Replace Backlight LEDs on Samsung Curved 55” for $30 (UN55NU7300 / UN55NU7100 dim screen)

[@EdwardInTX]

IMPORTANT NOTE: On the burned plexiglass at 5:19, it's best to sand down / dremel the burned areas until they're gone, and then reinstall it into the TV the same way. If you do not dremel down the burned areas, TV will appear yellow like at 9:11. The way the plexiglass is made, it's supposed to darken the section closest to the LED and brighten the section away from the LED. Do NOT flip the plexiglass. 1. TV LEDs can be purchased here! ebay.us/KQqhgg 2. Screwdriver set: amzn.to/2OiNf6v 3. Plastic Putty Knife: amzn.to/3rfUGtQ 4. LED Lights: ebay.us/scXAT3 OR amzn.to/4du9nBz

[@kriswingert1662]

I have the UN55HU7200F ( not the NU in the middle like yours ), same backlight as in yours or is it a full array?

[@EdwardInTX]

@@kriswingert1662 HU has many more backlights www.ebay.com/itm/203105953105

[@kx5e]

@@EdwardInTX I have the Samsung UN55NU7300FXZA. As with your's in the video, my plexiglass is cracked and the inner white panel next to it had LED heat damage. Smelled, LOL!!! I got it fixed and it is watchable but the cracks and heat damage do show on the bottom. Can those parts be found at a reasonable cost. Now that I know how, it'd be an easier task. Best advice I can give to others about doing your own repair is to have and use patience and a small and thin straight blade screw driver to remove the white inner frame and twist at the tabs just enough to clear the lock points. My only left over parts were the few I broke and then thought about the smaller screw driver and that worked. But I also slowed down the process. Great video. Thanks Edward.

[@DAW-GUN]

You really oughta add to the video itself about this. No one is going to look at the comments until after they have problems from following your advice. You can add audio, video or just captions but you're garnering a lot of ill will by leaving it up as is.

[@vladislavcvetanov5882]

When you dremel down the burned areas won't the LEDs be too far from the plexiglass and won't it interfere with the TV's performance

[@MohammedAneek]

Thanks a lot for you and all the other youtubers. I managed to watch these videos and fix my TV for just 1/10th of the repair cost.

[@drsnooz8112]

I so appreciate when others risk breaking their stuff to show me how not to. Thank you!

[@muntariyakubu8821]

I took mine for repairs and they told me it’s the screen so I returned it back home… Thank you very much 🙏 now I can fix mine💪🙏🙏

[@Taminara]

We followed your guide and were able to fix the tv so that it was watchable again but it was far more difficult for us noobs than it seemed in the video. Many of the little plastic tabs broke and a small chunk of the bezel broke, etc. The one issue that we have now is that when we turned it back on and could see the screen, the picture looks like its being viewed on say.. something like cardboard or some other sort of material and on the far right side, there's an inch where the picture stops instead of going to full side. We obviously messed something up in putting it back together and the two that helped aren't interested in repeating the pull apart process because it was such a hassle for us. No matter what though, the good news is that the process you demonstrated worked and we can now see the full screen. Whatever caused the other issues was something we somehow did. Thank you for the video.

[@kerokerohim]

Fixed the family TV and saved 70% of the TV's cost (what their asking for repairs) THANKS!!!

[@ciaranburke1104]

Few tips for anybody giving it a go: 1) when you get to remove the LCD panel I found if you very carefully slide a bed sheet) or something similar) under the panel you can easily slide the panel from the base without damaging it. 2) tape the 2 white sheets under the (LCD Panel) together so you don’t lose their orientation/order. 3)do the same for the plexiglass and white backing as it is KEY this goes in the correct way or light will not amit correctly. 4) make sure the white frame clips securing the felxiglass are fixed in correctly. (I made this mistake and I had a lot of LED bleed along the bottom edge just from 2 clips not in correctly) 5) if you put it all back together and the bottom of the screen is very light and top very dim. Your Felxiglass is upside down. Unfortunately you have to take it all apart again and turn it so the top edge is at the bottom. Trust me it a lot easier to take apart the second time. ( you can also plug the tv in with just the plexiglass clipped in to see if the light is covering the entire panel. Instead of reassembling the whole tv to find it's not). But Thanks Man what a helpful video! Wouldn’t have tried doing this myself if I didn’t watch it and now have a good as new working TV!

