Great Video- No wasted time with fluff and annoying music. Very informative and quickly done - Thank You
@GarageKing9 ай бұрын
Thank you for the great comment
@andresrodriguez393 Жыл бұрын
I h I just followed your great video and replaced my water pump and thermostat. Took 3 hours with no surprises. Thanks. Saved a ton of money. 🙂
@GarageKing Жыл бұрын
Thank you for the great comment and glad I could help you out. Happy Saturday to you !
@docmopar426 Жыл бұрын
I plan on replacing my pump and t Stat. Your video is by far the best of all I watched. I do all my own repairs and this will make it so much easier😊
@GarageKing Жыл бұрын
Thanks so much and really appreciate the comment !!!
@paulalan3103 Жыл бұрын
For sure the most comprehensive.
@GarageKing Жыл бұрын
@@paulalan3103 Thanks for the great comment !!! Appreciate it !!
@jchadjezful7 ай бұрын
Never apologise for a long video - especially when it comes to this type of content. I am sure there are a lot of folks here that appreciate the level of detail you have provided.
@GarageKing7 ай бұрын
I appreciate that, and thank you. You would be amazed that some people would like a video like this to be 3min, and it's just not possible without skipping many important steps. Thank you again !!!
@Mr.Mitch1111 Жыл бұрын
Your video style is more friendly than most. You seem to take the time and effort to focus on the key spot to pay attention to, and you highlight some of the key difficulties you experience. I am now subscribed, so hope the rest of your vids are done in a similar style.
@GarageKing Жыл бұрын
Thanks for the comment and I appreciate that. My main mix of videos are the repair, then I do the Snap On monthly flyer, and some product reviews here and there. For the repair vids I do try to keep them technical with key spots and problems, I find that's much better than just talking :) I am a licensed mechanic so if you have any questions on the repair videos please let me know. Thanks !!
@scotthawkins5078 Жыл бұрын
Had a plastic thermostat. 2006. Had all kinds of trouble getting water pump to bleed system. Shot all electrical connections with contact cleaner and made sure all was tight. Runs like a champ now. Thank you for being so patient with your video. You are great to follow.
@GarageKing Жыл бұрын
Thanks so much for the comment, appreciate it !!
@scottishmarket Жыл бұрын
did you not replace the pump?
@GarageKing Жыл бұрын
@@scottishmarket Yes I sure did you can see where the old pump came out and the new one went it. I also put in a new thermostat.
@scotthawkins5078 Жыл бұрын
Yes. The pump was replaced when I realized nothing worked still. Once I did all of the cleaning underneath, it is working great. Thanks again
@GarageKing Жыл бұрын
@@scotthawkins5078 Anytime and glad you got it all working, it can be frustrating so when its fixed its a good feeling !!
@alfonsoramirez51903 ай бұрын
I like the way you go to the point and how you mention all the details and bumps of the job.
@GarageKing3 ай бұрын
Thank you good Sir !!
@matreyia Жыл бұрын
The proper method to reattach clip locked hoses is to first press the clips into the lock position, then attach the hose until you hear a click. This ensures the hose is absolutely locked. If you do it like you did in the video, there is a risk of the hose not being fully locked and it may pop off in the future.
@GarageKing Жыл бұрын
Very good call and thanks for the comment. I thought I did that in this vid, but I guess not. The biggest thing/tip to do is give them a wiggle and pull once they are on. This way if there is any doubt you know they are good. I actually push them forward and pull back so you can feel the hose start and stop, and you know its all good. Appreciate the comment :)
@stevesuy15517 ай бұрын
Being a new E90 Bimmer owner i often been overwhelmed or confused trying to find videos that were as infomative as this one. I hope theres more because as ive quickly discovered, being an E90 owner requires one to be more mechanically minded than for any other car. Luv ya work Mate
@GarageKing7 ай бұрын
Hello, yes there is more content coming !! I do a variety of videos, and the BMW ones take longer as they are more complex.
@caseycushing612412 күн бұрын
Do you have to replace the pump for a p0128 stuck open thermostat or can I just replace the thermostat?
@AnthonyRepetski9 күн бұрын
@@caseycushing6124you mine as wel replace the pump while your in there so your not doing this job twice. Unless of course the pump is relatively new. These things go like every 100k miles tops.
@Telstar_16 ай бұрын
Great detail in this video, thanks. I'm about to attempt water pump and thermostat change on my 2008 E90 318i with 2 litre N43 engine at 131k miles here in the UK. For info, a few days after the pump failed around town, it's now working again, but I decided to deal with it before it leaves me stranded somewhere. Due to long service life I got from the original parts, I've opted for like-for-like replacements - Pierburg pump online and a thermostat from BMW dealership, just need to grab the 3 bolts and some coolant after the weekend. Both my original and replacement thermostats are plastic and although the pump failed, I'm doing both parts at the same time. A little nervous about this as a novice DIYer, will be working on jack stands on my driveway. Thanks again for a very clear and helpful demonstration.
@GarageKing6 ай бұрын
Thank you for the great detailed comment, and good choice on the parts. Take your time, and you should be just fine. Be careful with the aluminum bolts for the pump, I can see them breaking very easily.
@JerryCori10 ай бұрын
That was the clearest explanation video I have ever seen. Great job man! 👍👍
@GarageKing10 ай бұрын
Thank you and glad I could help out !!
