Audi A4 B7 | Bi-Xenon HID DIY Headlight Upgrade installation

The Audi A4 B7 is a very classic car with a luxurious appearance. Your car didn't come out of the Audi factory with OEM xenon headlights? No need to worry. With our Bi-xenon mini H1 twin kit it's now possible to transform your headlights to true Bi-xenon projectors! Check out our full instruction video on how to retrofit your headlight with these awesome projectors and compete with OEM setups for a fraction of their cost!
𝗬𝗼𝘂 𝗰𝗮𝗻 𝗯𝘂𝘆 𝘁𝗵𝗶𝘀 𝗴𝗿𝗲𝗮𝘁 𝘂𝗽𝗴𝗿𝗮𝗱𝗲 𝗸𝗶𝘁 𝗵𝗲𝗿𝗲:
retrofitlab.com/products/audi...
𝗜𝗻𝘀𝘁𝗿𝘂𝗰𝘁𝗶𝗼𝗻𝘀:
0:01 Remove the caps from the rear
0:05 Heat the headlight to soften the sealing
0:11 We put the headlight in a carton box and heat it
0:15 1600 Watt heatgun for 16 minutes
0:23 Remove the lens clips and rubber
0:44 Seperate the lens from the housing using a flat screw driver
1:14 Remove the H7 halogen bulb cap
1:20 break off the cap channel with a plier
1:28 Place the small rubber washer over the projector shaft
1:33 Insert the Bi-xenon solenoid wires through the cap shaft and insert the projector through the fitting
1:43 Place the H7 adapter ring and secure the projector nut
1:59 Don't tighten it fully yet, you might want to do some final rotational adjustment when the headlights are mounted on the car
2:04 Mount the bulb holder
2:20 Click the shroud centric ring inside the shroud (this shroud has been modified for fitment)
2:23 Apply a few drops of glue to be sure the shroud will stay on
2:50 Remove all finger prints using a fine cloth
3:00 If you want, apply some butyl to make sure the headlight will be free of moisture
3:20 Press the lens on the housing and bake it again
3:48 Now that the sealant is soft, press the lens on the housing using pliers and secure the lens by placing the metal clips
4:17 Place the solenoid plug back on the wires
4:25 Connect the H7 high beam splitter for the solenoid to function together with the H7 halogen high beam
4:49 Drill a 20-22mm hole in the bulb cap to guide the wires through
5:16 The wires will be connected to the ballast and H7 low beam plug. Because the Audi A4 B7 has Canbus, this is the only wiring setup that can be used
5:22 Insert the bulb in the projector and secure it with the clip
5:48 Connect the 12V ballast wires correctly, red to the yellow cable (+ positive) and black to brown (- negative)
6:07 Click the cap back on, you are ready to mount the headlight to the car and enjoy a luxurious Bi-xenon projector headlight! :-)
𝗔𝗱𝘃𝗮𝗻𝘁𝗮𝗴𝗲𝘀 𝗼𝗳 𝗮 𝗕𝗶-𝘅𝗲𝗻𝗼𝗻 𝗽𝗿𝗼𝗷𝗲𝗰𝘁𝗼𝗿 𝗿𝗲𝘁𝗿𝗼𝗳𝗶𝘁 𝗸𝗶𝘁:
• Much better light output
• Double high beam (xenon + halogen)
• No glare
• Lower energy consumption (35 watt instead of 55 watt)
• Luxury OEM look
𝗖𝗵𝗲𝗰𝗸 𝗼𝘂𝘁 𝗼𝘂𝗿 𝗻𝗲𝘄 𝗙𝗮𝗰𝗲𝗯𝗼𝗼𝗸 𝗴𝗿𝗼𝘂𝗽:
/ europeanheadlightcommu...
𝗙𝗶𝗻𝗱 𝘂𝘀 𝗼𝗻:
Facebook: / retrofitlab
Messenger: www.m.me/Retrofitlab/
Instagram: / retrofitlab.com_official
Our website: www.retrofitlab.com/
#Audi #AudiA4B7 #A4B7 #Aharon #Retrofit #DIY #Upgrade #Headlight #lighting #HID
#Retrofit #LED #custom #improvement
𝗢𝘂𝗿 𝗦𝘁𝗼𝗿𝘆:
Retrofitting refers to the addition of new technology or features to older systems. These days there are a lot of people who put a simple plug & play xenon kit in their halogen headlight housing in an attempt to improve night vision and looks of their vehicle. In fact they don’t realize that their headlight beams are often worse than before. Night vision achieves relatively little improvement on night vision because of a poor beam pattern, which increases the blinding of other road users. This is because their headlight housings are designed for halogen and not xenon.
A true Bi-Xenon projector update is now possible for your car. Such an upgrade will significantly improve your light output from 700-2100 lumens to 2800 and 3500 lumens, without blinding other traffic with glare from your headlight. Upgrade your headlight OEM style!
The latest high power Led bulbs will upgrade both the exterior and interior lighting system of your car. Led lighting is becoming more and more popular in the automotive market for obvious reasons. They have longer lifetime, use less energy and improve safety with their fast response time.
Do you have any questions? Do not hesitate to contact us, we are happy to help you out!
Good luck with your retrofit!
These products are not ECE-approved and must not be used on public roads in any exterior application. Use on public roads will invalidate both the operating license and insurance coverage.

