Replacing Coffee Dispensing tube - Saeco Odea Giro

Hi Everyone,
This is useful video which shows how to replace your old broken coffee dispensing tube with new one.

[@donnettethayer4956]

I cannot believe that, with the help of this excellent video, my beloved Saeco Odea Giro LIVES AGAIN! I was terrified the whole time, but we fixed it! I grovel at the feet of the Saeco master.

[@rsander2000]

I had a problem with a fast blinking red light on my saeco odea. When the red light flashes fast it indicates a problem with the flowmeter. Thanks to your videos I was able to open my machine and locate my flow meter and take it apart. I cleaned out all the tubes opened the lid of the flowmeter and cleaned that out too. There was no obvious obstruction anywhere but after assembling my beloved saeco again it works like a charm. Your video is essential to have because it shows very well how to open lids and what screws need to be taken out and it makes it easy to put everything back properly. I am very grateful for all this information and it was more than helpful. Great job. Great contribution. Thanks for sharing your knowledge.

[@hminiarj]

I repaired a free machine using this guide. You, sir, are a caffiene angel. Thank you!

[@lumpyfarts]

Thank you so much for sharing your knowledge. It would have been impossible to open the machine without it. I got our Odea apart, replaced the O rings in the steam valve, put it all back together AND IT WORKS :)

[@gilbertosonda6952]

You have just saved me. I couldnt find any manual showing how to open the machine and although i didnt need to replace the dispensing tube the video was a life saver just by showing the first steps to remove the covers. Thank you very much

[@vincentflorish9448]

Thank you for uploading, broke that part last week and thought that was it for the machine. But after finding your clip I ordered part online and following your details I am delighted to say back up and running again. Thanks, easily saved me €100 even if I could have found someone to fix it for me.

[@danielaschlichter3682]

Thank you very much, I never repaired a coffee machine but your video was excellent and it helped me. I was told the machine couldn't be repaired and I only paid about 13 Euros by replacing one little peace and the help of your video. Thank you a lot!

[@patrickdriscoll9962]

Miroslav your Saeco videos are SO WELL DONE. Thank You. You are a supurb instructor!

[@glengiovannetti7598]

Miroslav - thank you very much for this video. Your video helped us diagnose the problem. After spending a few dollars for a replacement part on Amazon your step by step instructions and tips made this very easy to do even for a novice.

[@2011LittleWing]

Thanks a lot! Dankeschön! Muchas gracias! This video is so good. My tube has been broken I didn`t know how to do it. But you are my man! And for all the not knowing coffee afficionados all over the world.

[@JackAstor365]

extremely nice demo on how to proceed disassembly!!! 5 stars👍👍👍👍👍

[@billmaciejewski9764]

Fantastic! I have a Go, but the steps were almost exactly the same. You have saved me quite a lot of money, instead of sending my machine off. Thanks!

[@christianbini9030]

Hi Miroslav, A thousand thanks for this video!!!....your explanations are very clear, step by step, and my coffee machine is now repaired thanks to you. Without your uploading, I would certainly have changed it for a new one.....and for more than 400€! Best regards!

[@bradscott9049]

Can you advise on where to purchase this part?

[@christianbini9030]

@@bradscott9049 You can purchase this part here : www.fiyo.fr/saeco-ecoulement-soupape-valve-d-ecoulement-de-cafe-complete-pour-cafetiere-11010544?device_brand=769 Best regards

[@yvesderyckel4500]

Your videos are quite perfect. It's so easy to follow your instructions to disassemble and reassemble the machine. Thanks also for the spare parts. My machine is now ready for the next Expresso. Yves

[@a2studioca]

Hi Miroslav, you are gem!!! Thank you so much for your helpful video. I fixed my machine and without your video i would never do it. Big Big Thanks!!!!

[@MauPasq1]

Thanks Miroslav! I could repair my car seeing this video! Really it has done very well! Thanks again!

[@alvarofernandez5217]

Many thanks for your video!!! I have repaired my machine by your video! 👏👏

[@meeshuisman4342]

Thanks for this video. You saved my marriage. My wife was very happy including myself. You did a grat job with this video.

[@theKXSB]

thank you so much for you brilliant video, I would never have been able to without your help. Thank you

[@fraren5014]

merci beaucoup, c'est la seconde fois que vous sauvez ma machine à café !