@yt_lota896 Жыл бұрын
Banger video. just picked up a 325i 2006 with under 120k on the dash. bought it for a steal only 800$!!! only issue was the water pump was bad. I believe I did the right diagnostic by holding the pedal for 10 seconds. I saw no fluid enter the revivor and that led me to the water pump. i a ordering the part this weekend and installing it here very soon after hope this fixes my issue as well as great video! you definitely earned my sub
@GarageKing Жыл бұрын
Thanks so much for the great reply, and I do appreciate it !!! Sorry for the delay, just got back from vacation :) Thanks :)
@angeloc1340 Жыл бұрын
I paid 4,200 for a 325i with 145k miles 😭 No issues so that is good though
@GarageKing Жыл бұрын
@@angeloc1340 well at least you have no issues !! Those can get expensive!!
@GarageKing Жыл бұрын
@@owen_636 Sounds like you did ok, plus in Cali there should be no rust, so the underside is most likely very clean.
@kimchiraptor580711 ай бұрын
thanks for this. I watched another video, and the guy tried the replacement without removing the radiator fan... he complained the whole way through. lol. and also decided to remove the thermostat first... squeezing it through the very tight spave between the fan, and the chasis... I asked if removing the waterpump first would be better because it would free up more space... no answer, but that is exactly what you did... thanks for that... I am pretty sure you've saved me 30 mins to an hours... thanks
@GarageKing11 ай бұрын
Thank you for the detailed comment, I appreciate that and I'm glad you were able to get something out of the video to help. Cheers
@alexwood99416 ай бұрын
The bolts the hold the sway bar have a circular bolt on top and are supposed to be welded to the rest of it, one of mine wasn’t. After hours of trying to grip the circle from the top, the nut stayed stuck on, I ended up drilling it out of there. It’s crazy how the parts of these videos that take you 1.5 seconds can take me 3 hours.
@GarageKing6 ай бұрын
Hey There, I didn't know about the factory welding. I guess I got lucky on this one as everything came apart alright. This only thing I actually fought with was the electrical clip for the waterpump, I struggled with that a bit. On my vids when I do struggle with bolts, most times I do put it in. I don't film the whole extra two hours or so, but I will put that in at like 50X speed or something like that to show the struggle is real. Glad you did get it all done and thanks for the comment.
@alexwood99416 ай бұрын
@@GarageKing I appreciate the video, no frustration directed at you, just the universe. Keep up the good work king
@GarageKing6 ай бұрын
@@alexwood9941 Thank you good Sir !!!
@kurtreinholtz202410 ай бұрын
Thanks so much for the great video. Saved me a ton of money versus having to take the car to the "stealership". My e90 is back on the road.
@GarageKing10 ай бұрын
Glad it helped! and very happy you were able to go it yourself (its a good feeling for sure). Keep that E90 on the road !!!
@docmopar426 Жыл бұрын
Finally got around to doing my water pump and everything went according to your video except my power steering bracket has a 10mm nut instead of a 8mm in your video. I keep referring to your instructions as I go. Again, great video and instructions
@GarageKing Жыл бұрын
Hey thanks for the comment and if the only difference is a nut I would say that's a win !!! Thank you
@ralphpena212610 ай бұрын
Good job ... Good video.... I got to do this today to my daughters whip
@GarageKing10 ай бұрын
Good luck with the job, and it helps if you have a magnetic bowl to hold all the bolts so they don't go rolling away !!
@AnthonyRepetski9 күн бұрын
@@GarageKingthere aluminum. There not sticking to no magnetic tray lol.
@GarageKing9 күн бұрын
@@AnthonyRepetski I know, but its possible for the impeller to spin on the shaft
@GarageKing9 күн бұрын
@@AnthonyRepetski I don't think its keyed
@karlinladeramusic2 жыл бұрын
Beamers are such smooth rides
@GarageKing2 жыл бұрын
Gotta love them, they are a "fun" car to drive !!!
@TheSeejay35 Жыл бұрын
Great car to drive but bloody expensive to repair
@skiesforhire Жыл бұрын
Until the check engine light comes on again
@AshtonLudlam Жыл бұрын
Not if you do the repairs yourself… unfortunately it’s 90% a pain in the ass lmao
@tusimp8860 Жыл бұрын
@@AshtonLudlamand they make em more difficult 😂😂 e46 u could just do shit but on e9x i have to KZbin everything
@sipwhitemocha5 ай бұрын
Thank you so much for your video especially including the portion where you took off the splash covers at the bottom...
@GarageKing5 ай бұрын
Glad you enjoyed the video and it helped you out. Appreciate the comment and thank you
@jeffscale1163 Жыл бұрын
You made that look so easy and pretty quick to
@GarageKing Жыл бұрын
Well I'm a pretty good editor haha !! I think with filming it actually took about 4 hours, If i didn't have to film then about 2hrs.
@jonathensulpizi4675 Жыл бұрын
Fun fact don’t put hoses on and then snap the ring down. Push the snap ring down and then push the hose on. When it clicks then you know it’s on all the way and the satisfaction factor as well with the audible click sound lol
@GarageKing Жыл бұрын
I like your fun fact, and never though of that. Thanks for the comment :)
@ryanhouston84656 ай бұрын
The 328i 07&08 I fixed used a plastic thermostat. Thanks for confirming my purging issue
@GarageKing6 ай бұрын
Thanks for the update and glad I could be of service good Sir !!!