[@picollokano]

Thank you ! :) Have a wonderful day !

[@travisricephotograph]

Love the heat gun box hack.

[@eagleeyes170]

this is very satisfying to watch

[@Retrofitlab]

Thanks :)

[@kulyro]

one of the most perfect videos i've seen.thank you!!!!

[@aahmed2016]

Thanks a million on this video. Great, straight to the point, and no extra bs.

[@MuhsinunChowdhury]

meow.

[@killevil4581]

Thank you for making this video because I just saw what I need to do to my new projector lamps. The left one is not rotated level with the right one so I need to take the bulb out and look inside to see how off it is. Going crazy try to found out how I can do it.

[@devengutierrez8758]

Wow you make it look really simple. .looks SICK

[@R5GTT]

Amazing idea and may have to try this with my golf gti mk5 lights. Well done retrofit you sure know your stuff 👍

[@ocingur]

Great job! Congratulations.

[@Utubeash7]

Nice and clean retrofit. Those shrouds look so OEM

[@sking379]

By the way excellent work, you make it look easy!!!

[@1PITIFULDUDE]

Nice job! Looks OEM with the shroud you chose.

[@erwin411]

you make this look easy... i try on my car.. thanks for the video

[@BigbrookLORDOFTHE7SEAS]

Excellent work trully impressed!

[@devengutierrez8758]

No problem man...keep up the great work.

[@blowrus]

Шикарно! 🍓

[@fa2919]

Hmm will try that next..thanks alot :)

[@johnhere1426]

Thanks for answering me Retrofitlab So up till now i understood that the solenoid or the black and red wires are responsible for making the light switch from low to high beam mode. So it means that when I will have these lenses installed on my car's headlight I would only have to connect the solenoid to the lens in order to make it high and low beam lens

[@TraciaKurosawa]

This vid was exactly what I was looking for. Although some things happened so fast I barely knew what you were doing, but still, thanks.

[@TraciaKurosawa]

REally? Didn't know that, I'll check. thanks-

[@sking379]

Thanks Bud!!!

[@newlinkdirect]

Great video, Great job !!

[@jevy0712]

superb... clean installation....

[@stephentoye630]

Hello super job. Do you know if u can do them on an audi b8

[@mihailmariusg]

Great job! You make it look so simple... Can you give an advice how to open Jetta 2012 headlights? As i understand you cannot 'bake' them, as the sealant used from factory is very strong. Some people cut them...but i dont want to use that method. Thanks!