[@EdwardInTX]

Excellent tips!

[@theri0n]

I'm having the opposite effect of the bottom portion being bright but the the middle and top being very dim.

[@PEWti]

The sheet thing is amazing advice. Was gonna order suction cups and my wife said- what if it straightens out your lcd

[@nunyabidness1888]

I used your tutorial on my flat screen Samsung UN50NU7200. The components are exactly the same, except it doesn't have the white tabs securing the metal strip. Unfortunately, I hadn't read your comment about the plexiglass orientation and that dark-on-bottom/light-on-top thing, so I'll be re-doing it tomorrow. For now, the light strips are working great. Thank you so very much for a great video!

[@EdwardInTX]

Awesome! Hope the reinstall goes well!

[@djhellspun]

This walkthru guided me thru the entire process on a 7100fxza that was given to me for free! It is working good as new! 🙌🙏 Thank you SO much!

[@EdwardInTX]

woohoo!

[@alihamdan4478]

Thanks Edward you are so kind for sharing this with the public saving us lots of money 🙏

[@tecc8380]

I did this repair and everything went well following your instructions. I also had a crack in my plexiglass but unfortunately flipping it around created a big shadowed area in upper portion of the screen. Just had to install it the way it was and all is well!! Thank you very much for this video!! 👏🙏

[@EdwardInTX]

Awesome!!

[@StAlKeRrEpAcK]

Because maybe yours contain mirror sheet and u didnt flip the mirror sheet that reflect light some of those have this type of sheet that u must flip them

[@tecc8380]

@@StAlKeRrEpAcK Things woodworkers don't know! 🤣 Thanks for the solid info.

[@StAlKeRrEpAcK]

@@tecc8380 im a mechanic but i know basic electronics

[@tecc8380]

@@StAlKeRrEpAcK So you are gonna use your "intelligence" to generate a negative vibration and judge your own kind? You are aware that people know different things, right?

[@crzprgrmmr]

Hey, thanks a lot for the guide. Based on your video I successfully repaired slightly different model (6 series instead of 7). While there were some differences your video was a great start. Now I just hope those "original" led strips from AliExpress won't die after 2 weeks

[@EdwardInTX]

Very nice! I've done a handful of 6 series the same way!

[@mrpash7075]

Hi, i just want to say thank you for the video. It was perfect to follow. Ive replaced LEDs on my TV and saved myself £££ buying new one. Only cost me a £10 for 2 LEDs strips from Ali Express. Bonus! Thanks again.

[@EdwardInTX]

awesome!!

[@koor23]

Thanks for the useful video. Fixed mine 55" in 45 minutes. Big up 👍

[@EdwardInTX]

Nice!!!

[@michaelstark9939]

Was it the same model he did in the video??

[@koor23]

@@michaelstark9939 Mine was UA55NU7090 .

[@Razi3l89]

i have an old tv i wasnt able to open, while not the same model was similar enough to be guided by this video! thanks a lot!

[@EdwardInTX]

@@Razi3l89 awesome!

[@DiamondD904]

This was a good video. I have the same problem with my backlight in my UN48js9000f. I’m gonna attempt your method. Pray for me

[@EdwardInTX]

good luck!

[@jamienwright7337]

Fixed mine with no problem. Thanks for the video bro 💯💪🏿

[@ilovecubes8598]

Great video. I have one now that needs the repair. Could I put do anything such as adding thermal paste to help prevent over heating again?

[@EdwardInTX]

Some people mention adding a capacitor to regulate the LEDs but I’m not that advanced

[@mrcreeperman13]

@@EdwardInTX i have the same problem on my samsung.. Really refuse to send it back for repairs for hundreds of dollars so i might try it myself I’m just wondering how old was this particular tv? Screens nowadays seem to last like a year or 2 until they get this Great video though!

[@EdwardInTX]

@@mrcreeperman13 this was either 2017 or 2018. It was the 4th 7 series samsung I fixed.

[@mildreyortiz8725]

Richard Dolesh una pregunta este tv trae salida de Bluetooth ?