@aimized1460 Жыл бұрын
Amazing video and such great details thank you a million
@GarageKing Жыл бұрын
Thank you for the great comment !!
@jakeyoung72425 ай бұрын
Wow thank you so much super informational ! I know this video is a year old and I don’t know if you’ll see this, but I’m looking to do the job myself as well. This is an absolute huge favor, but I’m kinda new into doing my own maintaice ( I just recently replaced my radiator and coolant system) I’m wondering if you could send a link to where I can find the right screw sizes for the pump and thermostat.
@GarageKing5 ай бұрын
I still check my comments on all my videos, I got a starter one in the works for this car. Anyway here is the link for the water pump bolts amzn.to/4c2SugC and I don't remember having to replace the thermostat ones.
@kurtreinholtz202410 ай бұрын
Thanks!
@GarageKing10 ай бұрын
Thank you so much for this !!!! I do my best so much appreciated !!!
@DanielGarcia-r5k5 ай бұрын
Thanks for taking the time to make this tutorial . It is very helpful.
@GarageKing5 ай бұрын
Glad it was helpful, and thank you for the comment, I'm working on one for the starter now :)
@rghant Жыл бұрын
Man thank you for this video! You will save me tons of money!!!
@GarageKing Жыл бұрын
Then I did my job haha, so glad it will help you out, and with the rates shops charge these days you will save a bundle !!
@kccraven1340 Жыл бұрын
Your the man ! Nice work , keep it up and thank you for sharing. May you have great health wealth and abundance.
@GarageKing Жыл бұрын
Thank you for the great comment, much appreciated !!!
@joseg3691 Жыл бұрын
The best video on this topic. Thank you sir.
@GarageKing Жыл бұрын
Thank you for the great comment !!
@jantewhite66436 ай бұрын
I'm a woman and my water pump, thermostat, needs to be replaced. I will try my best to replace, w/my friend. The bmw dealer wants a 💰to fix!. My previous mechanic, i had to fire his ass!😂 I appreciate your video!. you're awesome!... and you're gonna save me a ton!. Thanks a lot!. ❤
@GarageKing6 ай бұрын
Thank you for the great comment, I really appreciate that. Take your time and go slow, take your laptop under the car, just don't spill anything on it :) If you have any questions along the way just let me know, and good for you for tackling the job, it will be a great feeling when you are done :)
@TheGreatGastronaut Жыл бұрын
Great video - gets right to the point without fluff. I just finished the same operation on my 2013 E92 SULEV and based upon the guidance provided, it was largely uneventful (!). I did have a couple of observations to pass along to help others. * There is an electrical connector on the passenger side of the fan shroud that goes to what looks like a radiator surface temp sensor on the backside of the radiator inside the shroud. Associated with it is a pass-through bushing that loosely fits in the side of the shroud, a connector and two cable mounts. One cable mount is part of the connector body. Both mounts must be removed and the cable disconnected. The connector body mount releases from the shroud with a quarter turn. The other is a snap-in and is pried out. * When reinstalling the fan assembly, the aforementioned bushing must be aligned in a groove in the side of the fan shroud. It’s held in place by the shroud and the radiator. If it’s not correctly aligned, the shroud won’t fit up right. * The fan assembly has three pins that align it and hold it tight against the radiator at the bottom. It also has a slide in slot on left and right side midway up. The slot has a retention tab that must be released to slide the assembly up. All of these retention and alignment features must be correctly engaged for the assembly to fit up correctly when reassembling. *The fan assembly has a hook feature the also retains and aligns with the chassis crossbrace along the top. If everything mentioned is properly aligned, the fan assembly drops onto the hook and the single locking T25 screw lines up. If anything isn’t just right, no dice on the screw lining up.
@GarageKing Жыл бұрын
Thank you for sharing, and thank you for taking the time to write this!! I can tell it took you a while to write so I really appreciate it, and thanks for the positive comment on the video. Happy Sunday to you my friend !!
@TheGreatGastronaut Жыл бұрын
@@GarageKing It’s a community of interested people and I’ve been both a pro and shadetree mechanic over the past 50 years. We all learn from each other. You took the considerable effort to post a great how-to for DIYers that saves probably $1200 in stealership labor charges (the local San Diego dealers base labor charge is $260/hr) for what becomes a very routine repair if you have the guidance. My respect and appreciation for your effort was to add tips on what I found to be the more difficult elements so others will be even more empowered. Kudos and I look forward to viewing your other postings!
@GarageKing Жыл бұрын
@@TheGreatGastronaut Thanks very much for the feedback, you obviously have a lot of experience so I'm glad you are sharing. That knowledge is valuable and deserves to be shared !!
@karlinladeramusic2 жыл бұрын
Cmon 8k! Man you are growing so fast!
@GarageKing2 жыл бұрын
I know, so close, getting there. My view count has dropped a bit. Still doing well, but in the summer my air conditioning vids were going crazy !!!
@mlnags2829 Жыл бұрын
Am 77 old gram with first older BMW. This is very interesting. Replaced cracked water overflow and never bled so getting a low fluid light 1x each time (5) I’ve driven then disappears. Will bleed and check for for water flow. If light disappears 👍🏻- if not will check with Motörhead son then may or may not need pump replacement. Thnx for explaining.
@GarageKing Жыл бұрын
Thank you for the comment and congrats on getting your first older BMW, they are fun cars to drive around !! They handle great for older cars and even outperform many new ones.