[@sam.raycars]

You made it look so easy 👊💪🤣

[@POISONLIMP]

Awesome mod for a regular headlight, i would like to do it on my 2002 camry le, but i dont know if it is possible...?

[@just206]

Awesome job! My headlight are burnt from the factory fit HIDs on the inside of the lenses, I might join St attempt to try this as new headlights are over £360 + vat each Wah!

[@rensogarcia8159]

Me gusta tu video haces un exelente trabajo bien ilustrado y sin hablar...te felicito Dios te bendiga.

[@Retrofitlab]

¡Muchas gracias!

[@R5GTT]

Brilliant many thanks Sir 😊👍 Was about to purchase a set for my gti but sadly or luckily someone just sold me a pair of bi xenon lights for £100 but thank you all the same for taking the time to reply 😊

[@R5GTT]

+Retrofitlab Thanks again 😊

[@mohamadalamenhijazi4510]

U r doing a great job. It's not easy at all to be done at home.

[@benz_cmon8051]

Do you know how to open the Headlights for a 2012 VW Scirocco? Are they similar to open like the Golf V Headlights?

[@TrutherNews2012]

would this work smoothly on a altima 2010 sedan

[@DeaDPooL-XforceX]

It's like adding Terminator eyes

[@Sulimankhayyat]

it looks awesome

[@hamhamable]

This is the most brilliant heating method I've ever seen! I never had the chance to remove my headlight cover because my microwave oven is too small haha. Btw. can you also use a hair dryer to heat it up? Is it sufficient enough?

[@jaemoonpark4663]

very very good job!!!!

[@joeytheriault3048]

may I ask what that roll of sealer/tape it was u used to seal the lens back on to the housing... this method is very interesting and may have to attempt this

[@sking379]

Hi, I was wondering if I could use the same approach for my 2013 Hyundai Elantra headlights

[@gabrielperdeica6282]

great job. what temperature you're using to ,,BAKE"? Thanks

[@zombie22_]

Anyone else have that problem where you can't seem to get comfortable sitting on the toilet? Nice video btw

[@Retrofitlab]

:D

[@pysk1421]

Amazing! On which temperature is the heat gun set?

[@vipulgoel8482]

Nyc n clean work done !

[@fa2919]

How do you adjust the horizontal alignment of the beam..I've been retrofitting for years but can't find another way than putting the headlight on the car and adjusting against a wall before putting lens back on..any tips?? Thanks

[@valeriopiroddi]

Hello,have a tutorial that explain how we can take the audi a4 ( b8/8k ) led into a Audi A3 headlights?thank you so much

[@alinana1939]

Hello there. Can we turn on the valeo brand headlights by heating this way?

[@lazythatzme]

I want to know do u have to sand down the housing? Is the thread shaft in the back of the projector long enough for both the nut, metal washer and the hid bulb holder? I have a Audi a4 b7 halogen reflector housing

[@andryantobanpol7048]

good video....

[@user-pb7tw9yh4w]

Good!

[@erozik]

Awesome job! Does the heating part for taking off the lens works also on A6 C6 headlight. I have heard that there is some different sealent used and its not going to melt?

[@Moriggia]

Hello, how much temperature you put at the phon? thanks

[@TheMoarly]

Very Cool !!! Hi, which shrouds do you use here? A4 B7 How is the shroud named in your Online-Shop?

[@ivanncee]

With what are you sealing the headlight on the end? Thanks

[@johnnybilly7549]

can you modify the headlight of kia picanto 2016? please! :)

[@jake90770]

HI there guys have you done any Nissan altima 2007-2009 sedan looks like there no much room to fit the shrouds

[@isicks2k128]

hey wts up man u do a great job on this nice vid!!! i want to retrofit my del sol any help?

