RHINO Curves and Surfaces

[@laxmibohora6082]

one of the best tutorials i have watched for Rhino. Thank you very much, John!

[@AxelSolares1983]

Amazing tutorial!!! Very clear and concise. Thank you very much John.

[@Goodnightdemons]

THANK YOU SO MUCH! I had a project I could not figure out planar surfaces until I saw it here! Thank you!

[@MrC3497943]

Excellent tutorial. Thanks for explaining the basics in a swift and easily digestible manner.

[@TheTrippleTKA]

Holy mother load of information!! This video is amazing! A 30 min video makes my head spin. I have ADD and I kept getting distracted. But once I was able to sit through and watch you go over the feature.. phew! learned a lot! Thank you! For creating this!

[@f612CreatorsPodcast]

this tutorial saved my life. Learning rhino has been so annoying coming from mesh modeling thanbk you so much

[@onzkicg]

Amazing, thanks for sharing!

[@gertjohangous9342]

Very informative, well done thanks

[@antonschmid229]

Super Video , helps a ton.. thank you

[@chandreshsharmachans]

This video of yours helped me a lot. Awesome work. And Thank You.

[@cameroncooper8618]

How do you add thickness to a curve polyline? Like how would you extrude that?

[@shynnsup8383]

Great video, you should do more tutorials. you are pretty good at it and at this software!

[@mimibecks7049]

Hi, Thank you for excellent video. I learned a lot about commands and use if shift and Alt keys and others that I did not know they existed. For me and as begiñner, you were going a bit too fast and I had to stop and repeat many times. As suggestion, if you can slow down a bit, that would be great. Otherwise, a great tutorial and I really like Rhino. I have studied AutoCad, inventor, fusion 360, solid works and now trying to shift to Rhino simply because I can buy the software instead going to see subscriptions that can add up quickly. The only thing that I did not like so far is extrude of curve using a curve. I do woodworking and typically I draw my profile perpendicular to rectangle and I extrude my profile around the rectangle and I end up with mitered joint at each corner. That is not the case in Rhino. I had to create a cutting curve and do a lot of trimming to get mitered look at each corner. Thank you Mimi

[@luiseduardomunhoz7886]

I need learne more about control points in sufaces...

[@VickyVyNguyen]

Thank you!! Life saver

[@wenit0]

Amazing video!

[@kurilladesign]

nice. you make any videos with organics - flowers or leaves? animals?

[@soodonim6109]

lifesaver, thank you

[@gbemisolaosinaike7454]

how do you lift a curve off the plane in presective

[@L091231]

appreciate your work. thanks

[@lukeendo1996]

love the tutorial might want to get a mic though

[@sebleton]

this has helped me so much, thankyou

[@evanc3114]

literally what i needed thank you!

[@pavelbartov2222]

When you are in the Perspective view, how you draw the curve verticaly (z axis)?

[@jayati.design]

Just turn on "ortho" mode.

[@GOUTAMKUMAR-vs3op]

my ortho mode is on but the curve is but d curve is in horizontal wht i have 2 do?

[@jayati.design]

why don't you just make the curve in front view? Otherwise in perspective , if you move your cursor upwards, it automatically snaps between horizontal and vertical. Also , keep planar mode on. If you have anything else you want to ask.. just ping me on my channel.

[@dgeorges6970]

If what others suggested doesn't work for you, it could be this: discourse.mcneel.com/t/elevator-mode-on-mac/6262/3 (solved it for me)

[@dutubinger]

... hit the control button ... and KEEP it pressed then draw and see what happens ;-) it took me also a while ... but the line goes into the z direction ...

[@clintford75]

Nice job, very helpful!

[@danafloraladd]

How do I take a plane xy surface and control faces on the z plane with control points?

[@veryetti]

hey, want to say sorry for my english first. u should press ctrl and draw a line, which will be in the same plane until u press lmb, and than u will start to choose height

[@mattiaspettersson6973]

Thank you! Very helpful! :)

[@matthewlo55]

Easyto understand the use of commands.

[@piotrcimachowski5999]

very nice tutorial John, but the same like Jelena I can't find out how to draw a 3D curve in perspective mode. It's makeing me creasy :) HELP and give us the answer. Best regards Piotr

[@veryetti]

hey, want to say sorry for my english first. u should press ctrl and draw a line, which will be in the same plane until u press lmb, and than u will start to choose height

[@odipanda5673]

is it possible to do surface between 2 closed curve ? for example i have a square and a circle and i want to create a surface between them , edge surface doesnt allow me to make this with closed curve , and I can't find the solution :( can some1 help me ?

[@yanshin1804]

Thanks, can rhino convert surface to solid?

[@ameraanjumanjum7972]

How to find surface area?

[@MFfuji29]

Thank u!

[@TheAvidaEuros]

pretty amazing video :)

[@jelenajeftenic524]

Help please! I cant draw curve in more than one planar (in perspective view), do you know why?

[@veryetti]

hey, want to say sorry for my english first. u should press ctrl and draw a line, which will be in the same plane until u press lmb, and than u will start to choose height

[@arkhiv5150]

Thanks! !!

[@nickhoople9248]

hitting control does not lock my xy coordinate so that I can move into the z axis. does anybody know how to fix this????

[@lorenac1234]

did you firgure out how to do it? I am having the same problem.

[@louis189201]

Hold ctrl and click at the position you wish to move in the z axis. This can also be combined with the tab and shift functionality.

[@bigbossbdf5450]

nice

[@kolkataffgod2674]

When i draw all carve in TOP view. I see only one or two carve up and down

[@salehmansour1]

Patch it is. Thanks

[@AnsarAli-lz4ux]

i need total shell plate created expansion video :-)

[@Deemooo]

I believe what you call "interpret" curve is actually interpolation curve

[@TheTrippleTKA]

ok networksrf is a pain in the ass. the mac version is NOTHING like that. you just basically hit networksrt and it did it. mine is not doing anything even though I gave it three different curve! UGH!

[@TheTrippleTKA]

***** Unable to create surface. NetworkSrf requires three or more curves in each direction. so freaking done with Rhino mac. Windows look so much easier to work around

[@jayati.design]

Rhino for windows is definitely more intuitive..though I use both!

[@f612CreatorsPodcast]

wHY ISNT RHINO PAYING YOU FOR THIS TUTORIAL?> SERIOUSLY THANKS

[@troygarcia4973]

invest in a good microphone

[@daurenaidenov1992]

Very boring