[@powerbower69]

Thank you for the good work Miroslav. I have a Saeco Giro plus and your technical instructions and advise help me a lot. Even when you are showing it from a slightly different model it helps me a lot. Thanks!

[@OpaFritze46]

A very good mechanik. This Clip was very usefull for me . So I could help my daughter to get a reasonable repai, by doing it myself. Dankeschön, der Clip war wirklich hilfreich.Thank you very much Miroslav!!

[@dawnoftheunleashed2927]

Thx for the very helpful video. I thought it would be much easier to fix but with your description it was no problem.

[@karinm3004]

Thanks for this very helpful video!! now we can enjoy our coffee again. :)

[@elsberndvoice]

Thank you, Miroslav! I fixed my Saeco with your help!

[@maximebouchard545]

Very helpful, thanks a lot! I was able to open my machine and, along with your other video, fix the grinder that was stuck!

[@jorgeheribertocifuentes8259]

Excellent video; I could repair my machine thanks to these complete instructions.

[@ArielZibziner]

Cheers Miroslav, this was very helpful, I bought the part and replaced it myself. excellent guide and tips!

[@michalismeramveliotakis9225]

Thanks Miroslav. That was really helpful. I managed to fix my machine. Keep the good job up!!!!

[@miroslavstoicev8821]

+Michalis Meramveliotakis Thank you! :)

[@michalismeramveliotakis9225]

+Miroslav Stoicev I will be ordering some other parts soon to fully service my machine. Do you have any clue how i can adjust the quantity of the coffee that the machine grinds to make one coffee? Is there such an option?

[@a2studioca]

Miroslav, you are phenomenal. I own this unit for 8 years now and only because of your unbelievable videos I was able to fox already 3 major problems. Thank you again!!!

[@davehane8313]

Thanks, Miroslav. Well done video. Hardest part was getting the silver curved front and top cover to click back in place. But freshly brewed coffee is flowing once again.

[@bradscott9049]

Where can this part be purchased?

[@Djschale79]

Thank you for your support, now my machine is working :)))

[@zowie8888able]

Thanks for this video. I saved a lot of time not having to work out how to open it

[@marcoeliasschoeling7226]

Very nice instruction! Many thanks!!! Helped me exact for that problem!

[@kamilaswelt]

Hallöchen und vielen lieben Dank für das Video:) ich habe meine Saeco talea Giro plus repariert. Der einzige Unterschied ist das oben keine Feder und keine Kugel drin war. Thausend Dank für das Video. LG Kamila

[@tambor25]

Thank you very much, good explained!! You are a teacher

[@David2222]

Thank you Thank you Thank you. Fabulous resource.

[@rosangelaeichler8296]

Thank you! It's was really really helpful!!!!!

[@dinodg7625]

Thanks very good video so I got the job done no problem

[@mannyfix2811]

Thank you for this job.

[@flame04ful]

Thank you so much!You helped for me lot of.👌✋👍 :) Happy new year!

[@64CEZZAR]

Congratulations on Stoicev video, very well explained, helped me a lot, my máquina entered ant and your video saved me!! Sucessos!

[@khussalpradhan5626]

64CEZZAR ."mfodeanmeoeodeanmws

[@HudnilsonFaria-nu7sq]

Muito obrigado pelo demostrativo de como abrir a Ode go e profissionalismo

[@romaincortes5263]

Merci pour votre video qui m'a été très utile pour réparer ma machine !

[@lampcleat]

This is good for taking it apart & putting back together!

[@gchavarria31]

You rock! I have espresso again thanks to you 😁

[@domenicoventriglia2388]

Hello Miroslav amazing video 's it helps me a lot , i have some problems with my talea ring plus , everything is working but when i select coffee there is no coffee coming out , instead the water is coming out where the brewer is , Can you advise

[@janburgel8277]

Thank you for these very useful and clear instructions. Can I ask you a question? One of my two Saeco Odea machines makes a load noise and the whole machine vibrates when brewing the coffee (not when grinding the beans). Brewing time is about 45 seconds for a tall coffee. Could the pump be causing the noise? The other machine refuses to brew a complete coffee. It only produces a few drops, the brew unit seems to struggle and then drops the coffee in the container while releasing steam and hot water. I would very much appreciate your help!