[@SnappyMcCrappy]

Thanks very much, I used this video to fix my own issue, sadly, as careful as I tried to be I cracked the screen. Knew it was over but decided to carry on anyway. Anyone thinking about doing this, please be so careful. I barely moved the screen and it cracked. On the bright side I've just ordered a 70 inch ambient light Philips. 😁

[@fidelbanuelos9601]

This is why I am having a professional fix my TV. I would break something if I tried to do it.

[@Beast-mf7br]

@@fidelbanuelos9601 buy two suction cup thingys and its easy...my dumbass cousin lifted the corner as I was unpacking my suction cups and cracked the fuck out of my top left corner almost to the top middle of the screen...so other than that it's surprisingly easy to do in less than an hour, just use suction on the main screen

[@crzprgrmmr]

​@@Beast-mf7br I used paper packing tape instead of suction cups- worked great and left no glue marks

[@smartgui37]

it is great to watch this one even a fresher can do this thanks for the well narrated video....

[@EdwardInTX]

Thank you!

[@gameovered777]

Did repositioning that paper help with the back light bleed? I have the same issue after replacing the LEDs. I hate opening up this TV lol

[@EdwardInTX]

The burnt panel had to be installed the same way it came out. Can't flip it. The trick with that panel is the burned areas need to be completely dremeled off.

[@coding_bean]

Can I use this process if the screen is not functioning?

[@RobbazCorgiPikaPikaMadaFaka]

I really wish you showed how to safely move the lcd panel instead of transition to it being done. My brother and I were on the last step of moving the lcd panel back in place with a team lift, only for the screen to crack in the same corner I replaced the broken leds. Now instead of half a screen being black, I have about %96 a screen with a crack in the corner. How did you move the lcd panel multiple times as one guy without cracking it?

[@MrBwins]

Exactly. My new LEDs are working great, but now the tv is trash because somehow I got a crack through the screen. Tv is trash. I was trying to be so careful and didn't even realize I got crack until I got it all put back together and turned it back on.

[@AnyManProjects]

Excellent Video! Thank you for posting!! Let me ask you this.... Why is it that just about everything Samsung makes, turns out to be absolute crap!?? We purchased all new higher end Samsung black stainless appliances in 2018. In the first year the microwave failed twice. The oven part of the range failed twice, the fridge ice maker froze over daily and stopped producing ice. The metal finish is so thin that it dents with almost no pressure. Now our 2 year old 75" OLED backlight has failed on the right side. I WILL NEVER BUY ANOTHER SAMSUNG PRODUCT EVER AGAIN.

[@EdwardInTX]

Wow this is terrible! I have a samsung microwave and range and they haven't failed (knock on wood)

[@neilrsingh01]

Hi, just came across your video, it's brilliant this is what i was looking for it was a BIG help thanks .

[@EdwardInTX]

awesome!

[@bgg]

Fantastic video - thanks! My son and I had a great afternoon project and the TV is working beautifully. Had a minor panic when we turned it on and the screen was black. Realised we hadn’t connected the ribbon cables correctly so pulled it apart and reseated them. That fixed it and our heart rates returned to normal

[@EdwardInTX]

very cool!

[@reallaknight503]

I'm having the black screen issue as well but reseating the ribbon cable hasn't fixed it.

[@bgg]

​@@reallaknight503If the screen is black then it means that the signal isn't getting from the board to the screen. I'd double check the seating of the ribbon cable, I found it a little tricky to get it seated right. If that still doesn't work, check the other end of the cable and if that still doesn't work, check to see that there's power getting to the boards.

[@bonafidesa]

Thanks man! Great breakdown but mine had a lot more tape and what I assume was glue holding in brackets and nothing came apart as easy as you made it look 😂 I feel like I got catfished into saving a lot of money. Anyways, TV is working great now so thank you!

[@spanishchristian]

So I’m following your video up to the point where you have to remove the cover source PCB panel at 2:45 and there is no white hooks. What do I do? I’m using a NU7100 50inch

[@birthday_cakeman]

I am in the same boat and was reading the comments to try to figure this out

[@nawaf8258]

Just thank you man, ur a money saver

[@EdwardInTX]

you're welcome!

[@mrcreeperman13]

I just followed your video to successfully replace the backlights on my Samsung 55 inch tv. But half an hour after watching a bit of tv the newly replaced LED strip burnt out on the same side as it did with the old LED strip.. :( Any idea why?

[@EdwardInTX]

omg no! That was a bad LED strip. Request a replacement.

