Ten speed transmission leaking air from valve on the top and why. Eaton Fuller Fro16210c shift top🥹

[@caleblee4856]

Good luck on your hunt! Love you videos.

[@Lippyandy]

Hiya just watched your video it was fab.we use to have that transmission here in the UK. I believe if memory serves me right it was a12 speed. I remember the key way in the top cover breaking.and also at the rear of the transmission there was a plate with 2 bolts in front of it there was a pin to use to break and turn .driver would call say he stuck in no man land with his gears.would go out undo the 2 bolts remove the cover stick a screwdriver in the shift it hadT stamped in it turn it to the top fit a new cover plate on his way he would go.

[@etrtruckcenterenginedrivet8918]

Glad you enjoyed the video . Would definitely like to see what you guys are running as far as manual transmissions there in the UK. This is a 10 speed Eaton Fuller top plate by the way but yes there are two different styles of this top. There is a key top and a lug style top and yes the key style top is known for breaking and leaving you stranded.

[@Lippyandy]

Hiya thanks for replying back. Well over here we're using these automatic transmissions I've not had anything to do with them really .There in Daf trucks volvo and scanias .There good when there going right but I no owner operator's that run them. Very very expensive to repair .ie if the computer on top of the gearbox goes thatcan cost up to £3000 pound. Lol I'm 57 old school I like the Eatons back in the day we had 9 and 13 speeds . Then Eaton brought out a gearbox called the Twinsplitter that was a fabulous box

[@b.k.sautomarinedieselrepai5143]

Have you made the video how to test the top plate?

[@andresr7341]

Whats an estimate cost of replacement on that job and down time ?, i noticed i have the same issue. Thx i have a 10spd eaton fuller its on a 2013 587peterbilt

[@GJ20028]

good content.....but I want to know what is the part number of the plate with the components...thanks

[@naturalandsimplelife2131]

Dont understand. How plate is bad? U can clean surface and put back modoler with sealant gasket? Sorry if I m asking stupid question

[@apacheindian5267]

Can that leaking top plate cause air pressure in the secondary tank not to build properly?

[@CashNYC]

Drain your air tanks every morning this happened to me

[@shawnrice7179]

should we be putting wd 40 penetrateing oil in our air tanks?

[@harley13purenrg]

I have a 13 speed. My truck is leaking air at the red splitter button, but only in high gear. I drain my tanks regularly. And have rarely encountered water draining from the tanks. It is an eaton fuller trans, not sure of model. But it is in a 22 lonestar, wiki 320k miles. It just started yesterday, and the leak is faint. But aside from it being annoying, I'm worried it's going to lead to further problems down the line.

[@etrtruckcenterenginedrivet8918]

It could be an issue with the splitter cylinder possibly rust on the inside causing air to bypass around the oring in the piston/cylinder wall.

[@mariothanasi2017]

Hi guys. I had a leak on top of the air module valve( valve itself was cracked and been leaking). With the old valve i had no leaks underneath the valve. I changed with the new one. In the morning when i move the splitter to higher gear i hear air noise not the click, but still changes the gears without problem. After 10 minutes works good, no air leaks sound and does the click up and down normally. What can cause this. Maming me crazy. I opened 3 times the valve..

[@williamsimmons867]

How about a 15 speed bypassing air .want go high to low

[@DannySoto-q3j]

How do u install that top plate back on the transmission?

[@etrtruckcenterenginedrivet8918]

Sub to the channel we have a full length rebuild video of that transmission it’s a step by step tutorial

[@luisxalteno5860]

Hey bud I have a Eaton super 10 that got stuck in gear and I’m trying to get it back to neutral. I took of the tower and I’m playing with the bars. What do you think cause it to get stuck in gear? Should I be worry or could it be a simple fix

[@etrtruckcenterenginedrivet8918]

You may have a broken reverse gear snapring. It needs to come out to be repaired. It’s easy to break a mainshaft when this issue happens.

[@gifinoc3356]

How much does it cost to fix that? Thanks

[@marcelinojuarez5604]

Modulator=600 Top plate= 2800 Labor=1200 Plus miscellaneous, tax and tip 😊

[@etrtruckcenterenginedrivet8918]

😳

[@madrid27100]

Damn , mine can continue leaking air I guess 😂, the top plate cost more than the whole rebuild transmission

[@michaelhatcher873]

​@@madrid27100 right