[@johng1077]

Thanks for the videos would this procedure be close to replacing the flow meter valve i have a fast blinking exclamation mark which was followed from the frothing tube dripping? Thanks for any help John

[@Seychelllian]

Thanks for this! It is very very helpful.

[@anstegan]

Miroslav, thanks for video! :)

[@asimbilloo9746]

awesome video thanks so much! but my issue is water leaking from brew group. i bought a new brew group and still leaking. A LOT! so now im thinking it might be a water tube etc. any tips sir?

[@Nick-jw5ok]

Thank you🎉!

[@balabasl]

Thank you!

[@toto2110]

Hi Thanks for great videos, need your help to determine a problem, my machine makes a very loud noise while pouring the coffee, can you tell me if its the water pump or else. also i will need to buy the parts to replace

[@Treshonorable]

Great video -Thanks a lot this really helped.

[@scotusforis_72]

Hello Miroslav! Thank you for making this video. It helped me change the dispensing tube. It worked for a few cups of coffee and now when I switch the machine on, it starts to heat up and all the red lights stay on and flash continuously. Do you have any ideas? I simply changed out the tube, nothing else. Thank you.

[@bojankovacevic6900]

Thanks, i've made my machine work again! :-)

[@quinschoonewelle7617]

Thnx for the response :-) I will take a look at this!

[@djandymarc]

Hi Miroslav, Thanks for the video. Just one question. My Displensing tube isnt broken but seemed like it was restriced, so i took apart the tube by removing the 2 screws in the elbow of the tube. Inside that chamber there is a spring with what looks like a stopper. Which way does the spring go? Does the stopper side belong on the brew unit side or the front tube side? The reason why i did open it up is because i cant get the brew cycle to prime. The steam wand works fine and the brew group itself is fine (i have tested in another machine)

[@ЮлианХрисчев]

Благодаря , току що оправих една одеа гоу със същия проблем иначе я бях засилил за кофата спести ни едни 600-700лв за нова машина.

[@MrBetrunk56]

thank you 4 the videos

[@momanskiakabiffbuz6004]

At first I want to thank you for this helpful video. But now I have problems readjusting the knob, where you change the grinding level. How do I know at what degree I have to put the little knob into its place?

[@lumpyfarts]

Hi Miro. Please could you help with some info on how to dismantle the Talea Giro Plus. The control knobs and dispenser are different to the Odea and I do not want to pull too hard and risk breaking parts. Thanks again for your videos.

[@pjmesquitar]

hello. your videos are great. a have an odea is great to, but when i press to take a coffee the machine dispense very press in the first water dripping, sometimes must go take off the shirt because she take dirt with coffee, can you help with the cause please?

[@johng1077]

Not sure my question posted before if it did i apologize it isn’t showing for me. My question is this procedure in this video close to what you would want to follow for flow valve replacement, i am taking a guess since my frothing tube was dripping for a while. i got the o-ring set and a flow meter.

[@okizvecan7930]

Thank you I find this video usefull OKI

[@philippecarvalho1265]

Merci !!!!

[@robertdaradics9998]

Thank You for your video!! I would need your skilled help! Ihave a Saeco Talea Ring Plus , was ok until now, but from some time, when I turn it on ,after trying to rins (mine is set to rinsing first) is says: Rinsing failed and it enters in Priming Water Circuit -function and goes on like that even for one hour ! sometimes. -but miraculously it comes back to be ok.-the next day same thing :( checked the water flow meter-is ok, water pump-ok(disassembled it)brew group-clean ,ok not leaking. Could it be the distribution valve??? . or did I miss something? Please help me!!!!!!

[@zee76039]

Miroslav, I have Saeco xsmall coffee machine. When I try to brew coffee with it something kicks the brewing unit out about 2 mm and the red alarm light starts blinking slowly. What can be the problem? Can you help me please? I even tried the test mode. Everything is ok, but in 0 level of test mode when you first turn it on, the right green light is off. At that level both green lights should be on. What does it mean?