[@ginuwin2001]

Thanks great video having the same problem with the same model now I know what to get and how to fix

[@EdwardInTX]

awesome!

[@bridgetbosch5285]

Ok so first I want to say thank you. We now have our 55 inch Samsung waiting for a new backlight and everything went as you explained in the video. Only question is how do I know which backlight to get. Will it come with a different length seeing as we have a 55 inch and not a 65 or 43.

[@MI-iz7hw]

great video! but one question: whn you place the lcd panel on the sofa, isnt there any issues regarding dust and so on? which will be stuck no inside the TV?

[@EdwardInTX]

To my surprise nope!

[@tonyicaburi1622]

Is the tv afected if the plexi glas is broked in half

[@rgmotovlog674]

how many back light of samsung curve 55 inches... how many backlight will i buy????

[@yasserzahrani7322]

Thanks, it was very useful, guided me to replace mine, too.

[@snuggles3240]

is there any way i can get spare parts for those boards at 3:55 (i accidentilly fucked up 2 of those yellow ribbon cables.)

[@EdwardInTX]

Theyre called buffer boards, sometimes they appear on ebay but the connections are so small it can be difficult to reattach/solder

[@snuggles3240]

​@@EdwardInTX thank you. you absolute legend

[@sharolaid0190]

Do you have a video to repair the cracked screen

[@EdwardInTX]

Cracked screens cannot be repaired. You'd have to find a replacement panel.

[@Fredwithgame]

I repaired a same 55 Samsung tv like this but i has light bleeding like your tv, you said the problem is the position of tge first white paper.how should i do it on the first white paper to fix light bleeding in the bottom ?

[@EdwardInTX]

Actually I realized it's because of the transparent plexiglass. The best way is to dremel off the burned parts of it and put it back in the same way.

[@TheJONNYSHADOW]

I Would have liked a few shots of the whole back of the tv, can you confirm what boards are they, main board, power board etc?. Before I dismantle ours I am wondering if it is worth it cost wise. Ours went bang & I would like to replace all boards as I suspect the power board took them all out?.

[@EdwardInTX]

9:18 - 9:26 show the main board (green) and power board (brown). Those are the two main ones. If either of those don't fix it, there's a deeper problem in the panel that isn't worth fixing.

[@Aguadilla.]

This has how many leds? All together

[@caseydemars9350]

Awesome video! Worked for me

[@sivablore]

thanks for showing the led strip change. do you suggest to fix the vertical shadow on the screen by changing the led strip ? will it help? Also could you pls suggest the led strip for the curved samsung UN55KU7500 model.

[@EdwardInTX]

Yes, you'd need to change the LED strip to fix the vertical shadow. This is for the KU7500, but the led strip installation process will look different from the video as the LED are scattered across the screen. www.ebay.com/itm/154951141781?hash=item2413cec995%3Ag%3AeFcAAOSwLateeccK&amdata=enc%3AAQAHAAAAkMSl1Ks%2BPSe9V5Ol0qrJlK02c0N1Sxp5csU25%2BxOlb9DWYDGpJqQ9wH%2FylpV9uLs8T5yJCVE27ttIBryoHdMYyBFYscUxyHiyEetpCtle5YQ6X0ephVN92y84wjrQWArBvV6Xx%2B5MKh4FpNztva0GIMzJ%2Bhld8ana9B8Ko9bJAOQYel%2FuHkiMZCPfX2AExF4Ow%3D%3D&mkcid=1&mkrid=711-53200-19255-0&siteid=0&campid=5338782093&customid=&toolid=10001&mkevt=1

[@Crumperson]

Quick question, are the ribbon cables supposed to go on top or under the pins?

[@ChandlerC11]

The pins should be touching each other. There are two very little tabs on each side of the part the ribbon cable goes into. Slide it in so they are under those tiny tabs, and pins are facing down. If that doesn't answer your question, I don't quite understand what you are asking.

[@EdwardInTX]

Chandler is right. Under the pins.

[@Crumperson]

@@ChandlerC11 thanks for the reply. It turns out, that the ribbon cables had nothing to do with it, I just forgot to plug the remote sensor in, so I couldn't turn it on. The tv is good as new now!

[@gabrielcroitoru9502]

Very good video. Thanks for your help

[@TheAldoo1995]

Thanks man! It helped a lot, after I replaced the back light, the top looks darker than the bottom. Is there a reason why?

