Does the aligning of timing needed for 240sx ka24e?
@SuperchargedPathfinder3 ай бұрын
Same engine.
@bomd765 жыл бұрын
Do u have to remove the cam sprocket? Or just loosen ? Have to do this ? Thanks for the video 👍
@SuperchargedPathfinder5 жыл бұрын
You have to remove it. This requires zip tie'ng it to the chain so you don't lose the correct tooth. You also need to wedge the timing guide so the chain doesn't slack inside the timing cover.
@streetclasscc51893 жыл бұрын
When to the wrecking yard to pick up some rocker arms how to i know if their bad? Or good?? Found a set that had no play on them when installed but when i took them off the head the little plunger on the rocker are very stiff. Is that normal?
@SuperchargedPathfinder3 жыл бұрын
That is normal once they are bled.
@sipmeister3611 Жыл бұрын
i just did my chain and im hearing the rocker arms or bad valves not to sure but im about ready to rool the damn thing down a hill. gets no power and sputters with the rocker ticking of course.
@SuperchargedPathfinder Жыл бұрын
Check that the distributor is on the right tooth.
@jackcarrigg3 жыл бұрын
Do you think 🤔 if I took off the valve cover an squrted some penitent on the rocker I might loosen one lifter?
@SuperchargedPathfinder3 жыл бұрын
Maybe but I doubt it.
@franciscozamudio68585 жыл бұрын
What can be wrong if the bolts from the shafts doesnt wanna tight anymore
@SuperchargedPathfinder5 жыл бұрын
Not good. Sounds like they stripped out.
@GOBEARS19855 жыл бұрын
Can you replace just the bad rocker arms? Individually?
@SuperchargedPathfinder5 жыл бұрын
Yes you can. You will still need to remove the rails.
@GOBEARS19855 жыл бұрын
What brand rockers do you recommend? I normally use oriellys.
@GOBEARS19855 жыл бұрын
Is it possible to install the wrong rocker or will only the correct one fit?
@mr.channel64674 жыл бұрын
Does this thing have the same engine as the 1995 Nissan hard body?
@SuperchargedPathfinder4 жыл бұрын
That is a 1995.
@jclagriculturalconsultatio34933 жыл бұрын
Good night, could please send me the website so i can download the service manual
@SuperchargedPathfinder3 жыл бұрын
Www.nissanservicemanual.com
@JustinTwilley5 жыл бұрын
Hi if im only removing one rocker arm shaft would i loosen 1,3,5,7,9? Or would I have to remove both? Also Im replacing the back two on the right side if your facing the truck, I hope I ordered the right ones..one ex and one intake? crap now im nervous lol.
@SuperchargedPathfinder5 жыл бұрын
If the rocker is on the same side as the exhaust manifold it is an exhaust rocker. So if you are looking at the motor from the front and the rocker is on your right side it is an exhaust rocker. Now there are front and rear exhaust rockers too so be aware of that too. You can remove one rail but i would loosen both up in order so not to tweak the head.
@JustinTwilley5 жыл бұрын
@@SuperchargedPathfinder thanks
@3RAN7ON6 жыл бұрын
1:02 I thought that the ka24e engines have two exhaust valves and one intake per cylinder. So why does the intake side have more rocker arms? Wouldn't that be the other way around?
@SuperchargedPathfinder6 жыл бұрын
KA24e has 2 intake valves and one exhaust valve.
@3RAN7ON6 жыл бұрын
Nismo D21 oh. Thanks for the reply. I guess the guy who sold me that exhaust header lied to me LOL
@SuperchargedPathfinder6 жыл бұрын
Lied, or might have been thinking of the twin cam KA24DE engine.
@kevinc90065 жыл бұрын
Your back asswards
@sandwich.5207 жыл бұрын
what manual were you using hayes manual?
@SuperchargedPathfinder7 жыл бұрын
I was using a Nissan factory service manual. The plans for the chain wedge came from a Chilton manual.