@ignaciocruz75225 ай бұрын
Just did all the hoses plus thermostat and water pump, my thermostat was plastic original and plastic new one oem, it’s a 2011, will say since I was doing all the hoses it was easier to remove the fan and just bang the job out the way, good shit tho it’s hard to make a good video working on cars I know I couldn’t
@GarageKing5 ай бұрын
Hey thank you for the comment, and thank you for realizing its really not easy to make these videos !! Many times I run into rusty bolts, super tight spots, and I have to get that camera in while I work. Thank you !!
@bennyhutchings95589 ай бұрын
Thank you for a very informative and to the point video. ❤
@GarageKing9 ай бұрын
Thank you and glad it was helpful
@peacefulmomentstoreflectvl9022 жыл бұрын
Easy way to replace BMW water pump.. so helpful.
@GarageKing2 жыл бұрын
Thanks so much, this was a bigger job !!!
@nhanthanhhuynh Жыл бұрын
You are the BEST!
@GarageKing Жыл бұрын
Thank you good Sir !!
@jabberwockytdi8901 Жыл бұрын
2011 E82 N52 plastic impeller housing, metal pump body plastic thermostat housing from the works, now nearly 70k miles just about to replace pump with Pierburg all metal and Mahle ( OE as far as I know ) Thermostat housing. Metal Thermostats dont's seem to be available at all so plastic ones are prob not an issue?
@GarageKing Жыл бұрын
Yep,. I put a plastic one in, you can see in the video, and its still going strong. I was not able to get a metal thermostat either. I think the plastic ones must be fine.
@jamalnasir28462 ай бұрын
Great video very clear and easy and commentary is great and easy explanation very nice each small thing is covered very helpful great thanks so much.
@GarageKing2 ай бұрын
Glad it was helpful and thank you !!
@earlfrancis76 Жыл бұрын
The aluminum thermostat housing is better than the plastic type , plastic type tends to have premature leakage
@GarageKing Жыл бұрын
You are right for sure, problem is BMW does not make the aluminum housing anymore. If you order a replacement you get a plastic one :(
@ponche1217 Жыл бұрын
Hello is awesome video thank you ,one question how is the water pump working is a good item for your bmw ?
@GarageKing Жыл бұрын
Hey There, and thanks for the comment :) a good working water pump is necessary for the BMW as it cools the engine. If it's not working the engine will overheat and that can cause a lot of problems.
@danielcleveland11944 ай бұрын
sub'd and rep'd thank you for this, I'm inheriting a 2010 328I with 93k on the clock and you made it look easy good sir. I also will keep the as long as it works don't replace it as I'm going through and proactively replacing things, spark plugs, coils ect just to make sure no issues. Also appericate the coolant information as I've got a tacoma and cx-30 and they us the premix stuff which is far easier. Again thank you so much for the information.
@GarageKing4 ай бұрын
Glad I could be of help, Just FYI - I just did a no start check and starter replacement for your car, that was last week. I alternate content between vehicle repairs and the Snap On tool deals. Feel free to reach out anytime !!
@LilacGlo2 жыл бұрын
Hey GK! Here catching up! Another superb video! Super informative! Learnt a great deal from it. Thanks for sharing 👍🏽💯❤️
@GarageKing2 жыл бұрын
Thank you !!!!
@jacobadams81132 жыл бұрын
Thank you for this! Doing this Friday. How many hoses do you need to disconnect from the water pump? Just 2?
@GarageKing2 жыл бұрын
Hey there, I think there is 3 in total, there is the one at the front of the pump, then there is the thermostat group, and then the one for the housing right above the balancer if I remember correctly. I show them pretty clearly in the vid. Believe it or not the footage was over 3hrs for this job and I compressed it down to 17min !! That was the shortest I felt I could do it without skipping steps.
@jacobadams81132 жыл бұрын
@@GarageKing thanks again! This helps a lot! Truly appreciate you making this tutorial
@GarageKing2 жыл бұрын
@@jacobadams8113 Thanks brother !!
@jacobadams81132 жыл бұрын
@@GarageKing are the bolts for the water pump and thermostat E10 & 10mm?
@GarageKing2 жыл бұрын
@@jacobadams8113 Hey There, they are E10. Having a regular 10mm around is always good no matter what the job !!!
@crazyolazy73934 ай бұрын
I just replaced thermostat and didn’t fix my problem water pump next. Thanks for the video I sub and I have a 2006 and it was a plastic thermostat
@GarageKing4 ай бұрын
Thank you for the comment, mine is a 2006 with a plastic thermostat as well. Hope you have a great weekend, and at least you know the water pump is doable now.
@94tontonche5 ай бұрын
Hello, great video, how many miles will it be necessary to change it, I have 110,000 miles 325i 06/2010, BMW tells me that if it works well I don't need to change anything, I'm going to do 1000 MILES and I don't have want to have problems.Thank you.
@GarageKing5 ай бұрын
Hey There, I think they are giving you good advice. This is one of those things where if it aint broke, don't fix it. You never know when its going to fail, so its best to wait until it does.
@94tontonche5 ай бұрын
@@GarageKing Merci..
@GarageKing5 ай бұрын
@@94tontonche pas de problème, heureux de vous aider !! No problem, glad to help :)
@ShakotanRon Жыл бұрын
Great video. Is that a failed all metal pump? I assume it was motor failure, not pump failure? Metal thermostat housing, that's so much better
@GarageKing Жыл бұрын
Hey There, the factory pump failed and the car overheated. I wasn't sure if the thermostat was damaged so I replaced it with a new one from BMW. Interesting the new thermostat right from BMW is plastic so I could not get a metal replacement. I wonder if the new cars are all plastic? This vehicle was a 2008 I think. I agree with you the metal housing is much much better !!