[@EdwardInTX]

The plastic diffuser panel distributes light to make it even. The best remedy is to saw off the burned parts at the true bottom and then reassemble it. Light will be even after that.

[@TheAldoo1995]

@@EdwardInTX I just change the position of the plastic, it looks way better. Thanks man!

[@EdwardInTX]

@@TheAldoo1995 Excellent!

[@4g63_Everything]

@@TheAldoo1995 what do u mean you change the position by mounting it upside down?

[@TheAldoo1995]

@@4g63_Everything I think I accidentally changed the plexiglass position. It didn't look as bright as it is supposed to do.

[@TheSalient0ne]

What is the correct position for the bottom sheet to prevent the backlight bleed?

[@EdwardInTX]

The same way it was taken out. Dremel or shave off any yellowing areas

[@codybotterill8268]

Do you have a link to buying new backlights?

[@EdwardInTX]

Yes, in the description ebay.us/scXAT3

[@Viatorejesse]

you needed only two led strips for lower edge ? no need for upper edge ? thank you advance.

[@EdwardInTX]

correct, due to how they made the plexiglass

[@frown]

How many strips does the device contain in total?

[@EdwardInTX]

2 light strips

[@D4nielF111]

my plexiglass is burned too much and i cut it off, now the light isn't dispersed as it should on the right part, where can i buy the plexiglass?

[@yeohkengmeng7181]

Hi Edward i changed the backlight and everything is ok except there is a bright spot in the middle bottom abit...what is the possible causes ya?

[@dellainspiron8929]

Hi now i have no image but both side led work and sound work help me please

[@Chromaticsketches]

Hey Edward! Thanks for this video, very informative. I'm wondering if these LED lights would work on my tv model; nu55tu8300? -Thanks!

[@EdwardInTX]

just looked -- yes they would

[@Chromaticsketches]

@@EdwardInTX Thank You Sir!

[@gwynforddafydd1397]

They also burn and damage the Diffusers .

[@AQAVAR]

Thanks. How to remove LED strips from base? Mine LED's are glued so hard screwdriver trick isn't for it. Any other tricks? Maybe some liquid tp desolve or heathing it up?

[@andrewbeckstrand4999]

So I accidentally got the ribbon to tear off of the board. Can I solder it back on?

[@EdwardInTX]

i'm not sure, never tried it. looks possible though but would be careful since the connector is plastic

[@ShotokanEditor]

plexiglass replacement?

[@danielbudzowski5774]

Did mine today, $32 for LEDs off EBay, made sure that part number matched up with samsung part. 2 hours to do complete disassembly, fix and reassemble.

[@EdwardInTX]

Very cool!

[@azzyaz3166]

Hey,do I need a glass lifter for the screen or do you think it’s safe to grab it by hands

[@EdwardInTX]

i grabbed it with my hands

[@azzyaz3166]

Oh ok thanks

[@Juliussilva17]

Great video! I can’t seem to find a strip for mine. It’s a un55ku7500f model. Are there any other LED strips compatible for my model?

[@mjreyes3550]

Try ebay,has stripes for all samsung models

[@LemonLoverCockatiel]

What about the 55" Samsung that has leds on the actual panel? What leds do I need to replace then?

[@EdwardInTX]

What is the model number of the TV?

[@VerStarr]

This is useful stuff. I always wondered how to fix screens like this

[@EdwardInTX]

Now YOU can do it!

[@sallymacalalad4166]

How much the cost of that backlight model

[@EdwardInTX]

@@sallymacalalad4166 backlight was $30

[@hectorcarrillo9814]

Amigo buen video nomas q el problema es q el difusor esta al reves por eso se ve asi y solo se puede poner de una pocicion si lo volteas la luz no sera pareja hay q cambiar difusor

[@SenseiDev47]

Hey I have a 65" with this problem but I went ahead and ordered the ones in your description ...did I just mess up????

[@EdwardInTX]

65 is longer. You'll need other LEDS based on your model.

[@dreknows]

Is Un55ku6500 similar I have image but I'm getting white spots why idea what that is?

[@LawrenceKamicha]

My curved samsung tv 32 inches was hit by my son and got broken. Any lead on where i can buy the screen part?

