works only once and after that one shot it stops working. I tried few other remotes and same story.

[@rent2ownnz]

i would say you may need to clear you main controller memory

[@zeuline1]

I did all the same. Reset, clone. Lights the same blink, after clone steady on on press, but remote doing nothing. On old remote the same MHZ 433,92. Where can be trick?

[@giannisk7658]

Thanks a lot brother from greece

[@rent2ownnz]

No problem😉

[@sharky9901]

Hey man, just bought a couple but when trying to clear them, the led on both of the clone remotes constantly flashes and I’m unable to clear or sync them up, any idea how to fix this?

[@archonpropertiescrete]

Same problem here

[@jondost7592]

Same to me , did you find where’s problem?

[@scottellis4785]

Hi there, I seem to be having issues with teh second part "go into the garage door operation unit and put it into learning mode, then once you have done that press the button and booyah!" How do I put the door unit into learning mode?

[@ishbhad]

On the back of the box unit which hangs on the ceiling of your garage door you’ll see a button which says” learn” . That’s what he is talking about

[@stevejones4254]

I'm getting the light flash for 1 button but it's not connecting to door🤔 Ant thoughts anyone?

[@rent2ownnz]

If you read the instructions in the description, you will get your answer :)

[@stevejones4254]

@@rent2ownnz it's not pairing with the door

[@Sorjen108]

Can someone help please I have pressed both button which did the reset I have clone 1st and 2nd button from the original remote, which worked My first try with the gate was a success, both opening and closing However this was the first and last time it worked, the remote still works, blue light still flashes upon press, but the gate do not respond at all PS:The original remote is still working normally Thank you

[@kimpyne1972]

Hi. I have that exact remote just arrived. I press both A and B buttons together. I get one quick light then a constant flickering light. Not 3 lights then off. Any ideas that I could try? Cheers.

[@rent2ownnz]

you could try this kzbin.info/www/bejne/ol7OkIusoL9joKc

[@rent2ownnz]

or this kzbin.info/www/bejne/iH7CqZqEqLVnqbM

[@ArthurvdHorst]

Really happy I came accross your video but this still didn't work for me as my garage control unit does not recognize the new remote. Which is the same remote as the one you have. Also my garage opener is a Chamberlain but guess a different model from yours. I got a ML500. Any suggestions or is it perhaps that this remote will simply not work for this model?

[@rent2ownnz]

Hi There, Try doing to the Door opening controller (On the door itself) and press your buttons on the remote.... can you see the light rapidly flashing on the control unit? if so, it is seeing your remote , but just needs to be #CODED# into your controller. try the last part of my instruction on how to do that. - see how you go

[@ArthurvdHorst]

Westy's How To Guides Thank you for your reply. I have noticed that when I use the original remote the LED on the control unit flashes rapidly but it does not flash rapidly when using the new remote. I guess that answers my question then, the control unit does not see the remote. Will have to look into another model.

[@corkfella]

Super work brother . Saved me a tonne of time. Big ups from Ireland 🇮🇪

[@rent2ownnz]

Great, glad it helped you out.

[@imtheboss8414]

Can i program the RC like when i press A to open when i press B to close ?

[@rctrix9063]

Yep Nar, the clear out bit works but the learning bit was a flop.

[@q4qatar921]

It helps me alot 😍😍😍

[@GrimmReaper7165]

I saw another vid that showed how to clear out the program but it didn't work. Yours did! Thank you so much!

[@rent2ownnz]

glad it helped you out

[@raulbzr]

It helps , but i must see this video for several times , because I can not understand British accent. 😬

[@rent2ownnz]

It is a New Zealand Accent ... Thank you kindly :)

[@civramatt]

Thanks this really helped and it worked perfectly.

[@Christian-jf5ys]

I have the same original remote and same code clone key and it did not work for me

[@kurtbruns8102]

Tried it step by step but still can't stop all lights flashing? Any idea Why?

[@sophiedavies7621]

When I press and hold a and b I get a continuous red light!

[@Ioxna]

When I hold down both buttons it stays solid. Nothing I've tried makes it blink.