@luasremoto Жыл бұрын
Thanks brother I appreciate your help my bmw 128i is running perfect now 👍🏽👍🏽👍🏽
@GarageKing Жыл бұрын
Thats awesome and glad I could help you out !!!
@caseycushing612412 күн бұрын
Do you have to replace the pump for a stuck open thermostat or can you just replace the thermostat? I’m on a tight budget
@GarageKing12 күн бұрын
You can just do the thermostat
@roastedhd285219 күн бұрын
So what caused it to not spray during the bleeding procedure, did the blades fail or it just fails electronically inside the pump?
@GarageKing19 күн бұрын
The pump fails, when it gets weak the pump is going and then eventually nothing
@javi_335i Жыл бұрын
Im about to do this tomorrow. Thanks for the video👍🏽
@GarageKing Жыл бұрын
Thank you for the great comment, take your time and also its good to get the car up as high as you can as it makes it much easier !! Happy Sunday to you :)
@javi_335i Жыл бұрын
@@GarageKing I was able to install the pump and thermostat today exactly like you did in the video. Just need to pick up a new upper radiator hose tomorrow morning and bleed the system. 👍🏽👍🏽
@GarageKing Жыл бұрын
@@javi_335i That is awesome !!!! Glad you got it all done :)
@ivanreyes8182 Жыл бұрын
I have 2 328is and both had the metal ones both replacement came in plastic as well.
@GarageKing Жыл бұрын
Thanks for the comment, and I think that's what BMW is doing now. My replacement was plastic, I think they all are. Thanks again
@gerritgordon69093 ай бұрын
Awesome thank you for skipping the boring parts. LOL SHOT DUDE THUMBS UP
@GarageKing3 ай бұрын
Thank you good Sir !!!
@losidude114 ай бұрын
My 06 had a steel thermostat. It still worked perfectly at 180k when i replaced it along w the waterpump. The OEM plastic Wahler pump barely lasted 40k until i started getting thermostat codes :/
@GarageKing4 ай бұрын
Good to know, I did save my steel thermostat (no codes yet) but if I ever get a thermostat code I think I'm going to put my steel one back in.
@jacobthompson80787 ай бұрын
Do you have to drop subframe to do it on a 2006 330xi?
@GarageKing7 ай бұрын
I think you can still get it out, but its tight. I believe one of my other viewers was able to do it, but had a few choice words afterward :)
@caatodin74668 ай бұрын
Ive been trying to find something for the 07 x5 3.0si. Though some differences seem evident some seem simliar. Am i right??
@GarageKing8 ай бұрын
I believe you have the N52 engine so it should be pretty much the same.
@rebound23456789 Жыл бұрын
I have a question, im owning a e90 320i n46 from 2005. Is the waterpump there not electric yet ? I tried the steps to turn it on while the engine is off but it didnt work. When its on i see its working.. Thanks for the video
@GarageKing Жыл бұрын
Hey Thanks for the question. I believe you do have an electric waterpump as your e90 is a 5th generation but maybe the 320i doesn't? You could always call the dealer parts department and ask. They would tell you right away if its electrical. If its electric then perhaps the steps are off a bit (like time between fob activation and pressing the gas pedal)
@jbopiddy21694 ай бұрын
Great video
@GarageKing4 ай бұрын
Thank You !!
@mariad750 Жыл бұрын
I heard you can get to the WP from the wheel well, is this an option?
@GarageKing Жыл бұрын
I highly doubt it, I just don't think you could do that. If you somehow can, please let me know as I would like to know !!!!
@koran136 Жыл бұрын
So my coolant does pump like how yours does at the start of the video. I'm still having overheating issues, when I scan for codes I get 2E84(missing pump)? Any thoughts? I've replaced the thermostat(just throwing money didn't have a code for that) & did plenty of bleeding
@koran136 Жыл бұрын
How long should the bleeding take? I've read the instructions and it says about 12-15min, when I've done it it kept going over 20min?
@GarageKing Жыл бұрын
That is really weird, your computer thinks the pump is missing, but its running....... I would check that ground connection near the pump, and give the pump connector a wiggle.
@GarageKing Жыл бұрын
Normally bleeding should not take more than about 10min. There is a vent on the top of the reservoir on some vehicles that you can open when filling. The big thing is to look for a solid stream of fluid when the pump activates.
@linovaladas2553 Жыл бұрын
Great video! Thanks.
@GarageKing Жыл бұрын
Thank you good Sir !!!!
@rodneyfuller6034 Жыл бұрын
I have a 2011 E93 convertible and found there is additional frame reinforcement under the engine which prevents the front sway bar from dropping as you showed. Any guidance on the best path forward there?
@GarageKing Жыл бұрын
Hummm thats a good one, you know I have never done one on a convertible, but I have worked on other convertibles (not BMW) and when I have worked on the underside the bracing was always a bolt on, bolt off, never welded. The only thing is if you remove the bracing (if its bolted on) you have to make sure the car is jacked up squarely. I use a quick jack so there are 4 lifting points and the car is not twisted like if you jack on one side. You could try to get around the sway bar, but I'm not sure if its possible. I always lower it.