[@EdwardInTX]

panel isn't sold new, would just recommend buying a new tv unless you can find a similar tv with bad LEDs to swap the panel out

[@mugz1985]

Would this process be the same for all newer Samsung tvs? I have a UN58RU7100

[@EdwardInTX]

yes it works for that model

[@aizabenico-barra7605]

Hi..how many backlight i need to replace my samsung 55 inch tv?thanks

[@EdwardInTX]

2 bars if it's like mine

[@janbalga7702]

Great video. I just want to ask if the cracks on the plexiglass don't matter because there are quite a few of them.

[@EdwardInTX]

If there are brownish spots at the end, sand them off. The cracks will show a little brighter than the rest of the screen, but not really bothersome.

[@janbalga7702]

@@EdwardInTX OK. Thanks for the reply.

[@keithadkins3771]

Great job! Now I can tackle mine!

[@AlejandroMartinez-yl2br]

Very good video, but I have had a problem, trying to disassemble it the panel had cracked and I cannot find the replacement. any help to find it? Thank you!

[@Beast-mf7br]

500 minimum in Canada...prob around 400 if you're lucky in the states...better off buying a new TV...there's a profitable reason why these fuckwad manufacturers make the main screen so fragile!

[@larrychavez7381]

I have a cracked and burnt plexiglass just like in your video. Mine is a little worse, but do you know if you can get just the plexiglass? I am not having luck finding. Even Samsung does not have for resale to the end user and no techs within 200 miles

[@markgarrison9719]

Larry I feel you, man! I've fixed ten Samsung's with edge lighting all with the same problem. I've spent multiple hours looking for a way to purchase the plexiglass diffusor. Still can't find a place so I have to swap them with ones I find from broken screen TVs. Did you ever find a place?

[@amabeza]

Thank you. And, Subscribed 😊

[@KJCOD]

Are the leds just at the bottom or the top too?

[@EdwardInTX]

Bottom only in this model

[@KJCOD]

@@EdwardInTX do you know where they are for the UE55NU7100 ?

[@EdwardInTX]

@@KJCOD The ue55nu7100 is similar to the UN55NU7100-- it's two strips on the bottom

[@KJCOD]

@@EdwardInTX oh thanks

[@Scarfacegirl]

Near my entertainment center I have always kept a filtered 12x12 box fan , I've never had anything ever go out on me because of this . Started when I was young I got to have my box fan near me and as I learned heat was the main failure of electronics and noticable heat coming from tv, computer, Xbox and or surround sound.

[@muhammadsaufiyatim7207]

hi my tv is flickering...may i know what is the reason..want to try to fix by myself

[@EdwardInTX]

LEDs are dying. Replace.

[@erkpnc]

Hi i think i made a mistake the back light strip wont light up. What should be the problem.?

[@EdwardInTX]

the power strip that connects to the backlight goes into power board and the light, just check that connection

[@erkpnc]

@@EdwardInTX i disassembled my tv and wanted to test which ones the bad back light, when i plugged it in, no light and check the connection still no light

[@valorspeedqb4690]

Is there a tcon board

[@EdwardInTX]

Not in this one

[@erikhyler5714]

Does this process also work with the 65" ?

[@EdwardInTX]

If it's a similar model number, yes.

[@erikhyler5714]

@@EdwardInTX thank you

[@bradleydean8465]

Hi I have a issue and I really need help I replace backlight in a samsung UN65TU8000FXZA after installing the new light I test all with my backlight tester all work fine. After putting the tv back and plugging it in the backlight is not powering on.The powerboard is working because I'm getting power about 280v for the backlight. So my question is what could be the problem could it be the white connection between the powerboard and the lights. I forgot to mention I test the backlight using my backlight tester and the backlight work. I have some needle leads to my backlight tester so that's how I was able to test inside white connections.

[@pradhanmanu]

I could not find led strips for SAMSUNG ue65js9505 curve TV same as yours, 65" though. Any suggestion!!! By the way, great stuff that you put here, good job.

[@M.E63]

What country you in ?