[@joeskerratt4718]

Hello, This is a good tutorial and I'm grateful but there's something I'm confused about. At the end, you take the connector to the original filament bulb (is that a H7 connector?) and you patch it into the HID's. I assume the point of this is to avoid having numerous wires coming out the back of your headlight. How do you work that out? My headlight is very similar to this (it's a VW) so it would be a massive help if you could explain how you worked this out. Otherwise I have loads of wires coming out the back, the wiring harness going in, plus the bulbs :( If I could avoid having the wiring harness going in so all I have to plug in is the bulbs, that would be amazing. Thanks.

[@ricardoabc3]

4:57 This lamp is what brand? Thank you!

[@dariocaruso792]

hello, thanks for the reply. no, I know ... it's just to see how you disassemble your channel. But I would like to know if you know where they sell them

[@jotsy83]

Hello there. I like your videos. I have an Audi A4 B7 2007 with stock bi Xenon headlights, but my right Hi Beam won't engage. Soon as I turn my HI Beams on right light starts switching between HI and Low beam. Is there any magnetic motor that holds HI beam ON, and is there any way to fix this problem? Thank you!

[@kokotadack]

Is it the same with Golf IV headlights? Is it possible to install the new projectors without cutting or grinding the oem reflectors? Maybe you could post a video on how to work that out on a Golf IV? Thanks!

[@DenioZiamdenioz]

Lekker!

[@shelbythomas5765]

Hi do you have à vidéo with an audi a3 8p (2004-2008) ?

[@h22sparkle]

Retrofitlab I definitely will be using this technique to do my retrofit this way

[@Csabi071]

+Retrofitlab headlight washer not required?

[@UPCarTuto]

Hello, friend! It is normal this projector shake when the vehicle is moving even in places plans?

[@UPCarTuto]

I'm using rubbers and are properly tight, eatou xomeçando to suspect that the vibration comes from the lighthouse baffle, already took a case like this? Type it vibrates a little tried to shoot and the cell captures not.

[@UPCarTuto]

+Retrofitlab Really the problem is the lighthouse, confirmed yesterday. Thanks for attention. People here always ask where the best place to buy projectors always indicate your website.

[@sergiogarza1152]

muy bueno el video

[@neo1gen]

sick

[@skunklusscrew985]

what is the stuff u apply to the projector before put the shrouds on?where can i get it from?

[@YrysSariev]

жду ретрофита от автора на mercedes w211 2003 года галоген ! посмотрим что получится если конечно выйдет ролик

[@franciscowestenhofen7446]

What model of this projector that works in the low beam that seems to be the same as the Tiguan And what is the 2nd wire that connects in parallel with high beam? And also the 2 wire on the projector installed

[@dimitri_mk3]

Very good video!! But what about CanBus? Appears Bulb Error?

[@silviublaj9719]

for bmw f20 can i use this kit also ?? 1 series halogen lamp 2014..it has not so much space inside the headlamp , i would like 2.5" with angel eyes also

[@silviublaj9719]

Can you share a video regarding the F20 , retrofiting , is a popular model in all big citys from europe (i think is the 3 rd in sell numbers for bmw after 3 and 5 series) .And would be the only video on youtube , i didn t found any F20 retrofit also no aftermarket headligst still not available :(. Thanks a lot !!!

[@R5GTT]

Can I ask what the two wires are coming from the lens?. thanks

[@picollokano]

Hi, With the new version, Morimoto Bi-xenon mini H1 6.0, it will be the same ? My car is Audi A4 B7 (8EC) 2007, OEM headlights 8E0 941 003 BK. On Version 6.0 overall size stayed the same, except Width, on 5.0 was 80 mm , on 6.0 is 87 mm, a wider bowl. Will be enough space to insert the projector into headlight ? Thank you !

[@purdu3]

What type of adhesive do we put the lense back on with ?

[@dariocaruso792]

Hi .. your video is very interesting! The method you use to unstick the glass is very ingenious, congratulations! A question I wanted to ask you: where can I find only glass? Thank you, bye.

[@Kthng]

so a normal blow drier will be enough to heat up the lights to break the seal?

[@kalboJeff]

Do you have a video of how you guys made that box where you heat the headlights in? My in laws won't allow me to bake my headlights in their oven.