@samgod2 ай бұрын
The water pump in my '06 330i was changed in 2016, radiator in 2020, expansion tank & cap in December 2023, thermostat this January (2024), and the corroded plastic valve connecting the coolant tube to the head gasket was replaced with an aluminum one in July. Thee's a small leak in my radiator and my water pump drains the battery (8 amp drain) when the engine's off. Removing fuse 54 when parked stops the pump and preserves the battery. While I obviously need to replace the radiator yet again, why's the water pump running-- beyond the 12 min bleed-- when the engine's off?
@GarageKing2 ай бұрын
That is a bit of a puzzle. It should turn off. If you know anyone who has a bi-directional scanner they can turn the pump on and off with the scanner, and see if it responds properly.
@McDzy10 ай бұрын
Would this work for a 2007 bmw 328i? Also how do we know if the water pump/thermostat are failing?
@GarageKing10 ай бұрын
Yes it should, procedure is the same. Very hard to tell if thermostat is failing as this type of thermostat is enclosed so its almost impossible to check. I suppose if you were creative you could submerge it in boiling water and then try to see through the housing if it opens.
@McDzy10 ай бұрын
@@GarageKing gotcha! i was just asking because im planning on getting an 07 bmw 328i and not sure if these have been replace yet or not.. its an auto with 85k, how reliable are these 328i cars?
@GarageKing10 ай бұрын
@@McDzy They are actually pretty reliable, reading your earlier comment I can address the pump. To check the pump operation you can use a scanner, or the car can do a self test. See this vid I dd on the self test, not sure if I put it in this vid. kzbin.info/www/bejne/aHumg4V4itGLadU Overall the 328i is a nice car and 85K for mileage is not too bad.
@McDzy10 ай бұрын
@@GarageKing appreciate it! yes, ill be looking at an 07 328i tomorrow with 85k miles, who has 2 previous owners, and seems to be on top of maintenance, im just curious whether or not its reliable, since ill be trying to do the maintenance and simple repairs by myself... whats the common tick sound issues that others are mentioning in regards to the generations around this time?
@GarageKing10 ай бұрын
@@McDzy The common tick issue is lifter noise. These vehicles also have noises from the front of the engine sometimes which can be traced back to the belt or tensioner, those are ones that I would not worry about at all. Make sure the oil is full, and you can do a check (there is not dipstick) so you use the turn signal and go through a menu. These engines get noisy with low oil. Lifter tick is usually a very light ticking that goes away and then can come back at times, and normally is not serious. If you want to make sure that it is lifter tick and not something more involved then I advise to take it to a mechanic. Hope this helps
@binaozdemir71857 ай бұрын
Insane video
@GarageKing7 ай бұрын
Thank you for the comment
@paulalan3103 Жыл бұрын
I have a code to replace the thermostat on my 2006 325i. Should I replace the water pump while I am down there? The car has 121,000 miles and there seems to be a leak somewhere on the bottom. I have the covers off and car in the air and I can't see where it's coming from.
@GarageKing Жыл бұрын
Good question and I would consider doing so. They are both coming out so inspect that pump very closely, if there is any signs of a leak (even 1%) I would do it as you are in there anyway and its a pretty big job. You might see some staining and thats a give away. Also your car being a 2006 with 121,000 miles, if its on the factory pump, well its probably getting near the end of its life anyway. For the leak make sure you check along the bottom of the radiator, sometimes they leak at the crimped portion (where the aluminum meets the plastic) and the coolant runs down. You could always give it a cold pressure test. Pump it up, and then come back in a few hours, pressure testers are pretty cheap amzn.to/3ZgLjMa
@paulalan3103 Жыл бұрын
After watching your video the second time, I went ahead and bought the pump too. Yes, I too figured it was a going. That being said, I already replaced the radiator earlier this summer and I hope I don't have to replace it already. @@GarageKing
@GarageKing Жыл бұрын
Good call on replacing the pump, I would have done it as well. Fingers crossed for you that once you do the job your coolant leak will be no more !! @@paulalan3103
@paulalan3103 Жыл бұрын
@@GarageKing I found the leak. The top of thermostat to cylinderhead coolant hose was leaking from underneath. I was unable to see it looking down on the motor so I crawled under while the car was running.
@GarageKing Жыл бұрын
@@paulalan3103 Well that's a win and sounds like it was a hard leak to find, those ones are tricky and glad you found it, as that is not an easy hose to get to !!
@RoadHeros610 Жыл бұрын
Freaking awesome video
@GarageKing Жыл бұрын
Thank you good Sir !!!!
@laonongvnvlog95982 жыл бұрын
have a nice beginning of the week 15 lik.e
@GarageKing2 жыл бұрын
Thank you !!!!
@johnbori6869 Жыл бұрын
Thank you !!!
@GarageKing Жыл бұрын
Thank you for the great reply !!
@tayoni80011 ай бұрын
Does driving with insufficient coolant increase the chance of water pump failure?
@GarageKing11 ай бұрын
Yes
@ericasperheim1540 Жыл бұрын
What do you call the tool used to undo the steel hose clips?
@ericasperheim1540 Жыл бұрын
Best I found was radiator hose pick
@GarageKing Жыл бұрын
Yup it was a large Snap On radiator hose pick
@GarageKing Жыл бұрын
You guessed right !!
@nostalgicdivine3675 Жыл бұрын
One of my bolts for the water pump was not tightened down all the way. What will that affect ?