[@pradhanmanu]

@@M.E63 Denmark

[@gpsingh08]

My Samsung LED TV has same backlight problem... would you repair it? If u then let me know how much it'll cost? I can't afford to pay more money

[@hlrspence31]

I have the same tv but the left side is good and the right side show but it's dark is this the same problem

[@EdwardInTX]

Yes

[@hlrspence31]

Again thank for the video, i was just wondering my tv is a UN55RU7300F and your TV is a UN55NU7300F will the same light fit

[@EdwardInTX]

@@hlrspence31 Yes. You're looking for part bn96-45913a

[@hlrspence31]

@@EdwardInTX thank you

[@mr.getitdone3490]

Video is First class. showing the reassembly makes it legendary thank you.!!🦾🦾🦾

[@CraigH316]

Same process for ue55ru7300?

[@EdwardInTX]

yes

[@samul6055]

Are the backlight LEDs for ue55nu7100k and ue55nu7100 the same?

[@dozadog]

Tried with LG TV and snapped a ribbon cable when trying to get the back off, so had to bin it.

[@teamcollom8027]

Could you send me the link for the led stips please

[@EdwardInTX]

ebay.us/KQqhgg LED Strips(2)for UE55NU6900 UN55NU6900 UE55NU7400 UN55NU7300 UE55NU7300 55NU7100

[@amareplaytimetv2380]

Same problem with my tv thank you for your video

[@EdwardInTX]

Good luck with the fix!

[@4g63_Everything]

Kinda helpful tutorial, coz my Samsung Curved TV (UA49KU6300G) has a vertical lines and some black spots on the screen. Im just assuming it has the same teardown process and im gonna try it now. Thankyou for uploading this.

[@SpecterNeverSpectator]

How it go

[@nsix9]

Hello 👋, I did this repair on my tv the only issues is the top of the tv is not bright enough , bottom lighting is perfect just top half what issue could I have ?

[@YureK___]

nice video, quick question tho, i have a samsung UE43NU7199 with the exact same problem but i can't find any backlights on ebay for that exact serial number, will any 43" samsung backlights work? or the ones from the NU7100 series maybe? please help

[@elflaco2039]

Please what steps should I follow to fix my 55 nu7300 it has a problem with backlight going very dark when I am watching any dark scenes

[@EdwardInTX]

same as i show in this video

[@shanewatkins5636]

Seems u might know the answer to my question. What's causing light bleed/4" bright flares on left and right on my 65" curved Samsung? Also a couple of dark spots a little larger than say a capsule💊??

[@EdwardInTX]

What model is it? Email me pics at my about link on my YT profile.

[@shanewatkins5636]

@@EdwardInTX un65js9000f. Sorry, not able to email. Couldn't find it under your about link. I'm guessing the flare's (very bright on one side, shadow on the other are internal cracks. I may dig into it tomorrow. Get a better idea on what's going on.

[@shanewatkins5636]

@@EdwardInTX @EdwardInTX so yeah.....it has all the same issues you had. Too bad the burnt cracked plexiglass can't be replaced. But thanks to your video, once I replace the LEDs, I'll have 25% improvement on light emitted and perhaps if I use windshield repair resin on the plexiglass it might help? Or super glue? I'm more hesitant on the super glue being that it's plastic.

[@kvothe4637]

​@@shanewatkins5636 did the repair resin work?

[@shanewatkins5636]

@@kvothe4637 it helped. Just wasn't worth the effort for as little improvement as it was.

[@CINCYB0Y]

Link for the leds please. Thanks

[@jamesheyworth1]

Randy, look up “tvchopshop” on eBay.

[@EdwardInTX]

www.ebay.com/itm/LED-Strips-for-AOT-55-NU7300-NU7100-BN96-45913A-15485A-UN55NU7300-UE55NU7105/224178438158?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

[@gxtscopedd]

what would it look like if you cracked only the black screen

[@EdwardInTX]

with it off, there will be an obvious lighter shade colored line through

[@gxtscopedd]

@@EdwardInTX what about with it on?

[@EdwardInTX]

@@gxtscopedd obvious crack on the picture and a black vertical bar spanning the width of the crack. It gets worse over time too

[@catalinnicolaevici2061]

I have a curved on different model it turns on go's to a blue screen then shuts off my electronic mentor says it's probably a resistor on the power supply. Dose that sound right? Mine is a Samsung UN65KU650DFXZA

[@NEKOSTEIGER]

how easily is to break the glass panel? I have to change the LEDs of mine but im scared ill break the glass. And sending it to repair its really expensive

[@EdwardInTX]

it's quite easy. You have to keep it as flat as you can as I show in this video