[@evggan2685]

Thanks bro

[@walidmahmud2026]

Can you please show how the Thermoblock cam be calcified? I opended the same machine, but can't calcified. Thanks for help ! Good video

[@jorgeromero-mo3rt]

Here can I buy the plastic or silicon tube to replace in my coffee maker

[@ejet9900]

Hi i have saeco ring plus everything work but there’s no water coming when you make a coffee. Could you tell me what is the problem? Thanks

[@emilsondeoliveira4358]

Muito obrigado... Perfect

[@dorosmichael2370]

Hi Miroslav, I have a Saeco Odea go, when i switch the machine one the red light comes on and it does not go away so that the machine can work, do you know what the fault might be? The only problem the machine had was with the water, it did not stop or recognise when the tank was empty Can i please have your advice Thanks

[@samyouanes467]

thank's a lot

[@jeffearl5753]

My machine leaks clear hot water on the left side when brewing or after brewing. It (mostly) ends up dripping right above the water reservoir onto the lid or through to the bottom of the machine and onto the counter. I have not opened up the machine yet, but what is likely the culprit?

[@ciarankelly5459]

Hi, great video thanks. My Odea Go has stopped working. It starts the grind okay, but I can hear the grinder motor under pressure and the grinding stops before the water pump starts. At this point the red exclamation light comes on. I have tried descaling, but that has not solved the problem. Is there some possibility that the grinder motor becomes clogged? Thanks

[@miroslavstoicev8821]

Ciaran Kelly Hi Ciaran Kelly! :) Probably the grinder motor is damaged. You need to disassemble the grinder motor and to check all elements from the part. Please, check for damages over the GROUND COFFEE OUTLET CONVEYOR ASSY, usually when this part is damaged it has many grinded coffee around the grinder motor which damage it. I'm considering to make a special video for grinder motor. You can follow me and when the video is made you will know. :) Best Regards, Miroslav Stoicev

[@ciarankelly5459]

Hi Miroslav, I followed your video for dis assembly and unscrewed fixing screws on the lid of the ground coffee conveyor assay, so that I could prize it open. It was blocked full of ground coffee as you suggested. I used a vacuum cleaner to remove the debris, and re assembled. The machine now works again. The machine is 6 years old and in daily use, so the assembly is quite worn and ground coffee leaks from the assembly into the motor housing. I reckon this will happen again over time, but at least I know now how to fix. Thanks again :)

[@miroslavstoicev8821]

Ciaran Kelly kzbin.info/www/bejne/o4TQhnRrZ72BZrM

[@rumenvelkovski3942]

Здравейте г-н Стоицев ! Благодарение на Вашия клип през последните три години два пъти сменям диспенсера. Изключително съм доволен от тази кафе машина и не искам да се разделям с нея. Сега имам друг проблем - кафето изтича много бавно и на капки и част от водата изтича в легенчето за обработеното кафе . Може ли да ми помогнете със съвет ?

[@stahlw]

Hi. Thanks for the great video. Do you know how I can fix this problem on my Saeco Odea Go: When brewing coffie the water leaks out of the steamer "wand" (the one that makes steam for heating milk). It leaks quite a lot. Is it a seal in the steaming/heating part of the machine that needs to be changed, and du you sell parts for that? I would very much like to buy a spare part for that. Thanks. Ps, I have tried to descale the machine with cirtic acid, and it didn't seem to help. Actually it made it a bit worse.

[@miroslavstoicev8821]

Greetings, stahlw! Thank you for writting me! :) Happy New Year! :) You can find repair kit for Odea in my eBay store like follow this link: www.ebay.com/itm/Saeco-parts-Repair-Kit-for-Odea-Talea-Gaggia-Platinum-/400830581903?ssPageName=STRK:MESE:IT The descaling cycle will not help, probably the gaskets are damaged. If you have any other questions I'm available for help and answers. Sincerely Yours, Miroslav Stoicev

[@stahlw]

Miroslav Stoicev Thanks for the reply. I would like to buy the repair set from you. I am in the process off disasembeling the machine now. Is it possible, that you can show me/ tell me where to replace the old/damagede seals /gaskets from the steamer?

[@stahlw]

Miroslav Stoicev I think it is the vaulve to the steamer wand that is broken. The one you turn in order to get steam out of the wand. Do you sell new ones of these?