@GarageKing Жыл бұрын
Yikes, yup it could. It could let the pump vibrate (its on rubber mounts) and while I don't know what would happen, there is the possibility that it could rub something loose or create a wiring problem (loose or broken wire) I would fix it if you can.
@AnthonyHernandez-ms5ym Жыл бұрын
My 335i 2008 started leaking coolant, I was told it was the electric water pump. Does that cause a coolant leak ?
@GarageKing Жыл бұрын
Hey There, it can leak coolant so it a possibility for sure.
@mikemata623 Жыл бұрын
Check your radiator as well, I have seen leaking radiators splash coolant onto the pump making it look like it's leaking.
@GarageKing Жыл бұрын
@@mikemata623 Good call
@hahnachavez1338 Жыл бұрын
Hi, sorry, stupid question….but is the water pump the same for a 2008 & 2006 325i?
@GarageKing Жыл бұрын
Hey There and no stupid question here !!! To be honest I'm really not sure. I think they are. Best thing to do would be to click the link and then enter your car information and see if its compatible. I would like to say its the same, but I can't confirm.
@terryzak17429 ай бұрын
The upper water pump fastener is difficult to see on the E60/N52, and if you're not careful enough, you can wind up removing the adjacent AC compressor bolt. Don't ask me how I know...
@GarageKing9 ай бұрын
I won't ask you how you know LOL, but I will thank you for sharing :)
@BrotherRobb Жыл бұрын
How is the MOSTPLUS waterpump and thermostat going?
@GarageKing Жыл бұрын
Hey there, I think I used a Doorman as that was available at the time, they dropped it from Amazon and BMW wanted too much for a pump. I researched and the MOSTPLUS had a lot of sales and positive reviews. You can get the Doorman on the Canadian Amazon, but they raised the price to like 800, not worth it at all. The Doorman pump is still running great.
@miraciamiracia800710 ай бұрын
What was the symptoms of the one you replaced? Was it able to bleed or not?
@GarageKing10 ай бұрын
It did bleed, but it was very weak, I can't remember if I showed the before and after, that may have been at the end of the video. If I remember correctly I filmed what the pump did before, and after. I may have put it right at the front, or right near the end.
@miraciamiracia800710 ай бұрын
@@GarageKing It is at the end, I see it. So it wasn't overheating. I'm asking because mine doesn't bleed at all and overheating.
@GarageKing10 ай бұрын
@@miraciamiracia8007 Mine was overheating, even with the pump being weak, it was still overheating.
@miraciamiracia800710 ай бұрын
@@GarageKing Got it, thanks for taking the time to answer
@GarageKing10 ай бұрын
@@miraciamiracia8007 Anytime
@karlinladeramusic2 жыл бұрын
Great vid!
@GarageKing2 жыл бұрын
Thank you !!!
@Rasinzz7 ай бұрын
did you have to drop the subframe?
@GarageKing7 ай бұрын
No
@Rasinzz7 ай бұрын
@@GarageKing ok thanks!
@GarageKing7 ай бұрын
@@Rasinzz Anytime :)
@rrudyhamilton Жыл бұрын
did you lower the rackpinion looks like the video was skipped information left out
@GarageKing Жыл бұрын
Hey there. Nothing was left out. I did not lower the rack. This is a 2wd
@rrudyhamilton Жыл бұрын
ok okay my mistake@@GarageKing
@GarageKing Жыл бұрын
All good brother !! @@rrudyhamilton
@viacheslavkurbatov1753 Жыл бұрын
Best job))
@GarageKing Жыл бұрын
Thank you good Sir !!!!
@viacheslavkurbatov1753 Жыл бұрын
@@GarageKing buddy, she just got lit up and the check came out, ordered a pump with a thermostat, you have the clearest video for understanding, I think during the installation process I will watch 5 more times
@GarageKing Жыл бұрын
@@viacheslavkurbatov1753 I appreciate that !!! Believe me it took many hours to film and edit so hearing your comment for me is job well done. Thank you :)
@Olga-oq2nzАй бұрын
How long time does it take?
@GarageKingАй бұрын
Depends if you are filming it LOL, If you are taking your time, maybe 4-5 hours, once you do one, then the next one will be 1/2 the time.
@jameslyons9457 Жыл бұрын
Can I ask what you use for jack stands or do you have a life? Excellent video BTW. Edit: Quick Jack! I found it on one of your other videos. Will be shopping for a set now.
@GarageKing Жыл бұрын
Hey There thanks for the comment, and you can ask me anything !!! You found the video kzbin.info/www/bejne/ZnvWhqKNZ8aLhaM I love this quick jack thing. I use to use jacks with jack stands, but it takes forever to jack up a vehicle where you can get all 4 wheels off the ground with the vehicle remaining level. Plus if you are close to a wall jacks are a pain. I have had the quick jack for over 2 years now and I love it. You saw in the video it pretty much lifts everything !!! Thanks for the reach out :)
@omairjafri10842 жыл бұрын
great video, curious how long did it take you overall
@GarageKing2 жыл бұрын
haha, well well, if you count filming then most of the day as I had to ensure I had the camera positioned to get the shots, the editing took a few hours as well. But if I didn't have to film it, then I would say 2-3 hours at a nice pace (not beating yourself up)
@whitbyretreat145 Жыл бұрын
Great video! How much on an average this job would cost including the pump?