[@rudeboy1127]

its just a box with a hole big enough to put the heatgun through...

[@keepthinking2666]

will these work for a 2000 audi a6 c5?

[@paasosentomi]

what are those bulbs in the DRL spot? Im thinking to add extra highbeams in that spot aswell. (installed your aharon projectors on my factory afs lights already)

[@Retrofitlab]

Sorry, don't exactly know what you mean, can you tell us the time in the vid you can see it, so we can see what you are referring to? Thanks!

[@aaliux]

What type shrounds do you used on these headlights?

[@feedbrain6257]

this is the best tutorial

[@Retrofitlab]

Thank you! :)

[@xulunj3206]

I'm trying to install an LED strip in my headlights, planning to go for the same approach but using the oven. So, what temperature do I set my oven at? And is it possible that the heat will melt some of the plastic or wires of the LED that I'm going to install..? I'm gonna go check out the specs of my LED strips tho.

[@xulunj3206]

***** Thanks a lot xD I also made sure that the max temperature for my LED strips is 110 degrees Celsius. So 100℃ should work perfectly. xxD

[@dariocaruso792]

another question I wanted to ask you ... what is the name of the adhesive glass rejection rubber? thank you

[@AlienCatcher23]

Do you guys ship to Canada? Also, are these ballasts CANBUS compatible?

[@motochiptuning]

how long and what temperature you hold that box?

[@MinistrantOfSound]

If I want to connect high beams only to the projector solenoid (I don't want to use standard halogen high beam bulb anymore - only bixenon) do I need to use bulb error canceller on "high beam->solenoid" wire? This concerns car with canbus.

[@MinistrantOfSound]

Thank you for answer. I want to save the bixenon look, so no halogen bulb needed for me :) Will do further research on your hid kit offer.

[@osmarq3435]

Does the iris shroud require any trimming to fit into the b7 headlight housing? Is there any modifications required with VAG COM to enable the full functionality or is it ready to go from install only? THANKS !

[@osmarq3435]

great! Thanks for sharing.

[@TheFreakyman81]

hello. i have a Audi A4 B7. Have you a complete Set for this?

[@Pretini4x4Oficial]

Hi, what is the name of the black tape userd to stick the lens back in the lighthouse?

[@iPhrequenC]

what shroud do you chose?

[@mannygsx]

Love your videos and your projects! But can you please point me to where I can replace my OEM headlights from my 06/Audi/s4 without worry about the stupid adaptive light feature? Thank you.

[@mannygsx]

I would like to replace the OEM hid lights with aftermarket hid lights..or just replace the oem ballast with a aftermarket one cause im sick of having to replace a oem ballast every year..

[@kestasburakas376]

good job,i need to now about bulbs,which is the best color temperature 4300k 5000k 6000k.

[@andr3ybmw]

for a6 c5 year 2000, i have headlights whit projectors OEM, and i want to change just projectors, what projectors I need to change only ? 2.5 or 3 inch ?

[@ChrisCas22]

super silent i like it lol

[@Limak2005]

what type of seals used the

[@ClutchMaster14]

I wish you guys could do that to my 07 Ford Focus. But I'm in Florida. :( ....I'd pay you $250 for both projectors install and installing an 8000K HID bulb behind it.

[@NocturneOP55N1]

Using this retrofit how do you regulate the height of the beam if you install this in a halogen headlight?

[@Retrofitlab]

The height can be adjusted via the original adjustment screws on the headlight.

[@NocturneOP55N1]

@@Retrofitlab But not with the one next to the headlight switch, right?

[@Retrofitlab]

@@NocturneOP55N1 Yes the electrical adjuster can still be used! :)

[@user-dq5uf8jf6j]

Автору спасибо! От меня лайк + подписка на канал. Жду обзора на Ford mondeo 3 )))

[@Neco8582]

gute arbeit

[@gil2319]

Really Nice man ,what kind of sealer do you use? Were i can buy it?