Replacing starter on 2007 Toyota Tundra

[@johngalvan2263]

I literally just changed my boss starter thanks to your video he thought I had to take off alot of stuff thankyou

[@javip2672]

damn it's about time someone shows how to get to it the right way. under the car not under the hood. easiest way to replace...

[@555mainesmonsters]

Well, I’m about to start this job right now so wish me luck it’s 5:30 PM to see if I can get it done in two hours

[@Carguy-fn5nf]

Update?

[@mattsivert2594]

Damn that thing is clean

[@isaiah-lava5.086]

Just did this whole job in less than 2 hours 🤑🤑

[@loens90]

I just tried on my lx570 2009 and i had to take off the selenoid to fit in there and moving up the oil line for the tranny that pass by the oil pan i think the tundra and sequoia have a lil bit more room but at least you helped me still thanks?

[@karljohnson2864]

Does this truck have a lift or anything that would change the geometry between the A-arms and the CV axle¿

[@79ramirez79]

Stock

[@bean-matic9322]

on a 2014 tundra is it the same space in that spot bc i did everything you did up until that point bc it wouldn’t fit through, maybe i didn’t try long enough but i ended up loosening up the exhaust

[@donaldgeter7657]

Damn did you have your axle replaced before?

[@bluefallon6374]

Well I didn’t see you take it out !

[@Mrdubomb]

How did you get the starter heat shield out and back in without destroying it?

[@79ramirez79]

@Mrdubomb it was tite but a little finesse so it could be reused

[@ricqik]

My starter didn't fit this way either. Maybe it's different starters.

[@cutlerscrew6]

Same. My starter from the dealership will not fit like this. But geez I wish it did !

[@skunkape1824]

Mines a 5.7 ask my buddy u have to take cat out i got out finally thanks for you vid

[@mrcoasttime21]

YOUR AWESOME!!!

[@mikewest712]

this was not an oem starter. if you do this job, remove the engine mount and jack it up an inch.

[@79ramirez79]

Yes it was an oem new starter better design and pricey

[@skunkape1824]

My 08 tundra doesnt have enough room

[@79ramirez79]

Bryant Poe 🤔hmmmm maybe 08 is different ... the old starter was tight getting out the new replacement from dealer is wayyy smaller to make job easier but cost about 350 for it

[@gringrinny9012]

79ramirez79 no go on a 2010, 4x4... no where near to be able to remove through the a arm like in this video... tomorrow i'll pull out part of muffler, exhaust manifold will stay intact...

[@xlilnetx]

It’s because he has a simple 2wd, everyone else he’s talking about has a 4x4 lol

[@luckyrover5454]

I’m four afternoons in. Still can’t get passed the transmission lines. Coolant lines are off still no go.

[@79ramirez79]

Xlilnetx video shows the front cv axle which would make it a 4x4

[@salvadorcuevas7998]

I do my just today thayou

[@martymartinez8793]

Lol you didn’t have the solenoid attached to the starter

[@79ramirez79]

Starter solenoid is attached watch video closely

[@oldschool6268]

Thanks bro !

[@79ramirez79]

Old school no problem i hope it helped

[@Whyus793]

How old is this video? That truck looks new for a 07' my 07' looks like hell underneath. My starter is still original.

[@theopentoybox6084]

I have a lift and it worked this way…. I believe it only works this way if you have a lift.