@GarageKing Жыл бұрын
Hey there, you can get the pump and thermostat kit on Amazon for about 170. amzn.to/3eKtG4n Then I would buy a jug of antifreeze and maybe 3hrs labour? So maybe 200 for parts and whatever 3hrs would cost at a shop where you live.
@cuocsongthonque90292 жыл бұрын
amazing video 14 lik.e
@GarageKing2 жыл бұрын
Thank you !!!!
@sonnyjamescrocketts4822 Жыл бұрын
My pump just gone today, its at garage so just seeing what's involved.
@GarageKing Жыл бұрын
Hey Thanks for the comment, as you can see there is a little bit to do !!!
@miguelelelelel7 ай бұрын
did it, thanks!!!!
@GarageKing7 ай бұрын
Awesome and give yourself a pat on the back, this is not a small job !!!! Plus you saved some good $$$ :)
@AnManHydro Жыл бұрын
Broke some clips still not able to get the top bolt on the pump out super tight in there 😂super mad 😂
@GarageKing Жыл бұрын
Take a break if you have to, I know sometimes its best to just leave it for a few hours and come back so you don't get frustrated. Believe me I know !!!!
@e46gunna99 Жыл бұрын
Hey was wondering if the water pump held up good being that’s it’s from Amazon ?
@GarageKing Жыл бұрын
Its still working, I remember checking the price of the factory one and it was like buying another car LOL. I decided to try aftermarket and it worked out for me. Happy Sunday to you !
@Johnwick08190 Жыл бұрын
if I’m getting code 2e83 does that mean my pump is going out ?
@GarageKing Жыл бұрын
It could, but it could also mean the system is dry (has air in it) if its not properly bled.
@0546amandakim16 ай бұрын
I have a 2009 BMW 328 I and the thermostat housing is plastic also
@GarageKing6 ай бұрын
Thank you for the comment. I guess the plastic must be ok or they would not make them. The one good thing is they don't corrode so that's good.
@0546amandakim16 ай бұрын
Thank you for the detailed, instructional video. Any chance your from Fl.?
@GarageKing6 ай бұрын
@@0546amandakim1 I wish !! I'm actually from Canada, hello from the great white north !!
@RoadHeros610 Жыл бұрын
OMG is that how I actually bleed the cooling system that will also check if the water pump is working correct
@GarageKing Жыл бұрын
Yup you bet, no special tools needed. A scanner can activate the pump, but you can do it this way :)
@karlinladeramusic2 жыл бұрын
Electrical clip! It's the lil things
@GarageKing2 жыл бұрын
Ya you bet, can you imagine forgetting that. This was a good vid to do. Took a while to edit, but glad I pushed this one out :)
@droppadoose Жыл бұрын
if you go under there and your pwr sterring lines are that rusty I would DEFINITELY sand them and paint them before they get worse
@GarageKing Жыл бұрын
Hey good comment and that would definitely make them last longer for sure. Never thought about doing that, thanks !!
@MakaveliThaDonKilluminati4 ай бұрын
Just installed a brand new water pump after my last one failed Absolutely fine for 5 months then BOOM brand new water pump failed now i gotta DO IT ALL OVER AGAIN
@GarageKing4 ай бұрын
Well, you are going to get faster and faster at it. If you have a friend with a BMW, you can lend your services. Sucks you have to do it again, but at least you know what you are getting into.
@MakaveliThaDonKilluminati4 ай бұрын
@GarageKing haha i didnt do it paid 1800 for a shop to do it
@GarageKing4 ай бұрын
@@MakaveliThaDonKilluminati OMG !!
@MakaveliThaDonKilluminati4 ай бұрын
@GarageKing i know right but that includes the thermostat too. I should of done it my self but i truly got no time working 55 hours a week
@GarageKing4 ай бұрын
@@MakaveliThaDonKilluminati I hear ya, 55hrs is touch man, that's a lot of hours
@willlong42586 ай бұрын
So it's not a hard job necessarily, just a bit of a tight fit removing the pump and thermo. Tempting me to get an E90 330i 🤔🤔
@GarageKing6 ай бұрын
The E90 is a fun car :)
@BvhugfFgigigАй бұрын
So if I go to bleed my coolant right now ? And if it’s not pressurized I know something’s up ? Do I need to drain and refill in order to get that bleed ?
@GarageKingАй бұрын
No, when you car is cold there is no pressure, so you bleed it with the radiator cap off (no pressure) and when the car is cold. You wait for a steady stream of fluid. Not sure if I put it in this video, here is the bleeding video. kzbin.info/www/bejne/aHumg4V4itGLadU
@nenuko039 ай бұрын
my thermostat exploded 2 times because plastic! but thanks for the video..
@GarageKing9 ай бұрын
Sorry to hear that, and it sucks they changed from aluminum to plastic, its obviously cost, but did they really save that much......
@nenuko039 ай бұрын
@@GarageKing "" brands business """ but others brand doesn't mean its cheap. ecs tunning sell aluminum parts. like radiators etc. people thinks original its quality.
@GarageKing9 ай бұрын
@@nenuko03 Oh I see, I didn't understand at first what you were saying, thanks for the clarity.
@aVOID9 Жыл бұрын
The plastic is terrible I have a 335i and replacing the plastic parts cause it’s not reliable for the performance I’m seeking eventually in the future
@GarageKing Жыл бұрын
I hear you, but the problem is everyone is making the thermostat out of plastic as its cheaper and no one wants to pay the extra for the all aluminum parts.