[@miroslavstoicev8821]

stahlw Hi again stahlw, You can find this steam valve in my eBay store like follow this link: www.ebay.com/itm/Saeco-parts-Steam-Valve-Kit-for-Odea-Talea-and-Gaggia-Platinum-Models-/400830584893?ssPageName=STRK:MESE:IT Kind Regards, Miro

[@joachimbeckmann8770]

Hello, unfortunately I do not speak English and am using the Google Translator. Do you have a video in which the removal of the pump at the Odea Go is shown? Would be great and Thanks in advance. With kind regards Joachim Beckmann

[@yunusaustralian]

Hi guys i have same machine and have a problem with the steam nob wont working. Same time was working at the moment stop. How to fiz it what is the problem coming from any idea?

[@clauspeterlitz7965]

Hi, good job, I will have to try to do this. Could you tell me what the Part Number is for that Part(Coffee Dispensing Tube) Thank You

[@miroslavstoicev8821]

+Clauspeter Litz Here you can find manufacturer number of this part: www.ebay.com/itm/SAECO-PARTS-COFFEE-DISPENSING-TUBE-FOR-ODEA-MODELS-/111831363633?ssPageName=STRK:MESE:IT

[@Zeeg1957]

Do you have a video that explains why water comes out of my water wand when i make a coffee and how to fix this. Is there a wahser or seal that needs to be replaced. Thank you.

[@miroslavstoicev8821]

Hello Joseph Quercia, Thank you for contact with me! :) If your coffee machine is Saeco Talea or Odea probably the seals are damaged. Here is the repair kit you may need to fix it: www.ebay.com/itm/Saeco-parts-Repair-Kit-for-Odea-Talea-Gaggia-Platinum-/400830581903?ssPageName=STRK:MESE:IT Sincerely Yours, Mirsolav Stoicev

[@Zeeg1957]

Thank you very much for responding and I have learned so much from you.

[@guissoumaissam9286]

Hello, Thanks for this video. My machine grinds beans but no coffee is dispensed. Do you know how I can fix this problem on my Saeco Odea Go?

[@miroslavstoicev8821]

Hello, Thank you for contact with me! :) Can you please describe more exactly the problem you have? Is there some water flow from the dispenser or not? Kind Regards, Miroslav Stoicev

[@guissoumaissam9286]

Miroslav Stoicev Thank you for your quick reply. All the lights indicator are green, and the machine is ready to make coffee. I press the coffee button, the machine grinds beans, but no coffee or water flow from the dispense. When the machine has finished, I have the grinded beans on Dregdrawer not wet and some water slip under the machine. The hot steam works fine.

[@carolecole238]

@@miroslavstoicev8821 Do you know why? I also don't have water coming out but it does grind beans

[@quinschoonewelle7617]

Hello Miroslav, I replaced the tube but when i want to make coffee it leaks water at the brewunit side. Do you know how to fix this?

[@miroslavstoicev8821]

Hello Quin Schoonewelle, Thank you contact with me! :) Happy New Year! :) Can you please take a look closer the brew unit (brew group) for gaskets damages and also on the boiler valve? I will awaiting your reply to help you. Sincerely Yours, Miroslav Stoicev

[@mrjavierberraquero]

Hi .. I have a Saeco Odea Giro. Coffee does not come out , it makes the cycle but nothing comes out . The circuit runs out of water . You could help me find the fault . Thank you

[@karaokelatviesuvalodaagrai1872]

Thanks. Miroslav. Budu po russki, dumaju chto ponimaesh. U menja kofe stalo kakim to ne krepkim, ranshe bylo ochenj chernoe i krepkoe. kak dumaesh v chom problema.

[@baysezgin]

Thank you for your support Miroslav *****************

[@staicu_dragos]

saeco talea priming water continous in to the drip tray , there is a way to check , solutions?

[@albertmerizian3965]

Hallo, I have a problems with Saeco Xsmal , too much water in the collecting container, thanks

[@katharinemarsden3276]

thanks. good job. but you didn't put the silver screw back. No problem. I did it for you.

[@miroslavstoicev8821]

Here is the video which explains the problems coming from coffee grinder: kzbin.info/www/bejne/o4TQhnRrZ72BZrM

[@the.kristian.experience4689]

моля направи видео на български знам че си българин!

[@stxt6199]

Русский видно же

[@brunobertuola9125]

non spiega in italiano

[@zygmuntgorszczynski2819]

Thank you!