[@rent2ownnz]

Steps: ================================ |Clear existing Memory Settings| ================================ 1. Hold down the A & B Button (the two closest to the LED Light) 2. While Holding down Button A (Left) Press (Slowly) button B -right one, 3 times 3. Then Release Button A. Now no button presses will operate the light (LED) ================================ |How to Set New Learning Code | ================================ This is a 2 Stage Process: ========= |STAGE 1| Programming New REMOTE ========= 1. Get old door opener and the new non-programmed one close to each other 2. One the old Remote that works, hold down the button that works on the door 3. Now Press and hold the button (The LED will Flash a few times and then be raon the new remote you wish to operate your door with. 4. Hold this button down until the LED light goes Solid 5. Stage one Complete ========= |STAGE 2| Syncing to Door Master Controller (If Above does not work) ========= 1. Put Garage Door Master Controller into learning mode and wait till it is in listening mode (Each type is different = refer to your owners manual) and then press the button you have configured.

[@olivierdescargues]

thanks . had the same problem . remote has been laying in the car for 6 months . now working thanks to you. cheers

[@coolguyindeed]

Same.. I have mine for years. Until now i really need it for my remote car replacement. The instruction to clear the code is different from other videos i've found years ago. Once again, thank you sir westy 👍

[@Maraxion]

Hi Westy. It seems you have done some research and in fact it worked on another remote I had with a different look to it. But I do have an identical to yours I cannot seem to get to work. When I press each button a single red blink comes. When I press and hold A+B it firsts glows red, then starts to blink fast. But all 4 stil blinks when pressing. If I hold C+D then It again glows red and fast flashing, but after that all 4 buttons seems to have code... Its whery strange! If I then try to copy, its starts flashing like crazy when there is a signal(not when there isent), but it still doessent work afterwards... Almost like the sender is dead.

[@rent2ownnz]

kzbin.info/www/bejne/iH7CqZqEqLVnqbM

[@Maraxion]

Thanks. iv tried that before. But I cannot seem to get it to go 100% dark. Its either coded with continiously blinking, or just 1 blink when pressing a button :)

[@photisdaskalakis7602]

i got the same problem.every button flashes 1 time and goes off. i try reset A+B or C+D and blink continuisly. not 3 times.

[@markod]

same here

[@snooker0144]

same

[@emiliomota2459]

You really helped me out man

[@rent2ownnz]

You are more than welcome. Glad it worked for ya

[@Willhell]

but what do i do when I have lost the remote control, and i can't copy the signal to the new remote...?

[@thetrue1master]

William Helle I try a next way and Its works . Press and hold button 1 then press button 2 4x. REd light should be blinking. Press your remote then the clone remote should change blink faster press on the clone button you want to be clone

[@anpexroblox3371]

Dose it work on all Merlin garage door remotes?

[@Mullins117]

Rezeriv Fun time Yes it does

[@byjingobob]

Cheers Westy, I was getting close to the end of my rope! Now working perfectly thanks to your video.

[@bizrhapsody]

I can’t make mine work no mater how hard I tried to clear the code from the original setting and it still flashes when I press any of these buttons. It is rather very easy to sync from the original remote control unit with the master control unit. Any ideas how to make it work?

[@rent2ownnz]

Sorry to hear that... You might have to search for another way to do it There are a few different ways

[@bizrhapsody]

Westy's How To Guides wow, thanks for your reply and I never expected that! My units have blue led signals and after I cleared the original setups, those buttons still can flash once when they were pressed. How bazaar?! I do realise my original Napoleon garage door opener is in 303hz however those new remote control units I purchased from eBay is up to 433hz, would there be any difference? I’m really confused now…haha

[@ants960]

Mine just drains the new battery as soon as I install it works for a Lil bit then the light gets week then goes out

[@morp3th_929]

What do you do if the original remote is broken?

[@stevel8964]

you have to use the program button on the garage door motor

[@snooker0144]

When i press A+B the red light just keeps flashing really fast; all buttons are programmed so i cant reset it because it keeps flashing really fast 1

[@FA_vortex]

I have the same problem, anyone know a solution?

[@oikarinte]

Same problem here! Anyone?

[@edwinmv1610]

yeah same here mate... cant seem to find a solution

[@livingalpujarras]

I push and A and B together and get the flashing lights and then B slowly 3 times and it doesn’t work. Any ideas?

[@4snday]

Living Alpujarras that’s what I get and I’ve tried different ways and still nothing.

[@livingalpujarras]

Maybe the one that we are trying to copy is a different frequency

[@4snday]

Living Alpujarras same frequency.

[@gio_anvi]

Hi, I did it but when I press the button to open the garage is not working, you said something at the end but I didn’t understand, something with the motor? I did the same with a car remote control and works, but I’m not sure why with the garage is not working

[@mishjames]

I had two remotes for this model one was stolen out of my car, if I follow the guide above, and reset the existing remote, will the stolen remote still work ?

[@rent2ownnz]

Hi Michelle, Very ... very good question. What you can to is clear all the previous saved configs in your door controller. then add your new ones! that should solve your problem.

[@digger5521]

Will this work if I don't have old remote it's missing it's a b&d roller door pretty old school mate

[@rent2ownnz]

Open your B & D MAin Module in your garage and see if it has the frequency on it ... should be 433Mhz if not ... get which frequency it is and then get on online and follow the same set up. you will be able to clear all previous paired coeds and set a new one. Look up your model specs online and you should find a manual that works.

[@edamamebiru3960]

Thanks for the video. If I don't have the remote, can I buy one on eBay and ask the owner of the garage door the provide me with the frequency and a code? But, then, how could I program myself the remote? Sorry, lots of questions.

[@xray364]

Hi, anyone know what to do when the key doesn't reset properly. I've got a 3 button which is exactly the same. I programmed it ages ago and I wanted to reset it but I forgot the instructions. I thought it would be the same process by no luck unfortunately. BTW, when I open the key to reveal board and battery, it actually has 4 programmable button, but only three on the outside. Not sure why they hid one of them

[@Goofball694]

What if you broke your original garage door remote. How do I program the universal garage door opener without the old remote?

[@rent2ownnz]

Try Using the Stage 2 from my method above.

[@seanp4700]

mate the last part of your vid is exactly what im looking for. But I didn't quite get what you mean. I seemed to have copied the program onto my universal key but it didn't work on the door. Does the last part of your vid mean that I should do the clone process close to the operation unit? or putting the operation unit under learning mode? really appreciate if you can clarify on that!

[@rent2ownnz]

"Does the last part of your vid mean that I should do the clone process close to the operation unit? or putting the operation unit under learning mode? really appreciate if you can clarify on that! " Look up your Garage door control unit manual and work out how you put it into learning mode. Once in the mode. Press your new remote that you programmed in my above video and Viola!

[@rent2ownnz]

Press and hold DOOR CODE button once Select one of the four buttons on key transmitter you wish to use to control the door. Or the button on the end of the manual release cord. Setting the Transmitter to Operate the Door The opener can only operate from transmitters that have been programmed into its receiver. The receiver needs to learn the codes of any transmitter that will be used with the operator. Up to sixty four (64) codes can be stored in the receiver’s memory. a. Ensure the button cover has been removed (see Electrocution caution) and the opener is turned on. b. Press and hold the DOOR CODE button. The DOOR CODE LED will illuminate and beep to indicate the opener is in Code Learn mode (Fig. 8.1). c. Press and hold the transmitter button that you want to control the door for two (2) seconds, pause for two (2) seconds, then press the same button again for two (2) seconds and release. d. Release the DOOR CODE button. e. Press the transmitter button to test.

[@seanp4700]

thanks dude. really appreciate your detailed explanation. it will defs help other people stuck in a similar situation. but i guess im done cuz its a gate for the entire flat's parking area. i just moved in and i thought i could just copy my flatmate's key but if i open that control unit chances are i get taken by the police... but anyway really useful content keep it up fam

[@farasatali2646]

WHEN I PUSH A&B NO FLASHING LIGHT COMMING.PLEASE.

[@VenomHadesOfficial]

When i press A+B the red light just keeps flashing really fast; all buttons are programmed so i cant reset it because it keeps flashing really fast

[@chengzhu7168]

Venom Hades I got same issue

[@livingalpujarras]

Me too

[@jondost7592]

Did you fix it , I have same problem.

[@VenomHadesOfficial]

Jon Dost nah never worked just scrapped it

[@oompa_loompa5943]

Bloody legend mate❤️

[@mailantrinh9623]

Thank you for your instruction. My remote finally works now 👍